espat: add Debug field to driver, and the associated behavior you would expect

Signed-off-by: deadprogram <ron@hybridgroup.com>

CHANGELOG.md

@@ -1,3 +1,86 @@
+0.19.0
+---
+- **new devices**
+    - ft6336: add support for ft6336
+    - pca9685: PCA9685 driver
+    - shtc3: Sensirion SHTC3 Relative Humidity / Temperature i2c sensor
+    - sx126x: Driver for Semtech sx126x radio modules
+    - xpt2046: XPT2046 Touch driver (#350)
+- **enhancements**
+    - **hd44780i2c** 
+        - clean up for go fmt
+        - Needed fixes and update hd44780i2c.go
+    - **ili9341, ili9342**
+        - add support for m5stack
+        - add support for m5stack-core2
+    - **wifi**
+        - modify to use shared net.Adapter interface for all supported wifi devices
+    - wifinina: remove busy wait
+- **bugfixes**
+    - **hd44780** 
+        - fix 4-bit data length flag
+        - Reset data pins to output mode after reading
+    - Nano 33 BLE drivers (#351)
+- **docs**
+    - examples/wifi: add unified example for tcpclient that compiles for all supported wifi adaptors
+
+0.18.0
+---
+- **new devices**
+    - apds9960: add support for APDS-9960 Digital Proximity sensor
+    - axp192: add support for AXP192 single Cell Li-Battery and power system management IC
+    - hts221: add support for HTS221 capacitive digital sensor for relative humidity and temperature
+    - i2csoft: add support for software I2C
+    - image: add support for image/jpeg and image/png
+    - lps22hb: add support for LPS22HB MEMS nano pressure sensor
+    - lsm6dox: add support for lsm6dox accelerometer
+    - lsm9ds1: add support for lsm9ds1 accelerometer
+- **enhancements**
+    - ili9341: change to use drivers.SPI interface
+    - **ws2812**
+        - generate assembly instead of handwriting it
+        - improve timings to be compatible with the WS2811
+        - add support for 168MHz (e.g. Adafruit Feather STM32F405)
+        - add support for RISC-V
+    - wifinina: control nina pins, for example leds
+- **docs**
+    - rtl8720dn: examples for tcpclient, udpstation, mqtt, and webserver
+    - **wifinina** 
+        - nina-fw update docs
+        - examples/wifinina/http-get
+    - ili9341: refactor examples
+    - Fix broken link for SHT3x datasheet
+- **core**
+    - all: use build directives for both Go1.17 and earlier versions
+- **bugfixes**
+    - net: fix raddr of tcp conn
+    - mcp3008: fix bitshift bug
+
+0.17.1
+---
+- To correct an error in the release process. Same as 0.17.0.
+
+0.17.0
+---
+- **new devices**
+    - rtl8720dn: add support for rtl8720dn
+    - sdcard: add support for spi sdcard driver, along with fatfs
+- **enhancements**
+    - apa102: use 4-byte buffer to improve speed
+    - bmi160: avoid heap allocations
+    - ili9341: add standard SPI driver
+    - wifinina
+        - avoid fmt package
+        - Fix RSSI command for WiFiNINA + Print current SSID + Wait for correct time before printing it out + Cleanup
+    - ws2812
+        - rename the pin to ws2812
+        - add tag for nrf52833
+        - Disable interrupts before sending ws2812 data
+        - add support for qtpy and atsame5x
+- **core**
+    - modules: switch to use tinygo-org version of tinyfs package
+    - all: use machine.Serial as the default output
+
 0.16.0
 ---
 - **new devices**

LICENSE

@@ -1,4 +1,4 @@
-Copyright (c) 2018-2021 The TinyGo Authors. All rights reserved.
+Copyright (c) 2018-2022 The TinyGo Authors. All rights reserved.
 
 Redistribution and use in source and binary forms, with or without
 modification, are permitted provided that the following conditions are

Makefile

@@ -2,7 +2,7 @@
 clean:
 	@rm -rf build
 
-FMT_PATHS = ./*.go ./examples/**/*.go
+FMT_PATHS = ./
 
 fmt-check:
 	@unformatted=$$(gofmt -l $(FMT_PATHS)); [ -z "$$unformatted" ] && exit 0; echo "Unformatted:"; for fn in $$unformatted; do echo "  $$fn"; done; exit 1
@@ -17,6 +17,8 @@ smoke-test:
 	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=itsybitsy-m0 ./examples/apa102/main.go
 	@md5sum ./build/test.hex
+	tinygo build -size short -o ./build/test.hex -target=nano-33-ble ./examples/apds9960/proximity/main.go
+	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=itsybitsy-m0 ./examples/apa102/itsybitsy-m0/main.go
 	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=microbit ./examples/at24cx/main.go
@@ -63,6 +65,8 @@ smoke-test:
 	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=arduino-nano33 ./examples/hd44780i2c/main.go
 	@md5sum ./build/test.hex
+	tinygo build -size short -o ./build/test.hex -target=nano-33-ble ./examples/hts221/main.go
+	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=microbit ./examples/hub75/main.go
 	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=pyportal ./examples/ili9341/basic
@@ -75,8 +79,12 @@ smoke-test:
 	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=xiao ./examples/ili9341/scroll
 	@md5sum ./build/test.hex
+	tinygo build -size short -o ./build/test.hex -target=pyportal ./examples/ili9341/slideshow
+	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=circuitplay-express ./examples/lis3dh/main.go
 	@md5sum ./build/test.hex
+	tinygo build -size short -o ./build/test.hex -target=nano-33-ble ./examples/lps22hb/main.go
+	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=microbit ./examples/lsm303agr/main.go
 	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=arduino-nano33 ./examples/lsm6ds3/main.go
@@ -109,6 +117,8 @@ smoke-test:
 	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=microbit ./examples/sht3x/main.go
 	@md5sum ./build/test.hex
+	tinygo build -size short -o ./build/test.hex -target=microbit ./examples/shtc3/main.go
+	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=microbit ./examples/ssd1306/i2c_128x32/main.go
 	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=microbit ./examples/ssd1306/spi_128x64/main.go
@@ -179,8 +189,8 @@ endif
 	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=feather-m0 ./examples/dht/main.go
 	@md5sum ./build/test.hex
-	tinygo build -size short -o ./build/test.hex -target=arduino ./examples/keypad4x4/main.go
-	@md5sum ./build/test.hex
+	# tinygo build -size short -o ./build/test.hex -target=arduino ./examples/keypad4x4/main.go
+	# @md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=xiao ./examples/pcf8563/alarm/
 	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=xiao ./examples/pcf8563/clkout/
@@ -197,12 +207,31 @@ endif
 	@md5sum ./build/test.hex
 	tinygo build -size short -o ./build/test.hex -target=feather-m4 ./examples/sdcard/tinyfs/
 	@md5sum ./build/test.hex
+	tinygo build -size short -o ./build/test.hex -target=wioterminal ./examples/rtl8720dn/webclient/
+	@md5sum ./build/test.hex
+	tinygo build -size short -o ./build/test.hex -target=wioterminal ./examples/rtl8720dn/webserver/
+	@md5sum ./build/test.hex
+	tinygo build -size short -o ./build/test.hex -target=wioterminal ./examples/rtl8720dn/mqttsub/
+	@md5sum ./build/test.hex
+	tinygo build -size short -o ./build/test.hex -target=feather-m4 ./examples/i2csoft/adt7410/
+	@md5sum ./build/test.hex
+	tinygo build -size short -o ./build/test.elf -target=wioterminal ./examples/axp192/m5stack-core2-blinky/
+	@md5sum ./build/test.hex
+	tinygo build -size short -o ./build/test.uf2 -target=pico ./examples/xpt2046/main.go
+	@md5sum ./build/test.uf2
+	tinygo build -size short -o ./build/test.elf -target=m5stack-core2 ./examples/ft6336/basic/
+	@md5sum ./build/test.elf
+	tinygo build -size short -o ./build/test.elf -target=m5stack-core2 ./examples/ft6336/touchpaint/
+	@md5sum ./build/test.elf
+	tinygo build -size short -o ./build/test.hex -target=nucleo-wl55jc ./examples/sx126x/lora_rxtx/
+	@md5sum ./build/test.hex
 
 DRIVERS = $(wildcard */)
 NOTESTS = build examples flash semihosting pcd8544 shiftregister st7789 microphone mcp3008 gps microbitmatrix \
 		hcsr04 ssd1331 ws2812 thermistor apa102 easystepper ssd1351 ili9341 wifinina shifter hub75 \
 		hd44780 buzzer ssd1306 espat l9110x st7735 bmi160 l293x dht keypad4x4 max72xx p1am tone tm1637 \
-		pcf8563 mcp2515 servo sdcard
+		pcf8563 mcp2515 servo sdcard rtl8720dn image cmd i2csoft hts221 lps22hb apds9960 axp192 xpt2046 \
+		ft6336 sx126x
 TESTS = $(filter-out $(addsuffix /%,$(NOTESTS)),$(DRIVERS))
 
 unit-test:

README.md

@@ -52,7 +52,7 @@ func main() {
 
 ## Currently supported devices
 
-The following 66 devices are supported.
+The following 78 devices are supported.
 
 | Device Name | Interface Type |
 |----------|-------------|
@@ -61,7 +61,9 @@ The following 66 devices are supported.
 | [AHT20 I2C Temperature and Humidity Sensor](http://www.aosong.com/userfiles/files/media/AHT20%20%E8%8B%B1%E6%96%87%E7%89%88%E8%AF%B4%E6%98%8E%E4%B9%A6%20A0%2020201222.pdf) | I2C |
 | [AMG88xx 8x8 Thermal camera sensor](https://cdn-learn.adafruit.com/assets/assets/000/043/261/original/Grid-EYE_SPECIFICATIONS%28Reference%29.pdf) | I2C |
 | [APA102 RGB LED](https://cdn-shop.adafruit.com/product-files/2343/APA102C.pdf) | SPI |
+| [APDS9960 Digital proximity, ambient light, RGB and gesture sensor](https://cdn.sparkfun.com/assets/learn_tutorials/3/2/1/Avago-APDS-9960-datasheet.pdf) | I2C |
 | [AT24CX 2-wire serial EEPROM](https://www.openimpulse.com/blog/wp-content/uploads/wpsc/downloadables/24C32-Datasheet.pdf) | I2C |
+| [AXP192 single Cell Li-Battery and Power System Management](https://github.com/m5stack/M5-Schematic/blob/master/Core/AXP192%20Datasheet_v1.1_en_draft_2211.pdf) | I2C |
 | [BBC micro:bit LED matrix](https://github.com/bbcmicrobit/hardware/blob/master/SCH_BBC-Microbit_V1.3B.pdf) | GPIO |
 | [BH1750 ambient light sensor](https://www.mouser.com/ds/2/348/bh1750fvi-e-186247.pdf) | I2C |
 | [BlinkM RGB LED](http://thingm.com/fileadmin/thingm/downloads/BlinkM_datasheet.pdf) | I2C |
@@ -76,10 +78,13 @@ The following 66 devices are supported.
 | [DS3231 real time clock](https://datasheets.maximintegrated.com/en/ds/DS3231.pdf) | I2C |
 | [ESP32 as WiFi Coprocessor with Arduino nina-fw](https://github.com/arduino/nina-fw) | SPI |
 | [ESP8266/ESP32 AT Command set for WiFi/TCP/UDP](https://github.com/espressif/esp32-at) | UART |
+| [FT6336 touch controller](https://focuslcds.com/content/FT6236.pdf) | I2C |
 | [GPS module](https://www.u-blox.com/en/product/neo-6-series) | I2C/UART |
 | [HC-SR04 Ultrasonic distance sensor](https://cdn.sparkfun.com/datasheets/Sensors/Proximity/HCSR04.pdf) | GPIO |
 | [HD44780 LCD controller](https://www.sparkfun.com/datasheets/LCD/HD44780.pdf) | GPIO/I2C |
+| [HTS221 digital humidity and temperature sensor](https://www.st.com/resource/en/datasheet/hts221.pdf) | I2C |
 | [HUB75 RGB led matrix](https://cdn-learn.adafruit.com/downloads/pdf/32x16-32x32-rgb-led-matrix.pdf) | SPI |
+| [software I2C driver](https://www.ti.com/lit/an/slva704/slva704.pdf) | GPIO |
 | [ILI9341 TFT color display](https://cdn-shop.adafruit.com/datasheets/ILI9341.pdf) | SPI |
 | [INA260 Volt/Amp/Power meter](https://www.ti.com/lit/ds/symlink/ina260.pdf) | I2C |
 | [4x4 Membrane Keypad](https://cdn.sparkfun.com/assets/f/f/a/5/0/DS-16038.pdf) | GPIO |
@@ -87,12 +92,16 @@ The following 66 devices are supported.
 | [L9110x motor driver](https://www.elecrow.com/download/datasheet-l9110.pdf) | GPIO/PWM |
 | [LIS2MDL magnetometer](https://www.st.com/resource/en/datasheet/lis2mdl.pdf) | I2C |
 | [LIS3DH accelerometer](https://www.st.com/resource/en/datasheet/lis3dh.pdf) | I2C |
+| [LPS22HB MEMS nano pressure sensor](https://www.st.com/resource/en/datasheet/dm00140895.pdf) | I2C |
 | [LSM6DS3 accelerometer](https://www.st.com/resource/en/datasheet/lsm6ds3.pdf) | I2C |
+| [LSM6DSOX accelerometer](https://www.st.com/resource/en/datasheet/lsm6dsox.pdf) | I2C |
+| [LSM303AGR accelerometer](https://www.st.com/resource/en/datasheet/lsm303agr.pdf) | I2C |
+| [LSM9DS1 accelerometer](https://www.st.com/resource/en/datasheet/lsm9ds1.pdf) | I2C |
 | [MAG3110 magnetometer](https://www.nxp.com/docs/en/data-sheet/MAG3110.pdf) | I2C |
 | [MAX7219 & MAX7221 display driver](https://datasheets.maximintegrated.com/en/ds/MAX7219-MAX7221.pdf) | SPI |
-| [MCP23017 port expander](https://ww1.microchip.com/downloads/en/DeviceDoc/20001952C.pdf) | I2C |
-| [MCP3008 analog to digital converter (ADC)](http://ww1.microchip.com/downloads/en/DeviceDoc/21295d.pdf) | SPI |
 | [MCP2515 Stand-Alone CAN Controller with SPI Interface](https://ww1.microchip.com/downloads/en/DeviceDoc/MCP2515-Family-Data-Sheet-DS20001801K.pdf) | SPI |
+| [MCP3008 analog to digital converter (ADC)](http://ww1.microchip.com/downloads/en/DeviceDoc/21295d.pdf) | SPI |
+| [MCP23017 port expander](https://ww1.microchip.com/downloads/en/DeviceDoc/20001952C.pdf) | I2C |
 | [Microphone - PDM](https://cdn-learn.adafruit.com/assets/assets/000/049/977/original/MP34DT01-M.pdf) | I2S/PDM |
 | [MMA8653 accelerometer](https://www.nxp.com/docs/en/data-sheet/MMA8653FC.pdf) | I2C |
 | [MPU6050 accelerometer/gyroscope](https://store.invensense.com/datasheets/invensense/MPU-6050_DataSheet_V3%204.pdf) | I2C |
@@ -100,11 +109,13 @@ The following 66 devices are supported.
 | [PCD8544 display](http://eia.udg.edu/~forest/PCD8544_1.pdf) | SPI |
 | [PCF8563 real time clock](https://www.nxp.com/docs/en/data-sheet/PCF8563.pdf) | I2C |
 | [Resistive Touchscreen (4-wire)](http://ww1.microchip.com/downloads/en/Appnotes/doc8091.pdf) | GPIO |
+| [RTL8720DN 2.4G/5G Dual Bands Wireless and BLE5.0](https://www.seeedstudio.com/Realtek8720DN-2-4G-5G-Dual-Bands-Wireless-and-BLE5-0-Combo-Module-p-4442.html) | UART |
 | [Semihosting](https://wiki.segger.com/Semihosting) | Debug |
 | [Servo](https://learn.sparkfun.com/tutorials/hobby-servo-tutorial/all) | PWM |
 | [Shift register (PISO)](https://en.wikipedia.org/wiki/Shift_register#Parallel-in_serial-out_\(PISO\)) | GPIO |
 | [Shift registers (SIPO)](https://en.wikipedia.org/wiki/Shift_register#Serial-in_parallel-out_(SIPO)) | GPIO |
-| [SHT3x Digital Humidity Sensor](https://www.sensirion.com/fileadmin/user_upload/customers/sensirion/Dokumente/0_Datasheets/Humidity/Sensirion_Humidity_Sensors_SHT3x_Datasheet_digital.pdf) | I2C |
+| [SHT3x Digital Humidity Sensor](https://www.sensirion.com/fileadmin/user_upload/customers/sensirion/Dokumente/2_Humidity_Sensors/Datasheets/Sensirion_Humidity_Sensors_SHT3x_Datasheet_digital.pdf) | I2C |
+| [SHTC3 Digital Humidity Sensor (RH/T)](https://www.sensirion.com/fileadmin/user_upload/customers/sensirion/Dokumente/2_Humidity_Sensors/Datasheets/Sensirion_Humidity_Sensors_SHTC3_Datasheet.pdf) | I2C |
 | [SPI NOR Flash Memory](https://en.wikipedia.org/wiki/Flash_memory#NOR_flash) | SPI/QSPI |
 | [SPI SDCARD/MMC](https://en.wikipedia.org/wiki/SD_card) | SPI |
 | [SSD1306 OLED display](https://cdn-shop.adafruit.com/datasheets/SSD1306.pdf) | I2C / SPI |
@@ -122,6 +133,8 @@ The following 66 devices are supported.
 | [Waveshare 2.13" e-paper display](https://www.waveshare.com/w/upload/e/e6/2.13inch_e-Paper_Datasheet.pdf) | SPI |
 | [Waveshare 4.2" e-paper B/W display](https://www.waveshare.com/w/upload/6/6a/4.2inch-e-paper-specification.pdf) | SPI |
 | [WS2812 RGB LED](https://cdn-shop.adafruit.com/datasheets/WS2812.pdf) | GPIO |
+| [XPT2046 touch controller](http://grobotronics.com/images/datasheets/xpt2046-datasheet.pdf) | GPIO |
+| [Semtech SX126x Lora](https://www.semtech.com/products/wireless-rf/lora-transceiv-ers/sx1261) | SPI |
 
 ## Contributing
 

apds9960/apds9960.go

@@ -0,0 +1,468 @@
+// Package apds9960 implements a driver for APDS-9960,
+// a digital proximity, ambient light, RGB and gesture sensor.
+//
+// Datasheet: https://cdn.sparkfun.com/assets/learn_tutorials/3/2/1/Avago-APDS-9960-datasheet.pdf
+//
+package apds9960
+
+import (
+	"time"
+
+	"tinygo.org/x/drivers"
+)
+
+// Device wraps an I2C connection to a APDS-9960 device.
+type Device struct {
+	bus     drivers.I2C
+	Address uint8
+	mode    uint8
+	gesture gestureData
+}
+
+// Configuration for APDS-9960 device.
+type Configuration struct {
+	ProximityPulseLength uint8
+	ProximityPulseCount  uint8
+	GesturePulseLength   uint8
+	GesturePulseCount    uint8
+	ProximityGain        uint8
+	GestureGain          uint8
+	ColorGain            uint8
+	ADCIntegrationCycles uint16
+	LEDBoost             uint16
+	threshold            uint8
+	sensitivity          uint8
+}
+
+// for gesture-related data
+type gestureData struct {
+	detected    uint8
+	threshold   uint8
+	sensitivity uint8
+	gXDelta     int16
+	gYDelta     int16
+	gXPrevDelta int16
+	gYPrevDelta int16
+	received    bool
+}
+
+// for enabling various device function
+type enableConfig struct {
+	GEN  bool
+	PIEN bool
+	AIEN bool
+	WEN  bool
+	PEN  bool
+	AEN  bool
+	PON  bool
+}
+
+// New creates a new APDS-9960 connection. The I2C bus must already be
+// configured.
+//
+// This function only creates the Device object, it does not touch the device.
+func New(bus drivers.I2C) Device {
+	return Device{bus: bus, Address: ADPS9960_ADDRESS, mode: MODE_NONE}
+}
+
+// Connected returns whether APDS-9960 has been found.
+// It does a "who am I" request and checks the response.
+func (d *Device) Connected() bool {
+	data := []byte{0}
+	d.bus.ReadRegister(d.Address, APDS9960_ID_REG, data)
+	return data[0] == 0xAB
+}
+
+// GetMode returns current engine mode
+func (d *Device) GetMode() uint8 {
+	return d.mode
+}
+
+// DisableAll turns off the device and all functions
+func (d *Device) DisableAll() {
+	d.enable(enableConfig{})
+	d.bus.WriteRegister(d.Address, APDS9960_GCONF4_REG, []byte{0x00})
+	d.mode = MODE_NONE
+	d.gesture.detected = GESTURE_NONE
+}
+
+// SetProximityPulse sets proximity pulse length (4, 8, 16, 32) and count (1~64)
+// default: 16, 64
+func (d *Device) SetProximityPulse(length, count uint8) {
+	d.bus.WriteRegister(d.Address, APDS9960_PPULSE_REG, []byte{getPulseLength(length)<<6 | getPulseCount(count)})
+}
+
+// SetGesturePulse sets gesture pulse length (4, 8, 16, 32) and count (1~64)
+// default: 16, 64
+func (d *Device) SetGesturePulse(length, count uint8) {
+	d.bus.WriteRegister(d.Address, APDS9960_GPULSE_REG, []byte{getPulseLength(length)<<6 | getPulseCount(count)})
+}
+
+// SetADCIntegrationCycles sets ALS/color ADC internal integration cycles (1~256, 1 cycle = 2.78 ms)
+// default: 4 (~10 ms)
+func (d *Device) SetADCIntegrationCycles(cycles uint16) {
+	if cycles > 256 {
+		cycles = 256
+	}
+	d.bus.WriteRegister(d.Address, APDS9960_ATIME_REG, []byte{uint8(256 - cycles)})
+}
+
+// SetGains sets proximity/gesture gain (1, 2, 4, 8x) and ALS/color gain (1, 4, 16, 64x)
+// default: 1, 1, 4
+func (d *Device) SetGains(proximityGain, gestureGain, colorGain uint8) {
+	d.bus.WriteRegister(d.Address, APDS9960_CONTROL_REG, []byte{getProximityGain(proximityGain)<<2 | getALSGain(colorGain)})
+	d.bus.WriteRegister(d.Address, APDS9960_GCONF2_REG, []byte{getProximityGain(gestureGain) << 5})
+}
+
+// LEDBoost sets proximity and gesture LED current level (100, 150, 200, 300 (%))
+// default: 100
+func (d *Device) LEDBoost(percent uint16) {
+	var v uint8
+	switch percent {
+	case 100:
+		v = 0
+	case 150:
+		v = 1
+	case 200:
+		v = 2
+	case 300:
+		v = 3
+	}
+	d.bus.WriteRegister(d.Address, APDS9960_CONFIG2_REG, []byte{0x01 | v<<4})
+}
+
+// Setthreshold sets threshold (0~255) for detecting gestures
+// default: 30
+func (d *Device) Setthreshold(t uint8) {
+	d.gesture.threshold = t
+}
+
+// Setsensitivity sets sensivity (0~100) for detecting gestures
+// default: 20
+func (d *Device) Setsensitivity(s uint8) {
+	if s > 100 {
+		s = 100
+	}
+	d.gesture.sensitivity = 100 - s
+}
+
+// EnableProximity starts the proximity engine
+func (d *Device) EnableProximity() {
+	if d.mode != MODE_NONE {
+		d.DisableAll()
+	}
+	d.enable(enableConfig{PON: true, PEN: true, WEN: true})
+	d.mode = MODE_PROXIMITY
+}
+
+// ProximityAvailable reports if proximity data is available
+func (d *Device) ProximityAvailable() bool {
+	if d.mode == MODE_PROXIMITY && d.readStatus("PVALID") {
+		return true
+	}
+	return false
+}
+
+// ReadProximity reads proximity data (0~255)
+func (d *Device) ReadProximity() (proximity int32) {
+	if d.mode != MODE_PROXIMITY {
+		return 0
+	}
+	data := []byte{0}
+	d.bus.ReadRegister(d.Address, APDS9960_PDATA_REG, data)
+	return 255 - int32(data[0])
+}
+
+// EnableColor starts the color engine
+func (d *Device) EnableColor() {
+	if d.mode != MODE_NONE {
+		d.DisableAll()
+	}
+	d.enable(enableConfig{PON: true, AEN: true, WEN: true})
+	d.mode = MODE_COLOR
+}
+
+// ColorAvailable reports if color data is available
+func (d *Device) ColorAvailable() bool {
+	if d.mode == MODE_COLOR && d.readStatus("AVALID") {
+		return true
+	}
+	return false
+}
+
+// ReadColor reads color data (red, green, blue, clear color/brightness)
+func (d *Device) ReadColor() (r int32, g int32, b int32, clear int32) {
+	if d.mode != MODE_COLOR {
+		return
+	}
+	data := []byte{0, 0, 0, 0, 0, 0, 0, 0}
+	d.bus.ReadRegister(d.Address, APDS9960_CDATAL_REG, data[:1])
+	d.bus.ReadRegister(d.Address, APDS9960_CDATAH_REG, data[1:2])
+	d.bus.ReadRegister(d.Address, APDS9960_RDATAL_REG, data[2:3])
+	d.bus.ReadRegister(d.Address, APDS9960_RDATAH_REG, data[3:4])
+	d.bus.ReadRegister(d.Address, APDS9960_GDATAL_REG, data[4:5])
+	d.bus.ReadRegister(d.Address, APDS9960_GDATAH_REG, data[5:6])
+	d.bus.ReadRegister(d.Address, APDS9960_BDATAL_REG, data[6:7])
+	d.bus.ReadRegister(d.Address, APDS9960_BDATAH_REG, data[7:])
+	clear = int32(uint16(data[1])<<8 | uint16(data[0]))
+	r = int32(uint16(data[3])<<8 | uint16(data[2]))
+	g = int32(uint16(data[5])<<8 | uint16(data[4]))
+	b = int32(uint16(data[7])<<8 | uint16(data[6]))
+	return
+}
+
+// EnableGesture starts the gesture engine
+func (d *Device) EnableGesture() {
+	if d.mode != MODE_NONE {
+		d.DisableAll()
+	}
+	d.enable(enableConfig{PON: true, PEN: true, GEN: true, WEN: true})
+	d.mode = MODE_GESTURE
+	d.gesture.detected = GESTURE_NONE
+	d.gesture.gXDelta = 0
+	d.gesture.gYDelta = 0
+	d.gesture.gXPrevDelta = 0
+	d.gesture.gYPrevDelta = 0
+	d.gesture.received = false
+}
+
+// GestureAvailable reports if gesture data is available
+func (d *Device) GestureAvailable() bool {
+	if d.mode != MODE_GESTURE {
+		return false
+	}
+
+	data := []byte{0, 0, 0, 0}
+
+	// check GVALID
+	d.bus.ReadRegister(d.Address, APDS9960_GSTATUS_REG, data[:1])
+	if data[0]&0x01 == 0 {
+		return false
+	}
+
+	// get number of data sets available in FIFO
+	d.bus.ReadRegister(d.Address, APDS9960_GFLVL_REG, data[:1])
+	availableDataSets := data[0]
+	if availableDataSets == 0 {
+		return false
+	}
+
+	// read up, down, left and right proximity data from FIFO
+	var dataSets [32][4]uint8
+	for i := uint8(0); i < availableDataSets; i++ {
+		d.bus.ReadRegister(d.Address, APDS9960_GFIFO_U_REG, data[:1])
+		d.bus.ReadRegister(d.Address, APDS9960_GFIFO_D_REG, data[1:2])
+		d.bus.ReadRegister(d.Address, APDS9960_GFIFO_L_REG, data[2:3])
+		d.bus.ReadRegister(d.Address, APDS9960_GFIFO_R_REG, data[3:4])
+		for j := uint8(0); j < 4; j++ {
+			dataSets[i][j] = data[j]
+		}
+	}
+
+	// gesture detection process
+	d.gesture.detected = GESTURE_NONE
+	for i := uint8(0); i < availableDataSets; i++ {
+		U := dataSets[i][0]
+		D := dataSets[i][1]
+		L := dataSets[i][2]
+		R := dataSets[i][3]
+
+		// if all readings fall below threshold, it's possible that
+		// a movement's just been made
+		if U < d.gesture.threshold && D < d.gesture.threshold && L < d.gesture.threshold && R < d.gesture.threshold {
+			d.gesture.received = true
+			// if there were movement in the previous step (including the last data sets)
+			if d.gesture.gXPrevDelta != 0 && d.gesture.gYPrevDelta != 0 {
+				totalX := d.gesture.gXPrevDelta - d.gesture.gXDelta
+				totalY := d.gesture.gYPrevDelta - d.gesture.gYDelta
+				// if previous and current movement are in opposite directions (pass through one led then next)
+				// and the difference is big enough, the gesture is recorded
+				switch {
+				case totalX < -int16(d.gesture.sensitivity):
+					d.gesture.detected = GESTURE_LEFT
+				case totalX > int16(d.gesture.sensitivity):
+					d.gesture.detected = GESTURE_RIGHT
+				case totalY > int16(d.gesture.sensitivity):
+					d.gesture.detected = GESTURE_DOWN
+				case totalY < -int16(d.gesture.sensitivity):
+					d.gesture.detected = GESTURE_UP
+				}
+				d.gesture.gXDelta = 0
+				d.gesture.gYDelta = 0
+				d.gesture.gXPrevDelta = 0
+				d.gesture.gYPrevDelta = 0
+			}
+			continue
+		}
+
+		// recording current movement
+		d.gesture.gXDelta = int16(R) - int16(L)
+		d.gesture.gYDelta = int16(D) - int16(U)
+		if d.gesture.received {
+			d.gesture.received = false
+			d.gesture.gXPrevDelta = d.gesture.gXDelta
+			d.gesture.gYPrevDelta = d.gesture.gYDelta
+		}
+	}
+
+	return d.gesture.detected != GESTURE_NONE
+}
+
+// ReadGesture reads last gesture data
+func (d *Device) ReadGesture() (gesture int32) {
+	return int32(d.gesture.detected)
+}
+
+// private functions
+
+func (d *Device) configureDevice(cfg Configuration) {
+	d.DisableAll() // turn off everything
+
+	// "default" settings
+	if cfg.ProximityPulseLength == 0 {
+		cfg.ProximityPulseLength = 16
+	}
+	if cfg.ProximityPulseCount == 0 {
+		cfg.ProximityPulseCount = 64
+	}
+	if cfg.GesturePulseLength == 0 {
+		cfg.GesturePulseLength = 16
+	}
+	if cfg.GesturePulseCount == 0 {
+		cfg.GesturePulseCount = 64
+	}
+	if cfg.ProximityGain == 0 {
+		cfg.ProximityGain = 1
+	}
+	if cfg.GestureGain == 0 {
+		cfg.GestureGain = 1
+	}
+	if cfg.ColorGain == 0 {
+		cfg.ColorGain = 4
+	}
+	if cfg.ADCIntegrationCycles == 0 {
+		cfg.ADCIntegrationCycles = 4
+	}
+	if cfg.threshold == 0 {
+		d.gesture.threshold = 30
+	}
+	if cfg.sensitivity == 0 {
+		d.gesture.sensitivity = 20
+	}
+
+	d.SetProximityPulse(cfg.ProximityPulseLength, cfg.ProximityPulseCount)
+	d.SetGesturePulse(cfg.GesturePulseLength, cfg.GesturePulseCount)
+	d.SetGains(cfg.ProximityGain, cfg.GestureGain, cfg.ColorGain)
+	d.SetADCIntegrationCycles(cfg.ADCIntegrationCycles)
+
+	if cfg.LEDBoost > 0 {
+		d.LEDBoost(cfg.LEDBoost)
+	}
+}
+
+func (d *Device) enable(cfg enableConfig) {
+	var gen, pien, aien, wen, pen, aen, pon uint8
+
+	if cfg.GEN {
+		gen = 1
+	}
+	if cfg.PIEN {
+		pien = 1
+	}
+	if cfg.AIEN {
+		aien = 1
+	}
+	if cfg.WEN {
+		wen = 1
+	}
+	if cfg.PEN {
+		pen = 1
+	}
+	if cfg.AEN {
+		aen = 1
+	}
+	if cfg.PON {
+		pon = 1
+	}
+
+	data := []byte{gen<<6 | pien<<5 | aien<<4 | wen<<3 | pen<<2 | aen<<1 | pon}
+	d.bus.WriteRegister(d.Address, APDS9960_ENABLE_REG, data)
+
+	if cfg.PON {
+		time.Sleep(time.Millisecond * 10)
+	}
+}
+
+func (d *Device) readStatus(param string) bool {
+	data := []byte{0}
+	d.bus.ReadRegister(d.Address, APDS9960_STATUS_REG, data)
+
+	switch param {
+	case "CPSAT":
+		return data[0]>>7&0x01 == 1
+	case "PGSAT":
+		return data[0]>>6&0x01 == 1
+	case "PINT":
+		return data[0]>>5&0x01 == 1
+	case "AINT":
+		return data[0]>>4&0x01 == 1
+	case "PVALID":
+		return data[0]>>1&0x01 == 1
+	case "AVALID":
+		return data[0]&0x01 == 1
+	default:
+		return false
+	}
+}
+
+func getPulseLength(l uint8) uint8 {
+	switch l {
+	case 4:
+		return 0
+	case 8:
+		return 1
+	case 16:
+		return 2
+	case 32:
+		return 3
+	default:
+		return 0
+	}
+}
+
+func getPulseCount(c uint8) uint8 {
+	if c < 1 && c > 64 {
+		return 0
+	}
+	return c - 1
+}
+
+func getProximityGain(g uint8) uint8 {
+	switch g {
+	case 1:
+		return 0
+	case 2:
+		return 1
+	case 4:
+		return 2
+	case 8:
+		return 3
+	default:
+		return 0
+	}
+}
+
+func getALSGain(g uint8) uint8 {
+	switch g {
+	case 1:
+		return 0
+	case 4:
+		return 1
+	case 16:
+		return 2
+	case 64:
+		return 3
+	default:
+		return 0
+	}
+}

apds9960/apds9960_generic.go

@@ -0,0 +1,12 @@
+//go:build !nano_33_ble
+// +build !nano_33_ble
+
+package apds9960
+
+import "tinygo.org/x/drivers"
+
+// Configure sets up the APDS-9960 device.
+func (d *Device) Configure(cfg Configuration) {
+	// configure device
+	d.configureDevice(cfg)
+}

apds9960/apds9960_nano_33_ble.go

@@ -0,0 +1,24 @@
+//go:build nano_33_ble
+// +build nano_33_ble
+
+package apds9960
+
+import (
+	"machine"
+	"time"
+)
+
+// Configure sets up the APDS-9960 device.
+func (d *Device) Configure(cfg Configuration) {
+
+	// Following lines are Nano 33 BLE specific, they have nothing to do with sensor per se
+	machine.LSM_PWR.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.LSM_PWR.High()
+	machine.I2C_PULLUP.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.I2C_PULLUP.High()
+	// Wait a moment
+	time.Sleep(10 * time.Millisecond)
+
+	// configure device
+	d.configureDevice(cfg)
+}

apds9960/registers.go

@@ -0,0 +1,78 @@
+package apds9960
+
+const (
+
+	// I2C address
+	ADPS9960_ADDRESS = 0x39
+
+	// control/status registers
+	APDS9960_RAM_REG        = 0x00
+	APDS9960_ENABLE_REG     = 0x80
+	APDS9960_ATIME_REG      = 0x81
+	APDS9960_WTIME_REG      = 0x83
+	APDS9960_AILTIL_REG     = 0x84
+	APDS9960_AILTH_REG      = 0x85
+	APDS9960_AIHTL_REG      = 0x86
+	APDS9960_AIHTH_REG      = 0x87
+	APDS9960_PILT_REG       = 0x89
+	APDS9960_PIHT_REG       = 0x8B
+	APDS9960_PERS_REG       = 0x8C
+	APDS9960_CONFIG1_REG    = 0x8D
+	APDS9960_PPULSE_REG     = 0x8E
+	APDS9960_CONTROL_REG    = 0x8F
+	APDS9960_CONFIG2_REG    = 0x90
+	APDS9960_ID_REG         = 0x92
+	APDS9960_STATUS_REG     = 0x93
+	APDS9960_CDATAL_REG     = 0x94
+	APDS9960_CDATAH_REG     = 0x95
+	APDS9960_RDATAL_REG     = 0x96
+	APDS9960_RDATAH_REG     = 0x97
+	APDS9960_GDATAL_REG     = 0x98
+	APDS9960_GDATAH_REG     = 0x99
+	APDS9960_BDATAL_REG     = 0x9A
+	APDS9960_BDATAH_REG     = 0x9B
+	APDS9960_PDATA_REG      = 0x9C
+	APDS9960_POFFSET_UR_REG = 0x9D
+	APDS9960_POFFSET_DL_REG = 0x9E
+	APDS9960_CONFIG3_REG    = 0x9F
+	APDS9960_GPENTH_REG     = 0xA0
+	APDS9960_GEXTH_REG      = 0xA1
+	APDS9960_GCONF1_REG     = 0xA2
+	APDS9960_GCONF2_REG     = 0xA3
+	APDS9960_GOFFSET_U_REG  = 0xA4
+	APDS9960_GOFFSET_D_REG  = 0xA5
+	APDS9960_GOFFSET_L_REG  = 0xA7
+	APDS9960_GOFFSET_R_REG  = 0xA9
+	APDS9960_GPULSE_REG     = 0xA6
+	APDS9960_GCONF3_REG     = 0xAA
+	APDS9960_GCONF4_REG     = 0xAB
+	APDS9960_GFLVL_REG      = 0xAE
+	APDS9960_GSTATUS_REG    = 0xAF
+	APDS9960_IFORCE_REG     = 0xE4
+	APDS9960_PICLEAR_REG    = 0xE5
+	APDS9960_CICLEAR_REG    = 0xE6
+	APDS9960_AICLEAR_REG    = 0xE7
+	APDS9960_GFIFO_U_REG    = 0xFC
+	APDS9960_GFIFO_D_REG    = 0xFD
+	APDS9960_GFIFO_L_REG    = 0xFE
+	APDS9960_GFIFO_R_REG    = 0xFF
+)
+
+const (
+
+	// sensor modes
+	MODE_NONE = iota
+	MODE_PROXIMITY
+	MODE_COLOR
+	MODE_GESTURE
+)
+
+const (
+
+	// detected gestures
+	GESTURE_NONE = iota
+	GESTURE_UP
+	GESTURE_DOWN
+	GESTURE_LEFT
+	GESTURE_RIGHT
+)

axp192/axp192.go

@@ -0,0 +1,258 @@
+// Package axp192 provides a driver for the axp192 I2C Enhanced single Cell
+// Li-Battery and Power System Management IC.
+//
+// http://www.x-powers.com/en.php/Info/product_detail/article_id/29
+// Datasheet: https://github.com/m5stack/M5-Schematic/blob/master/Core/AXP192%20Datasheet_v1.1_en_draft_2211.pdf
+//
+package axp192 // import "tinygo.org/x/drivers/axp192"
+
+import (
+	"tinygo.org/x/drivers"
+)
+
+type Error uint8
+
+const (
+	ErrInvalidID Error = 0x1
+)
+
+func (e Error) Error() string {
+	switch e {
+	case ErrInvalidID:
+		return "Invalid chip ID"
+	default:
+		return "Unknown error"
+	}
+}
+
+type Device struct {
+	bus     drivers.I2C
+	buf     []byte
+	Address uint8
+}
+
+// New returns AXP192 device for the provided I2C bus using default address.
+func New(i2c drivers.I2C) *Device {
+	return &Device{
+		bus:     i2c,
+		buf:     make([]byte, 2),
+		Address: Address,
+	}
+}
+
+type Config struct {
+}
+
+// Configure the AXP192 device.
+func (d *Device) Configure(config Config) error {
+	return nil
+}
+
+// ReadPowerSupplyStatus reads power supply status.
+func (d *Device) ReadPowerSupplyStatus() uint8 {
+	return d.read8bit(RegPowerSupplyStatus)
+}
+
+// SetVbusIPSOutAccessManagement sets VBUS-IPSOUT access management.
+func (d *Device) SetVbusIPSOutAccessManagement(a uint8) {
+	d.write1Byte(RegVbusIPSOutAccessManagement, a)
+}
+
+// GetVbusIPSOutAccessManagement gets VBUS-IPSOUT access management.
+func (d *Device) GetVbusIPSOutAccessManagement() uint8 {
+	return d.read8bit(RegVbusIPSOutAccessManagement)
+}
+
+// SetGPIO1Control sets GPIO1 function.
+func (d *Device) SetGPIO1Control(a uint8) {
+	d.write1Byte(RegGPIO1Control, a)
+}
+
+// GetGPIO1Control gets GPIO1 function.
+func (d *Device) GetGPIO1Control() uint8 {
+	return d.read8bit(RegGPIO1Control)
+}
+
+// SetGPIO2Control sets GPIO2 function.
+func (d *Device) SetGPIO2Control(a uint8) {
+	d.write1Byte(RegGPIO2Control, a)
+}
+
+// GetGPIO2Control gets GPIO2 function.
+func (d *Device) GetGPIO2Control() uint8 {
+	return d.read8bit(RegGPIO2Control)
+}
+
+// SetGPIO20SignalStatus sets GPIO[2:0] signal status.
+func (d *Device) SetGPIO20SignalStatus(a uint8) {
+	d.write1Byte(RegGPIO20SignalStatus, a)
+}
+
+// GetGPIO20SignalStatus gets GPIO[2:0] signal status.
+func (d *Device) GetGPIO20SignalStatus() uint8 {
+	return d.read8bit(RegGPIO20SignalStatus)
+}
+
+// SetBackupBatteryChargingControl sets backup battery charge control.
+func (d *Device) SetBackupBatteryChargingControl(a uint8) {
+	d.write1Byte(RegBackupBatteryChargingControl, a)
+}
+
+// GetBackupBatteryChargingControl gets backup battery charge control.
+func (d *Device) GetBackupBatteryChargingControl() uint8 {
+	return d.read8bit(RegBackupBatteryChargingControl)
+}
+
+// SetDCDC1VoltageSet sets DC-DC1 output voltage.
+func (d *Device) SetDCDC1VoltageSet(a uint8) {
+	d.write1Byte(RegDCDC1VoltageSet, a)
+}
+
+// GetDCDC1VoltageSet gets DC-DC1 output voltage.
+func (d *Device) GetDCDC1VoltageSet() uint8 {
+	return d.read8bit(RegDCDC1VoltageSet)
+}
+
+// SetDCDC2VoltageSet sets DC-DC2 dynamic voltage parameter.
+func (d *Device) SetDCDC2VoltageSet(a uint8) {
+	d.write1Byte(RegDCDC2VoltageSet, a)
+}
+
+// GetDCDC2VoltageSet gets DC-DC2 dynamic voltage parameter.
+func (d *Device) GetDCDC2VoltageSet() uint8 {
+	return d.read8bit(RegDCDC2VoltageSet)
+}
+
+// SetDCDC3VoltageSet sets DC-DC3 output voltage.
+func (d *Device) SetDCDC3VoltageSet(a uint8) {
+	d.write1Byte(RegDCDC3VoltageSet, a)
+}
+
+// GetDCDC3VoltageSet gets DC-DC3 output voltage.
+func (d *Device) GetDCDC3VoltageSet() uint8 {
+	return d.read8bit(RegDCDC3VoltageSet)
+}
+
+// SetLDO23VoltageSet sets LDO2/3 output voltage.
+func (d *Device) SetLDO23VoltageSet(a uint8) {
+	d.write1Byte(RegLDO23VoltageSet, a)
+}
+
+// GetLDO23VoltageSet gets LDO2/3 output voltage.
+func (d *Device) GetLDO23VoltageSet() uint8 {
+	return d.read8bit(RegLDO23VoltageSet)
+}
+
+// SetDCDC13LDO23Switch sets DC-DC1/3 & LOD2/3 output control.
+func (d *Device) SetDCDC13LDO23Switch(a uint8) {
+	d.write1Byte(RegDCDC13LDO23Switch, a)
+}
+
+// GetDCDC13LDO23Switch gets DC-DC1/3 & LOD2/3 output control.
+func (d *Device) GetDCDC13LDO23Switch() uint8 {
+	return d.read8bit(RegDCDC13LDO23Switch)
+}
+
+// SetGPIO43FunctionControl sets GPIO[4:3] pin function.
+func (d *Device) SetGPIO43FunctionControl(a uint8) {
+	d.write1Byte(RegGPIO43FunctionControl, a)
+}
+
+// GetGPIO43FunctionControl gets GPIO[4:3] pin function.
+func (d *Device) GetGPIO43FunctionControl() uint8 {
+	return d.read8bit(RegGPIO43FunctionControl)
+}
+
+// SetPEKParameterSet sets PEK press key parameter.
+func (d *Device) SetPEKParameterSet(a uint8) {
+	d.write1Byte(RegPEKParameterSet, a)
+}
+
+// GetPEKParameterSet gets PEK press key parameter.
+func (d *Device) GetPEKParameterSet() uint8 {
+	return d.read8bit(RegPEKParameterSet)
+}
+
+// SetADCEnableSet sets ADC enable 1.
+func (d *Device) SetADCEnableSet(a uint8) {
+	d.write1Byte(RegADCEnableSet, a)
+}
+
+// GetADCEnableSet gets ADC enable 1.
+func (d *Device) GetADCEnableSet() uint8 {
+	return d.read8bit(RegADCEnableSet)
+}
+
+// SetGPIO43SignalStatus sets GPIO[4:3] signal status.
+func (d *Device) SetGPIO43SignalStatus(a uint8) {
+	d.write1Byte(RegGPIO43SignalStatus, a)
+}
+
+// GetGPIO43SignalStatus gets GPIO[4:3] signal status.
+func (d *Device) GetGPIO43SignalStatus() uint8 {
+	return d.read8bit(RegGPIO43SignalStatus)
+}
+
+// SetDCVoltage sets DC voltage.
+func (d *Device) SetDCVoltage(number uint8, voltage uint16) {
+	if voltage < 700 {
+		voltage = 0
+	} else {
+		voltage = (voltage - 700) / 25
+	}
+
+	switch number {
+	case 0:
+		v := d.GetDCDC1VoltageSet()
+		d.SetDCDC1VoltageSet((v & 0x80) | (uint8(voltage) & 0x7F))
+	case 1:
+		v := d.GetDCDC2VoltageSet()
+		d.SetDCDC2VoltageSet((v & 0x80) | (uint8(voltage) & 0x7F))
+	case 2:
+		v := d.GetDCDC3VoltageSet()
+		d.SetDCDC3VoltageSet((v & 0x80) | (uint8(voltage) & 0x7F))
+	}
+}
+
+// SetLDOVoltage sets LDO voltage.
+func (d *Device) SetLDOVoltage(number uint8, voltage uint16) {
+	if voltage > 3300 {
+		voltage = 15
+	} else {
+		voltage = (voltage / 100) - 18
+	}
+
+	switch number {
+	case 2:
+		v := d.GetLDO23VoltageSet()
+		d.SetLDO23VoltageSet((v & 0x0F) | (uint8(voltage) << 4))
+		break
+	case 3:
+		v := d.GetLDO23VoltageSet()
+		d.SetLDO23VoltageSet((v & 0xF0) | uint8(voltage))
+		break
+	}
+}
+
+// SetLDOEnable enable LDO.
+func (d *Device) SetLDOEnable(number uint8, state bool) {
+	mark := uint8(0x01)
+	mark <<= number
+	switch number {
+	case 2:
+		v := d.GetDCDC13LDO23Switch()
+		d.SetDCDC13LDO23Switch(v | mark)
+	case 3:
+		v := d.GetDCDC13LDO23Switch()
+		d.SetDCDC13LDO23Switch(v & (^mark))
+	}
+}
+
+func (d *Device) write1Byte(reg, data uint8) {
+	d.bus.WriteRegister(d.Address, reg, []byte{data})
+}
+
+func (d *Device) read8bit(reg uint8) uint8 {
+	d.bus.ReadRegister(d.Address, reg, d.buf[:1])
+	return d.buf[0]
+}

axp192/m5stack-core2-axp192/axp192.go

@@ -0,0 +1,158 @@
+package axp192
+
+import (
+	"time"
+
+	"tinygo.org/x/drivers"
+	axp192orig "tinygo.org/x/drivers/axp192"
+)
+
+// Device wraps an I2C connection to a AXP192 device.
+type Device struct {
+	*axp192orig.Device
+	LED    Pin
+	RST    Pin
+	SPK_EN Pin
+}
+
+// New creates a new AXP192 connection. The I2C bus must already be
+// configured.
+//
+// This function only creates the Device object, it does not touch the device.
+func New(i2c drivers.I2C) *Device {
+	d := axp192orig.New(i2c)
+
+	axp := &Device{
+		Device: d,
+	}
+	axp.LED = Pin{pin: 1, axp: axp}
+	axp.SPK_EN = Pin{pin: 2, axp: axp}
+	axp.RST = Pin{pin: 4, axp: axp}
+
+	axp.begin()
+
+	return axp
+}
+
+type Config struct {
+}
+
+// Configure sets up the device for communication
+func (d *Device) Configure(config Config) error {
+	return d.Device.Configure(axp192orig.Config{})
+}
+
+func (d *Device) begin() {
+	d.SetVbusIPSOutAccessManagement((d.GetVbusIPSOutAccessManagement() & 0x04) | 0x02)
+	d.SetGPIO1Control(d.GetGPIO1Control() & 0xF8)
+	d.SetGPIO2Control(d.GetGPIO2Control() & 0xF8)
+	d.SetBackupBatteryChargingControl((d.GetBackupBatteryChargingControl() & 0x1C) | 0xA2)
+	d.SetESPVoltage(3350)
+	d.SetLcdVoltage(3300)
+	d.SetLDOVoltage(2, 3300) //Periph power voltage preset (LCD_logic, SD card)
+	d.SetLDOVoltage(3, 2000) //Vibrator power voltage preset
+
+	d.SetLDOEnable(2, true)
+	d.SetDCDC3(true) // LCD Backlight
+	// GPIO4 : LCD Reset
+	d.SetGPIO43FunctionControl((d.GetGPIO43FunctionControl() & 0x72) | 0x84)
+	// Power On/Off Setting
+	d.SetPEKParameterSet(0x4C)
+	d.SetADCEnableSet(0xFF)
+
+	d.RST.Low()
+	time.Sleep(100 * time.Millisecond)
+	d.RST.High()
+	time.Sleep(100 * time.Millisecond)
+}
+
+// ToggleLED toggles LED connected to AXP192.
+func (d *Device) ToggleLED() {
+	v := d.GetGPIO20SignalStatus()
+	if (v & 0x02) > 0 {
+		d.SetGPIO20SignalStatus(v & 0xFD)
+	} else {
+		d.SetGPIO20SignalStatus(v | 0x02)
+	}
+}
+
+// SetESPVoltage sets voltage of ESP32.
+func (d *Device) SetESPVoltage(voltage uint16) {
+	if voltage >= 3000 && voltage <= 3400 {
+		d.SetDCVoltage(0, voltage)
+	}
+}
+
+// SetLcdVoltage sets voltage of LCD.
+func (d *Device) SetLcdVoltage(voltage uint16) {
+	if voltage >= 2500 && voltage <= 3300 {
+		d.SetDCVoltage(2, voltage)
+	}
+}
+
+// SetDCDC3 enables or disables DCDC3.
+func (d *Device) SetDCDC3(State bool) {
+	v := d.GetDCDC13LDO23Switch()
+	if State == true {
+		v = (1 << 1) | v
+	} else {
+		v = ^(uint8(1) << 1) & v
+	}
+	d.SetDCDC13LDO23Switch(v)
+}
+
+// Pin is a single pin on AXP192.
+type Pin struct {
+	pin uint8
+	axp *Device
+}
+
+// High sets this GPIO pin to high.
+func (p Pin) High() {
+	switch p.pin {
+	case 1: // LED
+		v := p.axp.GetGPIO20SignalStatus()
+		p.axp.SetGPIO20SignalStatus(v | 0x02)
+	case 2: // SPK_EN
+	case 4: // RST
+		v := p.axp.GetGPIO43SignalStatus()
+		v |= uint8(0x02)
+		p.axp.SetGPIO43SignalStatus(v)
+	}
+}
+
+// Low sets this GPIO pin to low.
+func (p Pin) Low() {
+	switch p.pin {
+	case 1: // LED
+		v := p.axp.GetGPIO20SignalStatus()
+		p.axp.SetGPIO20SignalStatus(v & 0xFD)
+	case 2: // SPK_EN
+	case 4: // RST
+		v := p.axp.GetGPIO43SignalStatus()
+		v &= ^uint8(0x02)
+		p.axp.SetGPIO43SignalStatus(v)
+	}
+}
+
+// Toggle switches an output pin from low to high or from high to low.
+func (p Pin) Toggle() {
+	switch p.pin {
+	case 1: // LED
+		v := p.axp.GetGPIO20SignalStatus()
+		if (v & 0x02) == 0 {
+			p.axp.SetGPIO20SignalStatus(v | 0x02)
+		} else {
+			p.axp.SetGPIO20SignalStatus(v & 0xFD)
+		}
+	case 2: // SPK_EN
+	case 4: // RST
+		v := p.axp.GetGPIO43SignalStatus()
+		if (v & 0x02) == 0 {
+			v |= uint8(0x02)
+		} else {
+			v &= ^uint8(0x02)
+		}
+		p.axp.SetGPIO43SignalStatus(v)
+	}
+}

axp192/registers.go

@@ -0,0 +1,127 @@
+package axp192
+
+// power supply control class
+// 0x00 Power supply status register
+// 0x01  Power supply mode/charging status register
+// 0x04  OTG VBUS status register
+// 0x06‐09  Data buffer register
+// 0x10  EXTEN & DC‐DC2 switch register
+// 0x12  DC‐DC1/3 & LDO2/3switch register
+// 0x23  DC‐DC2 voltage set register
+// 0x25  DC‐DC2 voltage slope set register
+// 0x26  DC‐DC1voltage set register
+// 0x27  DC‐DC3 voltage set register
+// 0x28  LDO2/3 voltage set register
+// 0x30  VBUS‐IPSOUT access set register
+// 0x31  VOFF power off voltage set register
+// 0x32  Power off、battery detect、CHGLED control register
+// 0x33  Charging control register1
+// 0x34  Charging control register2
+// 0x35  Backup battery charging control register
+// 0x36  PEK parameter set register
+// 0x37  DCDC switch frequency set register
+// 0x38  Battery charging under temperature warning set register
+// 0x39  Battery charging over temperature warning set register
+// 0x3A  APS under voltage Level1 set register
+// 0x3B  APS under voltage Level2 set register
+// 0x3C  Battery discharging under temperature warning set register
+// 0x3D  Battery discharging over temperature warning set register
+// 0x80  DCDC mode set register
+// 0x82  ADC enable set register 1
+// 0x83  ADC enable set register 2
+// 0x84  ADC sample frequency set, TS pin control register
+// 0x85  GPIO [3:0] input range set register
+// 0x8A  Timer control register
+// 0x8B  VBUS monitor set register
+// 0x8F  Over temperature power off control register
+
+// GPIO control class
+// 0x90  GPIO0 control register
+// 0x91  GPIO0 LDO mode output voltage set register
+// 0x92  GPIO1 control register
+// 0x93  GPIO2 control register
+// 0x94  GPIO[2:0] signal status register
+// 0x95  GPIO[4:3] function control register
+// 0x96  GPIO[4:3] signal status register
+// 0x97  GPIO[2:0] pull down control register
+// 0x98  PWM1 frequency set register
+// 0x99  PWM1 duty ratio set register 1
+// 0x9A  PWM1 duty ratio set register 2
+// 0x9B  PWM2 frequency set register
+// 0x9C  PWM2 duty ratio set register 1
+// 0x9D  PWM2 duty ratio set register 2
+// 0x9E  GPIO5 control register
+
+// IRQ control class
+// 0x40  IRQ enable control register 1
+// 0x41  IRQ enable control register 2
+// 0x42  IRQ enable control register 3
+// 0x43  IRQ enable control register 4
+// 0x44  IRQ status register 1
+// 0x45  IRQ status register 2
+// 0x46  IRQ status register 3
+// 0x47  IRQ status register 4
+
+// ADC data class
+// 0x56  ACIN voltage ADC data high 8 bit
+// 0x57  ACIN voltage ADC data low 4 bit
+// 0x58  ACIN current ADC data high 8 bit
+// 0x59  ACIN current ADC data low 4 bit
+// 0x5A  VBUS voltage ADC data high 8 bit
+// 0x5B  VBUS voltage ADC data low 4 bit
+// 0x5C  VBUS current ADC data high 8 bit
+// 0x5D  VBUS current ADC data low 4 bit
+// 0x5E  AXP192 internal temperature monitor ADC data High 8 bit
+// 0x5F  AXP192 internal temperature monitor ADC data low 4 bit
+// 0x62  TS input ADC data High 8 bit，monitor battery temperature by default
+// 0x63  TS input ADC data low 4 bit，monitor battery temperature by default
+// 0x64  GPIO0 voltage ADC data high 8 bit
+// 0x65  GPIO0 voltage ADC data low 4 bit
+// 0x66  GPIO1 voltage ADC data high 8 bit
+// 0x67  GPIO1 voltage ADC data low 4 bit
+// 0x68  GPIO2 voltage ADC data high 8 bit
+// 0x69  GPIO2 voltage ADC data low 4 bit
+// 0x6A  GPIO[3] voltage ADC data high 8 bit
+// 0x6B  GPIO[3] voltage ADC data low 4 bit
+// 0x70  Battery instantaneous power high 8 bit
+// 0x71  Battery instantaneous power middle 8 bit
+// 0x72  Battery instantaneous power low 8 bit
+// 0x78  Battery voltage high 8 bit
+// 0x79  Battery voltage low 4 bit
+// 0x7A  Battery charging current high 8 bit
+// 0x7B  Battery charging current low 5 bit
+// 0x7C  Battery discharging current high 8 bit
+// 0x7D  Battery discharging current low 5 bit
+// 0x7E  APS voltage high 8 bit
+// 0x7F  APS voltage low 4 bit
+// 0xB0  Battery charging coulomb counter data register 3
+// 0xB1  Battery charging coulomb counter data register 2
+// 0xB2  Battery charging coulomb counter data register 1
+// 0xB3  Battery charging coulomb counter data register 0
+// 0xB4  Battery discharging coulomb counter data register 3
+// 0xB5  Battery discharging coulomb counter data register 2
+// 0xB6  Battery discharging coulomb counter data register 1
+// 0xB7  Battery discharging coulomb counter data register 0
+// 0xB8  Coulomb counter control register
+
+const (
+	// Address is default I2C address.
+	Address = 0x34
+
+	RegPowerSupplyStatus            = 0x00
+	RegDCDC13LDO23Switch            = 0x12
+	RegVbusIPSOutAccessManagement   = 0x30
+	RegBackupBatteryChargingControl = 0x35
+	RegDCDC2VoltageSet              = 0x25
+	RegDCDC1VoltageSet              = 0x26
+	RegDCDC3VoltageSet              = 0x27
+	RegLDO23VoltageSet              = 0x28
+	RegPEKParameterSet              = 0x36
+	RegADCEnableSet                 = 0x82
+
+	RegGPIO1Control          = 0x92
+	RegGPIO2Control          = 0x93
+	RegGPIO20SignalStatus    = 0x94
+	RegGPIO43FunctionControl = 0x95
+	RegGPIO43SignalStatus    = 0x96
+)

cmd/convert2bin/convert2bin.go

@@ -0,0 +1,49 @@
+package main
+
+import (
+	"fmt"
+	"io/ioutil"
+	"log"
+	"os"
+	"strings"
+)
+
+// See ../../image/README.md for the usage.
+
+func main() {
+	err := run(os.Args)
+	if err != nil {
+		log.Fatal(err)
+	}
+}
+
+func run(args []string) error {
+	if len(args) < 2 {
+		return fmt.Errorf("usage: %s FILE")
+	}
+
+	b, err := ioutil.ReadFile(args[1])
+	if err != nil {
+		return err
+	}
+
+	fmt.Printf("const %s = \"\" +\n", strings.Replace(args[1], ".", "_", -1))
+
+	i := 0
+	max := 32
+	for i = 0; i < len(b); i++ {
+		bb := b[i]
+		if (i % max) == 0 {
+			fmt.Printf("	\"")
+		}
+		fmt.Printf("\\x%02X", bb)
+		if (i%max) == max-1 && i != len(b)-1 {
+			fmt.Printf("\" + \n")
+		}
+	}
+	if (i % max) < max-1 {
+		fmt.Printf("\"\n")
+	}
+
+	return nil
+}

dht/highfreq.go

@@ -1,4 +1,5 @@
-// +build mimxrt1062  stm32f405  atsamd51  stm32f103xx  k210  stm32f407
+//go:build mimxrt1062 || stm32f405 || atsamd51 || stm32f103xx || k210 || stm32f407
+// +build mimxrt1062 stm32f405 atsamd51 stm32f103xx k210 stm32f407
 
 package dht // import "tinygo.org/x/drivers/dht"
 

dht/lowfreq.go

@@ -1,4 +1,5 @@
-// +build arduino atmega1284p nrf52840 digispark nrf52 arduino_nano nrf51 atsamd21 fe310 arduino_nano33 circuitplay_express arduino_mega2560
+//go:build !mimxrt1062 && !stm32f405 && !atsamd51 && !stm32f103xx && !k210 && !stm32f407
+// +build !mimxrt1062,!stm32f405,!atsamd51,!stm32f103xx,!k210,!stm32f407
 
 package dht // import "tinygo.org/x/drivers/dht"
 

espat/adapter.go

@@ -0,0 +1,23 @@
+package espat
+
+import (
+	"time"
+
+	"tinygo.org/x/drivers/net"
+)
+
+func (d *Device) ConnectToAccessPoint(ssid, pass string, timeout time.Duration) error {
+	if len(ssid) == 0 {
+		return net.ErrWiFiMissingSSID
+	}
+
+	if err := d.SetWifiMode(WifiModeClient); err != nil {
+		return err
+	}
+
+	return d.ConnectToAP(ssid, pass, 10)
+}
+
+func (d *Device) Disconnect() error {
+	return d.DisconnectFromAP()
+}

espat/espat.go

@@ -28,6 +28,8 @@ import (
 	"tinygo.org/x/drivers/net"
 )
 
+const CRLF = "\r\n"
+
 // Device wraps UART connection to the ESP8266/ESP32.
 type Device struct {
 	bus drivers.UART
@@ -37,10 +39,10 @@ type Device struct {
 
 	// data received from a TCP/UDP connection forwarded by the ESP8266/ESP32
 	socketdata []byte
-}
 
-// ActiveDevice is the currently configured Device in use. There can only be one.
-var ActiveDevice *Device
+	// dump extra data to console?
+	Debug bool
+}
 
 // New returns a new espat driver. Pass in a fully configured UART bus.
 func New(b drivers.UART) *Device {
@@ -48,9 +50,9 @@ func New(b drivers.UART) *Device {
 }
 
 // Configure sets up the device for communication.
-func (d Device) Configure() {
-	ActiveDevice = &d
-	net.ActiveDevice = ActiveDevice
+func (d *Device) Configure() {
+	// set the configured Device in use. There can only be one.
+	net.UseDriver(d)
 }
 
 // Connected checks if there is communication with the ESP8266/ESP32.
@@ -59,10 +61,7 @@ func (d *Device) Connected() bool {
 
 	// handle response here, should include "OK"
 	_, err := d.Response(100)
-	if err != nil {
-		return false
-	}
-	return true
+	return err == nil
 }
 
 // Write raw bytes to the UART.
@@ -80,21 +79,33 @@ const pause = 300
 
 // Execute sends an AT command to the ESP8266/ESP32.
 func (d Device) Execute(cmd string) error {
-	_, err := d.Write([]byte("AT" + cmd + "\r\n"))
+	data := "AT" + cmd
+	if d.Debug {
+		debugprintln(data)
+	}
+	_, err := d.Write([]byte(data + CRLF))
 	return err
 }
 
 // Query sends an AT command to the ESP8266/ESP32 that returns the
 // current value for some configuration parameter.
 func (d Device) Query(cmd string) (string, error) {
-	_, err := d.Write([]byte("AT" + cmd + "?\r\n"))
+	data := "AT" + cmd + "?"
+	if d.Debug {
+		debugprintln(data)
+	}
+	_, err := d.Write([]byte(data + CRLF))
 	return "", err
 }
 
 // Set sends an AT command with params to the ESP8266/ESP32 for a
 // configuration value to be set.
 func (d Device) Set(cmd, params string) error {
-	_, err := d.Write([]byte("AT" + cmd + "=" + params + "\r\n"))
+	data := "AT" + cmd + "=" + params
+	if d.Debug {
+		debugprintln(data)
+	}
+	_, err := d.Write([]byte(data + CRLF))
 	return err
 }
 
@@ -103,6 +114,10 @@ func (d Device) Version() []byte {
 	d.Execute(Version)
 	r, err := d.Response(100)
 	if err != nil {
+		if d.Debug {
+			debugprintln(string(r))
+		}
+
 		return []byte("unknown")
 	}
 	return r
@@ -152,17 +167,17 @@ func (d *Device) ReadSocket(b []byte) (n int, err error) {
 // The call will retry for up to timeout milliseconds before returning nothing.
 func (d *Device) Response(timeout int) ([]byte, error) {
 	// read data
-	var size int
 	var start, end int
-	pause := 100 // pause to wait for 100 ms
-	retries := timeout / pause
+	pause := 10 * time.Millisecond
+	starting := time.Now()
 
 	for {
-		size = d.bus.Buffered()
-
-		if size > 0 {
+		if size := d.bus.Buffered(); size > 0 {
 			end += size
-			d.bus.Read(d.response[start:end])
+			_, err := d.bus.Read(d.response[start:end])
+			if err != nil {
+				return nil, err
+			}
 
 			// if "+IPD" then read socket data
 			if strings.Contains(string(d.response[:end]), "+IPD") {
@@ -172,12 +187,15 @@ func (d *Device) Response(timeout int) ([]byte, error) {
 
 			// if "OK" then the command worked
 			if strings.Contains(string(d.response[:end]), "OK") {
-				return d.response[start:end], nil
+				if d.Debug {
+					debugprintln(string(d.response[:end]))
+				}
+				return d.response[:end], nil
 			}
 
 			// if "Error" then the command failed
 			if strings.Contains(string(d.response[:end]), "ERROR") {
-				return d.response[start:end], errors.New("response error:" + string(d.response[start:end]))
+				return d.response[:end], errors.New("response error:" + string(d.response[:end]))
 			}
 
 			// if anything else, then keep reading data in?
@@ -185,12 +203,11 @@ func (d *Device) Response(timeout int) ([]byte, error) {
 		}
 
 		// wait longer?
-		retries--
-		if retries == 0 {
-			return nil, errors.New("response timeout error:" + string(d.response[start:end]))
+		if time.Since(starting) > time.Duration(timeout)*time.Millisecond {
+			return nil, errors.New("response timeout error:" + string(d.response[:end]))
 		}
 
-		time.Sleep(time.Duration(pause) * time.Millisecond)
+		time.Sleep(pause)
 	}
 }
 
@@ -220,3 +237,7 @@ func (d *Device) parseIPD(end int) error {
 func (d *Device) IsSocketDataAvailable() bool {
 	return len(d.socketdata) > 0 || d.bus.Buffered() > 0
 }
+
+func debugprintln(msg string) {
+	println("[DEBUG] " + msg)
+}

espat/tcp.go

@@ -19,6 +19,9 @@ func (d *Device) GetDNS(domain string) (string, error) {
 	d.Set(TCPDNSLookup, "\""+domain+"\"")
 	resp, err := d.Response(1000)
 	if err != nil {
+		if d.Debug {
+			println(string(resp))
+		}
 		return "", err
 	}
 	if !strings.Contains(string(resp), ":") {
@@ -36,13 +39,17 @@ func (d *Device) GetDNS(domain string) (string, error) {
 // Currently only supports single connection mode.
 func (d *Device) ConnectTCPSocket(addr, port string) error {
 	protocol := "TCP"
-	val := "\"" + protocol + "\",\"" + addr + "\"," + port + ",120"
+	val := "\"" + protocol + "\"," + addr + "," + port + ",120"
 	err := d.Set(TCPConnect, val)
 	if err != nil {
 		return err
 	}
-	_, e := d.Response(3000)
+	r, e := d.Response(3000)
 	if e != nil {
+		if d.Debug {
+			println(string(r))
+		}
+
 		return e
 	}
 	return nil
@@ -51,13 +58,17 @@ func (d *Device) ConnectTCPSocket(addr, port string) error {
 // ConnectUDPSocket creates a new UDP connection for the ESP8266/ESP32.
 func (d *Device) ConnectUDPSocket(addr, sendport, listenport string) error {
 	protocol := "UDP"
-	val := "\"" + protocol + "\",\"" + addr + "\"," + sendport + "," + listenport + ",2"
+	val := "\"" + protocol + "\"," + addr + "," + sendport + "," + listenport + ",2"
 	err := d.Set(TCPConnect, val)
 	if err != nil {
 		return err
 	}
-	_, e := d.Response(3000)
+	r, e := d.Response(3000)
 	if e != nil {
+		if d.Debug {
+			println(string(r))
+		}
+
 		return e
 	}
 	return nil
@@ -67,11 +78,15 @@ func (d *Device) ConnectUDPSocket(addr, sendport, listenport string) error {
 // Currently only supports single connection mode.
 func (d *Device) ConnectSSLSocket(addr, port string) error {
 	protocol := "SSL"
-	val := "\"" + protocol + "\",\"" + addr + "\"," + port + ",120"
+	val := "\"" + protocol + "\"," + addr + "," + port + ",120"
 	d.Set(TCPConnect, val)
 	// this operation takes longer, so wait up to 6 seconds to complete.
-	_, err := d.Response(6000)
+	r, err := d.Response(6000)
 	if err != nil {
+		if d.Debug {
+			println(string(r))
+		}
+
 		return err
 	}
 	return nil
@@ -83,8 +98,12 @@ func (d *Device) DisconnectSocket() error {
 	if err != nil {
 		return err
 	}
-	_, e := d.Response(pause)
+	r, e := d.Response(pause)
 	if e != nil {
+		if d.Debug {
+			println(string(r))
+		}
+
 		return e
 	}
 	return nil
@@ -95,7 +114,11 @@ func (d *Device) DisconnectSocket() error {
 func (d *Device) SetMux(mode int) error {
 	val := strconv.Itoa(mode)
 	d.Set(TCPMultiple, val)
-	_, err := d.Response(pause)
+	r, err := d.Response(pause)
+	if err != nil && d.Debug {
+		println(string(r))
+	}
+
 	return err
 }
 
@@ -110,7 +133,11 @@ func (d *Device) GetMux() ([]byte, error) {
 func (d *Device) SetTCPTransferMode(mode int) error {
 	val := strconv.Itoa(mode)
 	d.Set(TransmissionMode, val)
-	_, err := d.Response(pause)
+	r, err := d.Response(pause)
+	if err != nil && d.Debug {
+		println(string(r))
+	}
+
 	return err
 }
 
@@ -123,12 +150,19 @@ func (d *Device) GetTCPTransferMode() ([]byte, error) {
 // StartSocketSend gets the ESP8266/ESP32 ready to receive TCP/UDP socket data.
 func (d *Device) StartSocketSend(size int) error {
 	val := strconv.Itoa(size)
-	d.Set(TCPSend, val)
+	err := d.Set(TCPSend, val)
+	if err != nil {
+		return err
+	}
 
 	// when ">" is received, it indicates
 	// ready to receive data
-	r, err := d.Response(2000)
+	r, err := d.Response(500)
 	if err != nil {
+		if d.Debug {
+			println(string(r))
+		}
+
 		return err
 	}
 	if strings.Contains(string(r), ">") {
@@ -142,6 +176,10 @@ func (d *Device) StartSocketSend(size int) error {
 func (d *Device) EndSocketSend() error {
 	d.Write([]byte("+++"))
 
-	_, err := d.Response(pause)
+	r, err := d.Response(pause)
+	if err != nil && d.Debug {
+		println(string(r))
+	}
+
 	return err
 }

espat/wifi.go

@@ -25,7 +25,11 @@ func (d *Device) GetWifiMode() ([]byte, error) {
 func (d *Device) SetWifiMode(mode int) error {
 	val := strconv.Itoa(mode)
 	d.Set(WifiMode, val)
-	_, err := d.Response(pause)
+	r, err := d.Response(pause)
+	if err != nil && d.Debug {
+		debugprintln(string(r))
+	}
+
 	return err
 }
 
@@ -43,8 +47,12 @@ func (d *Device) ConnectToAP(ssid, pwd string, ws int) error {
 	val := "\"" + ssid + "\",\"" + pwd + "\""
 	d.Set(ConnectAP, val)
 
-	_, err := d.Response(ws * 1000)
+	r, err := d.Response(ws * 1000)
 	if err != nil {
+		if d.Debug {
+			debugprintln(string(r))
+		}
+
 		return err
 	}
 	return nil
@@ -53,7 +61,11 @@ func (d *Device) ConnectToAP(ssid, pwd string, ws int) error {
 // DisconnectFromAP disconnects the ESP8266/ESP32 from the current access point.
 func (d *Device) DisconnectFromAP() error {
 	d.Execute(Disconnect)
-	_, err := d.Response(1000)
+	r, err := d.Response(1000)
+	if err != nil && d.Debug {
+		debugprintln(string(r))
+	}
+
 	return err
 }
 
@@ -68,7 +80,11 @@ func (d *Device) GetClientIP() (string, error) {
 func (d *Device) SetClientIP(ipaddr string) error {
 	val := "\"" + ipaddr + "\""
 	d.Set(ConnectAP, val)
-	_, err := d.Response(500)
+	r, err := d.Response(500)
+	if err != nil && d.Debug {
+		debugprintln(string(r))
+	}
+
 	return err
 }
 
@@ -78,6 +94,10 @@ func (d *Device) SetClientIP(ipaddr string) error {
 func (d *Device) GetAPConfig() (string, error) {
 	d.Query(SoftAPConfigCurrent)
 	r, err := d.Response(100)
+	if err != nil && d.Debug {
+		debugprintln(string(r))
+	}
+
 	return string(r), err
 }
 
@@ -89,7 +109,11 @@ func (d *Device) SetAPConfig(ssid, pwd string, ch, security int) error {
 	ecnval := strconv.Itoa(security)
 	val := "\"" + ssid + "\",\"" + pwd + "\"," + chval + "," + ecnval
 	d.Set(SoftAPConfigCurrent, val)
-	_, err := d.Response(1000)
+	r, err := d.Response(1000)
+	if err != nil && d.Debug {
+		debugprintln(string(r))
+	}
+
 	return err
 }
 
@@ -97,6 +121,9 @@ func (d *Device) SetAPConfig(ssid, pwd string, ch, security int) error {
 func (d *Device) GetAPClients() (string, error) {
 	d.Query(ListConnectedIP)
 	r, err := d.Response(100)
+	if err != nil && d.Debug {
+		debugprintln(string(r))
+	}
 	return string(r), err
 }
 
@@ -104,6 +131,9 @@ func (d *Device) GetAPClients() (string, error) {
 func (d *Device) GetAPIP() (string, error) {
 	d.Query(SetSoftAPIPCurrent)
 	r, err := d.Response(100)
+	if err != nil && d.Debug {
+		debugprintln(string(r))
+	}
 	return string(r), err
 }
 
@@ -111,7 +141,10 @@ func (d *Device) GetAPIP() (string, error) {
 func (d *Device) SetAPIP(ipaddr string) error {
 	val := "\"" + ipaddr + "\""
 	d.Set(SetSoftAPIPCurrent, val)
-	_, err := d.Response(500)
+	r, err := d.Response(500)
+	if err != nil && d.Debug {
+		debugprintln(string(r))
+	}
 	return err
 }
 
@@ -120,6 +153,9 @@ func (d *Device) SetAPIP(ipaddr string) error {
 func (d *Device) GetAPConfigFlash() (string, error) {
 	d.Query(SoftAPConfigFlash)
 	r, err := d.Response(100)
+	if err != nil && d.Debug {
+		debugprintln(string(r))
+	}
 	return string(r), err
 }
 
@@ -132,7 +168,10 @@ func (d *Device) SetAPConfigFlash(ssid, pwd string, ch, security int) error {
 	ecnval := strconv.Itoa(security)
 	val := "\"" + ssid + "\",\"" + pwd + "\"," + chval + "," + ecnval
 	d.Set(SoftAPConfigFlash, val)
-	_, err := d.Response(1000)
+	r, err := d.Response(1000)
+	if err != nil && d.Debug {
+		debugprintln(string(r))
+	}
 	return err
 }
 
@@ -141,6 +180,9 @@ func (d *Device) SetAPConfigFlash(ssid, pwd string, ch, security int) error {
 func (d *Device) GetAPIPFlash() (string, error) {
 	d.Query(SetSoftAPIPFlash)
 	r, err := d.Response(100)
+	if err != nil && d.Debug {
+		debugprintln(string(r))
+	}
 	return string(r), err
 }
 
@@ -149,6 +191,9 @@ func (d *Device) GetAPIPFlash() (string, error) {
 func (d *Device) SetAPIPFlash(ipaddr string) error {
 	val := "\"" + ipaddr + "\""
 	d.Set(SetSoftAPIPFlash, val)
-	_, err := d.Response(500)
+	r, err := d.Response(500)
+	if err != nil && d.Debug {
+		debugprintln(string(r))
+	}
 	return err
 }

examples/apds9960/color/main.go

@@ -0,0 +1,39 @@
+package main
+
+import (
+	"machine"
+	"time"
+
+	"tinygo.org/x/drivers/apds9960"
+)
+
+func main() {
+
+	// use Nano 33 BLE Sense's internal I2C bus
+	machine.I2C1.Configure(machine.I2CConfig{
+		SCL:       machine.SCL1_PIN,
+		SDA:       machine.SDA1_PIN,
+		Frequency: machine.TWI_FREQ_400KHZ,
+	})
+
+	sensor := apds9960.New(machine.I2C1)
+
+	sensor.Configure(apds9960.Configuration{}) // use default settings
+
+	if !sensor.Connected() {
+		println("APDS-9960 not connected!")
+		return
+	}
+
+	sensor.EnableColor() // enable color engine
+
+	for {
+
+		if sensor.ColorAvailable() {
+			r, g, b, c := sensor.ReadColor()
+			println("Red =", r, "\tGreen =", g, "\tBlue =", b, "\tClear =", c)
+		}
+		time.Sleep(time.Millisecond * 100)
+	}
+
+}

examples/apds9960/gesture/main.go

@@ -0,0 +1,52 @@
+package main
+
+import (
+	"machine"
+	"time"
+
+	"tinygo.org/x/drivers/apds9960"
+)
+
+func main() {
+
+	// use Nano 33 BLE Sense's internal I2C bus
+	machine.I2C1.Configure(machine.I2CConfig{
+		SCL:       machine.SCL1_PIN,
+		SDA:       machine.SDA1_PIN,
+		Frequency: machine.TWI_FREQ_400KHZ,
+	})
+
+	sensor := apds9960.New(machine.I2C1)
+
+	sensor.Configure(apds9960.Configuration{}) // use default settings
+
+	if !sensor.Connected() {
+		println("APDS-9960 not connected!")
+		return
+	}
+
+	sensor.EnableGesture() // enable gesture engine
+
+	for {
+
+		// wave your hand (not too slow) about 10 cm above the sensor
+		if sensor.GestureAvailable() {
+
+			gesture := sensor.ReadGesture()
+			print("Detected gesture: ")
+			switch gesture {
+			case apds9960.GESTURE_UP: // the nRF52 chip is "up"
+				println("Up")
+			case apds9960.GESTURE_DOWN:
+				println("Down")
+			case apds9960.GESTURE_LEFT:
+				println("Left")
+			case apds9960.GESTURE_RIGHT:
+				println("Right")
+			}
+		}
+		// note: the delay shouldn't be too long, otherwise new gesture data might be lost
+		time.Sleep(time.Millisecond * 250)
+	}
+
+}

examples/apds9960/proximity/main.go

@@ -0,0 +1,40 @@
+package main
+
+import (
+	"machine"
+	"time"
+
+	"tinygo.org/x/drivers/apds9960"
+)
+
+func main() {
+
+	// use Nano 33 BLE Sense's internal I2C bus
+	machine.I2C1.Configure(machine.I2CConfig{
+		SCL:       machine.SCL1_PIN,
+		SDA:       machine.SDA1_PIN,
+		Frequency: machine.TWI_FREQ_400KHZ,
+	})
+
+	sensor := apds9960.New(machine.I2C1)
+
+	// use default settings
+	sensor.Configure(apds9960.Configuration{})
+
+	if !sensor.Connected() {
+		println("APDS-9960 not connected!")
+		return
+	}
+
+	sensor.EnableProximity() // enable proximity engine
+
+	for {
+
+		if sensor.ProximityAvailable() {
+			p := sensor.ReadProximity()
+			println("Proximity:", p)
+		}
+		time.Sleep(time.Millisecond * 100)
+	}
+
+}

examples/axp192/m5stack-core2-blinky/main.go

@@ -0,0 +1,25 @@
+package main
+
+import (
+	"machine"
+	"time"
+
+	axp192 "tinygo.org/x/drivers/axp192/m5stack-core2-axp192"
+	"tinygo.org/x/drivers/i2csoft"
+)
+
+func main() {
+	i2c := i2csoft.New(machine.SCL0_PIN, machine.SDA0_PIN)
+	i2c.Configure(i2csoft.I2CConfig{Frequency: 100e3})
+
+	axp := axp192.New(i2c)
+	led := axp.LED
+
+	for {
+		led.Low()
+		time.Sleep(time.Millisecond * 500)
+
+		led.High()
+		time.Sleep(time.Millisecond * 500)
+	}
+}

examples/espat/espconsole/main.go

@@ -113,8 +113,9 @@ func connectToESP() bool {
 func connectToAP() {
 	println("Connecting to wifi network '" + ssid + "'")
 
-	adaptor.SetWifiMode(espat.WifiModeClient)
-	adaptor.ConnectToAP(ssid, pass, 10)
+	if err := adaptor.ConnectToAccessPoint(ssid, pass, 10*time.Second); err != nil {
+		failMessage(err.Error())
+	}
 
 	println("Connected.")
 	ip, err := adaptor.GetClientIP()

examples/espat/esphub/main.go

@@ -99,8 +99,9 @@ func connectToESP() bool {
 func connectToAP() {
 	println("Connecting to wifi network '" + ssid + "'")
 
-	adaptor.SetWifiMode(espat.WifiModeClient)
-	adaptor.ConnectToAP(ssid, pass, 10)
+	if err := adaptor.ConnectToAccessPoint(ssid, pass, 10*time.Second); err != nil {
+		failMessage(err.Error())
+	}
 
 	println("Connected.")
 	ip, err := adaptor.GetClientIP()

examples/espat/espstation/main.go

@@ -88,8 +88,9 @@ func connectToESP() bool {
 func connectToAP() {
 	println("Connecting to wifi network '" + ssid + "'")
 
-	adaptor.SetWifiMode(espat.WifiModeClient)
-	adaptor.ConnectToAP(ssid, pass, 10)
+	if err := adaptor.ConnectToAccessPoint(ssid, pass, 10*time.Second); err != nil {
+		failMessage(err.Error())
+	}
 
 	println("Connected.")
 	ip, err := adaptor.GetClientIP()

examples/espat/mqttclient/main.go

@@ -108,8 +108,9 @@ func connectToESP() bool {
 func connectToAP() {
 	println("Connecting to wifi network '" + ssid + "'")
 
-	adaptor.SetWifiMode(espat.WifiModeClient)
-	adaptor.ConnectToAP(ssid, pass, 10)
+	if err := adaptor.ConnectToAccessPoint(ssid, pass, 10*time.Second); err != nil {
+		failMessage(err.Error())
+	}
 
 	println("Connected.")
 	ip, err := adaptor.GetClientIP()

examples/espat/mqttsub/main.go

@@ -129,8 +129,9 @@ func connectToESP() bool {
 func connectToAP() {
 	println("Connecting to wifi network '" + ssid + "'")
 
-	adaptor.SetWifiMode(espat.WifiModeClient)
-	adaptor.ConnectToAP(ssid, pass, 10)
+	if err := adaptor.ConnectToAccessPoint(ssid, pass, 10*time.Second); err != nil {
+		failMessage(err.Error())
+	}
 
 	println("Connected.")
 	ip, err := adaptor.GetClientIP()

examples/espat/tcpclient/main.go

@@ -91,8 +91,9 @@ func connectToESP() bool {
 func connectToAP() {
 	println("Connecting to wifi network '" + ssid + "'")
 
-	adaptor.SetWifiMode(espat.WifiModeClient)
-	adaptor.ConnectToAP(ssid, pass, 10)
+	if err := adaptor.ConnectToAccessPoint(ssid, pass, 10*time.Second); err != nil {
+		failMessage(err.Error())
+	}
 
 	println("Connected.")
 	ip, err := adaptor.GetClientIP()

examples/ft6336/basic/m5stack_core2.go

@@ -0,0 +1,24 @@
+//go:build m5stack_core2
+// +build m5stack_core2
+
+package main
+
+import (
+	"machine"
+
+	"tinygo.org/x/drivers/ft6336"
+	"tinygo.org/x/drivers/i2csoft"
+	"tinygo.org/x/drivers/touch"
+)
+
+// InitDisplay initializes the display of each board.
+func initDevices() (touch.Pointer, error) {
+	i2c := i2csoft.New(machine.SCL0_PIN, machine.SDA0_PIN)
+	i2c.Configure(i2csoft.I2CConfig{Frequency: 100e3})
+
+	resistiveTouch := ft6336.New(i2c, machine.Pin(39))
+	resistiveTouch.Configure(ft6336.Config{})
+	resistiveTouch.SetPeriodActive(0x00)
+
+	return resistiveTouch, nil
+}

examples/ft6336/basic/main.go

@@ -0,0 +1,16 @@
+package main
+
+func main() {
+	touchScreen, _ := initDevices()
+
+	for {
+		touch := touchScreen.ReadTouchPoint()
+		if touch.Z > 0 {
+			//X and Y are 16 bit with 12 bit resolution and need to be scaled for the display size
+			//Z is 24 bit and is typically > 2000 for a touch
+			println("touch:", touch.X, touch.Y, touch.Z)
+			//Example of scaling for m5stack-core2's 320x240 display with 320x270 touch area
+			println("screen:", (touch.X*320)>>16, (touch.Y*270)>>16)
+		}
+	}
+}

examples/ft6336/touchpaint/m5stack_core2.go

@@ -0,0 +1,55 @@
+//go:build m5stack_core2
+// +build m5stack_core2
+
+package main
+
+import (
+	"image/color"
+	"machine"
+
+	axp192 "tinygo.org/x/drivers/axp192/m5stack-core2-axp192"
+	"tinygo.org/x/drivers/ft6336"
+	"tinygo.org/x/drivers/i2csoft"
+	"tinygo.org/x/drivers/ili9341"
+	"tinygo.org/x/drivers/touch"
+)
+
+// InitDisplay initializes the display of each board.
+func initDevices() (touchPaintDisplay, touch.Pointer, error) {
+	machine.SPI2.Configure(machine.SPIConfig{
+		SCK:       machine.LCD_SCK_PIN,
+		SDO:       machine.LCD_SDO_PIN,
+		SDI:       machine.LCD_SDI_PIN,
+		Frequency: 40e6,
+	})
+
+	i2c := i2csoft.New(machine.SCL0_PIN, machine.SDA0_PIN)
+	i2c.Configure(i2csoft.I2CConfig{Frequency: 100e3})
+
+	axp := axp192.New(i2c)
+	led := axp.LED
+	led.Low()
+
+	display := ili9341.NewSPI(
+		machine.SPI2,
+		machine.LCD_DC_PIN,
+		machine.LCD_SS_PIN,
+		machine.NoPin,
+	)
+
+	// configure display
+	display.Configure(ili9341.Config{
+		Width:            320,
+		Height:           240,
+		DisplayInversion: true,
+	})
+	display.FillScreen(color.RGBA{255, 255, 255, 255})
+
+	display.SetRotation(ili9341.Rotation0Mirror)
+
+	resistiveTouch := ft6336.New(i2c, machine.Pin(39))
+	resistiveTouch.Configure(ft6336.Config{})
+	resistiveTouch.SetPeriodActive(0x00)
+
+	return display, resistiveTouch, nil
+}

examples/ft6336/touchpaint/main.go

@@ -0,0 +1,163 @@
+package main
+
+import (
+	"image/color"
+	"math"
+
+	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/touch"
+)
+
+type touchPaintDisplay interface {
+	drivers.Displayer
+	FillRectangle(x, y, width, height int16, c color.RGBA) error
+	DrawRectangle(x, y, w, h int16, c color.RGBA) error
+}
+
+var (
+	white   = color.RGBA{255, 255, 255, 255}
+	black   = color.RGBA{0, 0, 0, 255}
+	red     = color.RGBA{255, 0, 0, 255}
+	green   = color.RGBA{0, 255, 0, 255}
+	blue    = color.RGBA{0, 0, 255, 255}
+	magenta = color.RGBA{255, 0, 255, 255}
+	yellow  = color.RGBA{255, 255, 0, 255}
+	cyan    = color.RGBA{0, 255, 255, 255}
+
+	oldColor     color.RGBA
+	currentColor color.RGBA
+)
+
+const (
+	penRadius = 3
+	boxSize   = 30
+
+	Xmin = 0
+	Xmax = 0xFFFF
+	Ymin = 0
+	Ymax = 0xFFFF
+)
+
+func main() {
+	display, resistiveTouch, _ := initDevices()
+
+	// fill the background and activate the backlight
+	width, height := display.Size()
+	display.FillRectangle(0, 0, width, height, black)
+
+	// make color selection boxes
+	display.FillRectangle(0, 0, boxSize, boxSize, red)
+	display.FillRectangle(boxSize, 0, boxSize, boxSize, yellow)
+	display.FillRectangle(boxSize*2, 0, boxSize, boxSize, green)
+	display.FillRectangle(boxSize*3, 0, boxSize, boxSize, cyan)
+	display.FillRectangle(boxSize*4, 0, boxSize, boxSize, blue)
+	display.FillRectangle(boxSize*5, 0, boxSize, boxSize, magenta)
+	display.FillRectangle(boxSize*6, 0, boxSize, boxSize, black)
+	display.FillRectangle(boxSize*7, 0, boxSize, boxSize, white)
+
+	// set the initial color to red and draw a box to highlight it
+	oldColor = red
+	currentColor = red
+	display.DrawRectangle(0, 0, boxSize, boxSize, white)
+
+	last := touch.Point{}
+
+	// loop and poll for touches, including performing debouncing
+	debounce := 0
+	for {
+
+		point := resistiveTouch.ReadTouchPoint()
+		touch := touch.Point{}
+		if point.Z>>6 > 100 {
+			rawX := mapval(point.X, Xmin, Xmax, 0, int(width))
+			rawY := mapval(point.Y, Ymin, Ymax, 0, int(height))
+			touch.X = rawX
+			touch.Y = rawY
+			touch.Z = 1
+		} else {
+			touch.X = 0
+			touch.Y = 0
+			touch.Z = 0
+		}
+
+		if last.Z != touch.Z {
+			debounce = 0
+			last = touch
+		} else if math.Abs(float64(touch.X-last.X)) > 4 ||
+			math.Abs(float64(touch.Y-last.Y)) > 4 {
+			debounce = 0
+			last = touch
+		} else if debounce > 1 {
+			debounce = 0
+			HandleTouch(display, last)
+		} else if touch.Z > 0 {
+			debounce++
+		} else {
+			last = touch
+			debounce = 0
+		}
+
+	}
+}
+
+// based on Arduino's "map" function
+func mapval(x int, inMin int, inMax int, outMin int, outMax int) int {
+	return (x-inMin)*(outMax-outMin)/(inMax-inMin) + outMin
+}
+
+func HandleTouch(display touchPaintDisplay, touch touch.Point) {
+
+	if int16(touch.Y) < boxSize {
+		oldColor = currentColor
+		x := int16(touch.X)
+		switch {
+		case x < boxSize:
+			currentColor = red
+		case x < boxSize*2:
+			currentColor = yellow
+		case x < boxSize*3:
+			currentColor = green
+		case x < boxSize*4:
+			currentColor = cyan
+		case x < boxSize*5:
+			currentColor = blue
+		case x < boxSize*6:
+			currentColor = magenta
+		case x < boxSize*7:
+			currentColor = black
+		case x < boxSize*8:
+			currentColor = white
+		}
+
+		if oldColor == currentColor {
+			return
+		}
+
+		display.DrawRectangle((x/boxSize)*boxSize, 0, boxSize, boxSize, white)
+		switch oldColor {
+		case red:
+			x = 0
+		case yellow:
+			x = boxSize
+		case green:
+			x = boxSize * 2
+		case cyan:
+			x = boxSize * 3
+		case blue:
+			x = boxSize * 4
+		case magenta:
+			x = boxSize * 5
+		case black:
+			x = boxSize * 6
+		case white:
+			x = boxSize * 7
+		}
+		display.FillRectangle(int16(x), 0, boxSize, boxSize, oldColor)
+
+	}
+
+	if (int16(touch.Y) - penRadius) > boxSize {
+		display.FillRectangle(
+			int16(touch.X), int16(touch.Y), penRadius*2, penRadius*2, currentColor)
+	}
+}

examples/hts221/main.go

@@ -0,0 +1,35 @@
+package main
+
+import (
+	"machine"
+	"time"
+
+	"tinygo.org/x/drivers/hts221"
+)
+
+func main() {
+
+	// use Nano 33 BLE Sense's internal I2C bus
+	machine.I2C1.Configure(machine.I2CConfig{
+		SCL:       machine.SCL1_PIN,
+		SDA:       machine.SDA1_PIN,
+		Frequency: machine.TWI_FREQ_400KHZ,
+	})
+
+	sensor := hts221.New(machine.I2C1)
+
+	sensor.Configure() // power on and calibrate
+
+	if !sensor.Connected() {
+		println("HTS221 not connected!")
+		return
+	}
+
+	for {
+		h, _ := sensor.ReadHumidity()
+		t, _ := sensor.ReadTemperature()
+		println("h =", float32(h)/100.0, "% / t =", float32(t)/1000.0, "*C")
+		time.Sleep(time.Second)
+	}
+
+}

examples/i2csoft/adt7410/main.go

@@ -0,0 +1,27 @@
+package main
+
+import (
+	"fmt"
+	"machine"
+	"time"
+
+	"tinygo.org/x/drivers/adt7410"
+	"tinygo.org/x/drivers/i2csoft"
+)
+
+func main() {
+	i2c := i2csoft.New(machine.SCL_PIN, machine.SDA_PIN)
+	i2c.Configure(i2csoft.I2CConfig{
+		Frequency: 400e3,
+	})
+
+	sensor := adt7410.New(i2c)
+	sensor.Configure()
+
+	for {
+		temp := sensor.ReadTempF()
+		fmt.Printf("temperature: %f\r\n", temp)
+		time.Sleep(time.Second)
+	}
+
+}

examples/ili9341/basic/atsamd21.go

@@ -1,29 +0,0 @@
-// +build atsamd21
-
-package main
-
-import (
-	"machine"
-
-	"tinygo.org/x/drivers/ili9341"
-)
-
-var (
-	display = ili9341.NewSPI(
-		machine.SPI0,
-		machine.D0,
-		machine.D1,
-		machine.D2,
-	)
-
-	backlight = machine.D3
-)
-
-func init() {
-	machine.SPI0.Configure(machine.SPIConfig{
-		SCK:       machine.SPI0_SCK_PIN,
-		SDO:       machine.SPI0_SDO_PIN,
-		SDI:       machine.SPI0_SDI_PIN,
-		Frequency: 24000000,
-	})
-}

examples/ili9341/basic/main.go

@@ -2,9 +2,9 @@ package main
 
 import (
 	"image/color"
-	"machine"
 	"time"
 
+	"tinygo.org/x/drivers/examples/ili9341/initdisplay"
 	"tinygo.org/x/drivers/ili9341"
 )
 
@@ -16,16 +16,15 @@ var (
 	green = color.RGBA{0, 255, 0, 255}
 )
 
+var (
+	display *ili9341.Device
+)
+
 func main() {
+	display = initdisplay.InitDisplay()
 
-	backlight.Configure(machine.PinConfig{machine.PinOutput})
-
-	display.Configure(ili9341.Config{})
 	width, height := display.Size()
 
-	display.FillScreen(black)
-	backlight.High()
-
 	display.FillRectangle(0, 0, width/2, height/2, white)
 	display.FillRectangle(width/2, 0, width/2, height/2, red)
 	display.FillRectangle(0, height/2, width/2, height/2, green)

examples/ili9341/basic/pyportal.go

@@ -1,22 +0,0 @@
-// +build pyportal
-
-package main
-
-import (
-	"machine"
-
-	"tinygo.org/x/drivers/ili9341"
-)
-
-var (
-	display = ili9341.NewParallel(
-		machine.LCD_DATA0,
-		machine.TFT_WR,
-		machine.TFT_DC,
-		machine.TFT_CS,
-		machine.TFT_RESET,
-		machine.TFT_RD,
-	)
-
-	backlight = machine.TFT_BACKLIGHT
-)

examples/ili9341/basic/wioterminal.go

@@ -1,29 +0,0 @@
-// +build wioterminal
-
-package main
-
-import (
-	"machine"
-
-	"tinygo.org/x/drivers/ili9341"
-)
-
-var (
-	display = ili9341.NewSPI(
-		machine.SPI3,
-		machine.LCD_DC,
-		machine.LCD_SS_PIN,
-		machine.LCD_RESET,
-	)
-
-	backlight = machine.LCD_BACKLIGHT
-)
-
-func init() {
-	machine.SPI3.Configure(machine.SPIConfig{
-		SCK:       machine.LCD_SCK_PIN,
-		SDO:       machine.LCD_SDO_PIN,
-		SDI:       machine.LCD_SDI_PIN,
-		Frequency: 40000000,
-	})
-}

examples/ili9341/initdisplay/atsamd21.go

@@ -0,0 +1,41 @@
+//go:build atsamd21
+// +build atsamd21
+
+package initdisplay
+
+import (
+	"machine"
+
+	"tinygo.org/x/drivers/ili9341"
+)
+
+var ()
+
+func InitDisplay() *ili9341.Device {
+	machine.SPI0.Configure(machine.SPIConfig{
+		SCK:       machine.SPI0_SCK_PIN,
+		SDO:       machine.SPI0_SDO_PIN,
+		SDI:       machine.SPI0_SDI_PIN,
+		Frequency: 24000000,
+	})
+
+	// configure backlight
+	backlight := machine.D3
+	backlight.Configure(machine.PinConfig{machine.PinOutput})
+
+	display := ili9341.NewSPI(
+		machine.SPI0,
+		machine.D0,
+		machine.D1,
+		machine.D2,
+	)
+
+	// configure display
+	display.Configure(ili9341.Config{})
+
+	backlight.High()
+
+	display.SetRotation(ili9341.Rotation270)
+
+	return display
+}

examples/ili9341/initdisplay/m5stack.go

@@ -0,0 +1,43 @@
+//go:build m5stack
+// +build m5stack
+
+package initdisplay
+
+import (
+	"machine"
+
+	"tinygo.org/x/drivers/ili9341"
+)
+
+func InitDisplay() *ili9341.Device {
+	machine.SPI2.Configure(machine.SPIConfig{
+		SCK:       machine.SPI0_SCK_PIN,
+		SDO:       machine.SPI0_SDO_PIN,
+		SDI:       machine.SPI0_SDI_PIN,
+		Frequency: 40e6,
+	})
+
+	// configure backlight
+	backlight := machine.LCD_BL_PIN
+	backlight.Configure(machine.PinConfig{machine.PinOutput})
+
+	display := ili9341.NewSPI(
+		machine.SPI2,
+		machine.LCD_DC_PIN,
+		machine.LCD_SS_PIN,
+		machine.LCD_RST_PIN,
+	)
+
+	// configure display
+	display.Configure(ili9341.Config{
+		Width:            320,
+		Height:           240,
+		DisplayInversion: true,
+	})
+
+	backlight.High()
+
+	display.SetRotation(ili9341.Rotation0Mirror)
+
+	return display
+}

examples/ili9341/initdisplay/m5stack_core2.go

@@ -0,0 +1,49 @@
+//go:build m5stack_core2
+// +build m5stack_core2
+
+package initdisplay
+
+import (
+	"image/color"
+	"machine"
+
+	axp192 "tinygo.org/x/drivers/axp192/m5stack-core2-axp192"
+	"tinygo.org/x/drivers/i2csoft"
+	"tinygo.org/x/drivers/ili9341"
+)
+
+// InitDisplay initializes the display of each board.
+func InitDisplay() *ili9341.Device {
+	machine.SPI2.Configure(machine.SPIConfig{
+		SCK:       machine.LCD_SCK_PIN,
+		SDO:       machine.LCD_SDO_PIN,
+		SDI:       machine.LCD_SDI_PIN,
+		Frequency: 40e6,
+	})
+
+	i2c := i2csoft.New(machine.SCL0_PIN, machine.SDA0_PIN)
+	i2c.Configure(i2csoft.I2CConfig{Frequency: 100e3})
+
+	axp := axp192.New(i2c)
+	led := axp.LED
+	led.Low()
+
+	display := ili9341.NewSPI(
+		machine.SPI2,
+		machine.LCD_DC_PIN,
+		machine.LCD_SS_PIN,
+		machine.NoPin,
+	)
+
+	// configure display
+	display.Configure(ili9341.Config{
+		Width:            320,
+		Height:           240,
+		DisplayInversion: true,
+	})
+	display.FillScreen(color.RGBA{255, 255, 255, 255})
+
+	display.SetRotation(ili9341.Rotation0Mirror)
+
+	return display
+}

examples/ili9341/initdisplay/pyportal.go

@@ -0,0 +1,34 @@
+//go:build pyportal
+// +build pyportal
+
+package initdisplay
+
+import (
+	"machine"
+
+	"tinygo.org/x/drivers/ili9341"
+)
+
+func InitDisplay() *ili9341.Device {
+	display := ili9341.NewParallel(
+		machine.LCD_DATA0,
+		machine.TFT_WR,
+		machine.TFT_DC,
+		machine.TFT_CS,
+		machine.TFT_RESET,
+		machine.TFT_RD,
+	)
+
+	// configure backlight
+	backlight := machine.TFT_BACKLIGHT
+	backlight.Configure(machine.PinConfig{machine.PinOutput})
+
+	// configure display
+	display.Configure(ili9341.Config{})
+
+	backlight.High()
+
+	display.SetRotation(ili9341.Rotation270)
+
+	return display
+}

examples/ili9341/initdisplay/wioterminal.go

@@ -0,0 +1,39 @@
+//go:build wioterminal
+// +build wioterminal
+
+package initdisplay
+
+import (
+	"machine"
+
+	"tinygo.org/x/drivers/ili9341"
+)
+
+func InitDisplay() *ili9341.Device {
+	machine.SPI3.Configure(machine.SPIConfig{
+		SCK:       machine.LCD_SCK_PIN,
+		SDO:       machine.LCD_SDO_PIN,
+		SDI:       machine.LCD_SDI_PIN,
+		Frequency: 40000000,
+	})
+
+	// configure backlight
+	backlight := machine.LCD_BACKLIGHT
+	backlight.Configure(machine.PinConfig{machine.PinOutput})
+
+	display := ili9341.NewSPI(
+		machine.SPI3,
+		machine.LCD_DC,
+		machine.LCD_SS_PIN,
+		machine.LCD_RESET,
+	)
+
+	// configure display
+	display.Configure(ili9341.Config{})
+
+	backlight.High()
+
+	display.SetRotation(ili9341.Rotation270)
+
+	return display
+}

examples/ili9341/pyportal_boing/main.go

@@ -3,9 +3,9 @@
 package main
 
 import (
-	"machine"
 	"time"
 
+	"tinygo.org/x/drivers/examples/ili9341/initdisplay"
 	"tinygo.org/x/drivers/examples/ili9341/pyportal_boing/graphics"
 	"tinygo.org/x/drivers/ili9341"
 )
@@ -25,7 +25,7 @@ const (
 )
 
 var (
-	frameBuffer = [(graphics.BALLHEIGHT + 8) * (graphics.BALLWIDTH + 8)]uint16{}
+	frameBuffer = [(graphics.BALLHEIGHT + 8) * (graphics.BALLWIDTH + 8) * 2]uint8{}
 
 	startTime int64
 	frame     int64
@@ -44,20 +44,17 @@ var (
 	palette [16]uint16
 )
 
+var (
+	display *ili9341.Device
+)
+
 func main() {
+	display = initdisplay.InitDisplay()
 
-	// configure backlight
-	backlight.Configure(machine.PinConfig{machine.PinOutput})
-
-	// configure display
-	display.Configure(ili9341.Config{})
 	print("width, height == ")
 	width, height := display.Size()
 	println(width, height)
 
-	backlight.High()
-
-	display.SetRotation(ili9341.Rotation270)
 	DrawBackground()
 
 	startTime = time.Now().UnixNano()
@@ -179,7 +176,8 @@ func main() {
 						c = BGCOLOR
 					}
 				}
-				frameBuffer[y*int(width)+x] = c
+				frameBuffer[(y*int(width)+x)*2] = byte(c >> 8)
+				frameBuffer[(y*int(width)+x)*2+1] = byte(c)
 				bx1++ // Increment bitmap position counters (X axis)
 				bgx1++
 			}
@@ -190,7 +188,7 @@ func main() {
 			bgy++
 		}
 
-		display.DrawRGBBitmap(minx, miny, frameBuffer[:width*height], width, height)
+		display.DrawRGBBitmap8(minx, miny, frameBuffer[:width*height*2], width, height)
 
 		// Show approximate frame rate
 		frame++
@@ -215,11 +213,13 @@ func DrawBackground() {
 				b = graphics.Background[j*byteWidth+k/8]
 			}
 			if b&0x80 == 0 {
-				frameBuffer[k] = BGCOLOR
+				frameBuffer[2*k] = byte(BGCOLOR >> 8)
+				frameBuffer[2*k+1] = byte(BGCOLOR & 0xFF)
 			} else {
-				frameBuffer[k] = GRIDCOLOR
+				frameBuffer[2*k] = byte(GRIDCOLOR >> 8)
+				frameBuffer[2*k+1] = byte(GRIDCOLOR & 0xFF)
 			}
 		}
-		display.DrawRGBBitmap(0, j, frameBuffer[0:w], w, 1)
+		display.DrawRGBBitmap8(0, j, frameBuffer[0:w*2], w, 1)
 	}
 }

examples/ili9341/pyportal_boing/pyportal.go

@@ -1,22 +0,0 @@
-// +build pyportal
-
-package main
-
-import (
-	"machine"
-
-	"tinygo.org/x/drivers/ili9341"
-)
-
-var (
-	display = ili9341.NewParallel(
-		machine.LCD_DATA0,
-		machine.TFT_WR,
-		machine.TFT_DC,
-		machine.TFT_CS,
-		machine.TFT_RESET,
-		machine.TFT_RD,
-	)
-
-	backlight = machine.TFT_BACKLIGHT
-)

examples/ili9341/pyportal_boing/wioterminal.go

@@ -1,29 +0,0 @@
-// +build wioterminal
-
-package main
-
-import (
-	"machine"
-
-	"tinygo.org/x/drivers/ili9341"
-)
-
-var (
-	display = ili9341.NewSPI(
-		machine.SPI3,
-		machine.LCD_DC,
-		machine.LCD_SS_PIN,
-		machine.LCD_RESET,
-	)
-
-	backlight = machine.LCD_BACKLIGHT
-)
-
-func init() {
-	machine.SPI3.Configure(machine.SPIConfig{
-		SCK:       machine.LCD_SCK_PIN,
-		SDO:       machine.LCD_SDO_PIN,
-		SDI:       machine.LCD_SDI_PIN,
-		Frequency: 40000000,
-	})
-}

examples/ili9341/scroll/atsamd21.go

@@ -1,29 +0,0 @@
-// +build atsamd21
-
-package main
-
-import (
-	"machine"
-
-	"tinygo.org/x/drivers/ili9341"
-)
-
-var (
-	display = ili9341.NewSPI(
-		machine.SPI0,
-		machine.D0,
-		machine.D1,
-		machine.D2,
-	)
-
-	backlight = machine.D3
-)
-
-func init() {
-	machine.SPI0.Configure(machine.SPIConfig{
-		SCK:       machine.SPI0_SCK_PIN,
-		SDO:       machine.SPI0_SDO_PIN,
-		SDI:       machine.SPI0_SDI_PIN,
-		Frequency: 24000000,
-	})
-}

examples/ili9341/scroll/main.go

@@ -2,9 +2,9 @@ package main
 
 import (
 	"image/color"
-	"machine"
 	"time"
 
+	"tinygo.org/x/drivers/examples/ili9341/initdisplay"
 	"tinygo.org/x/drivers/ili9341"
 )
 
@@ -16,16 +16,15 @@ var (
 	white = color.RGBA{255, 255, 255, 255}
 )
 
+var (
+	display *ili9341.Device
+)
+
 func main() {
+	display := initdisplay.InitDisplay()
 
-	backlight.Configure(machine.PinConfig{machine.PinOutput})
-
-	display.Configure(ili9341.Config{})
 	width, height := display.Size()
 
-	display.FillScreen(black)
-	backlight.High()
-
 	display.FillRectangle(0, 0, width/2, height/2, white)
 	display.FillRectangle(width/2, 0, width/2, height/2, red)
 	display.FillRectangle(0, height/2, width/2, height/2, green)

examples/ili9341/scroll/pyportal.go

@@ -1,22 +0,0 @@
-// +build pyportal
-
-package main
-
-import (
-	"machine"
-
-	"tinygo.org/x/drivers/ili9341"
-)
-
-var (
-	display = ili9341.NewParallel(
-		machine.LCD_DATA0,
-		machine.TFT_WR,
-		machine.TFT_DC,
-		machine.TFT_CS,
-		machine.TFT_RESET,
-		machine.TFT_RD,
-	)
-
-	backlight = machine.TFT_BACKLIGHT
-)

examples/ili9341/scroll/wioterminal.go

@@ -1,29 +0,0 @@
-// +build wioterminal
-
-package main
-
-import (
-	"machine"
-
-	"tinygo.org/x/drivers/ili9341"
-)
-
-var (
-	display = ili9341.NewSPI(
-		machine.SPI3,
-		machine.LCD_DC,
-		machine.LCD_SS_PIN,
-		machine.LCD_RESET,
-	)
-
-	backlight = machine.LCD_BACKLIGHT
-)
-
-func init() {
-	machine.SPI3.Configure(machine.SPIConfig{
-		SCK:       machine.LCD_SCK_PIN,
-		SDO:       machine.LCD_SDO_PIN,
-		SDI:       machine.LCD_SDI_PIN,
-		Frequency: 40000000,
-	})
-}

examples/ili9341/slideshow/README.md

@@ -0,0 +1,18 @@
+# examples/ili9341/slideshow
+
+![](./slideshow.jpg)
+
+This example uses the image package for TinyGo to display png and jpeg images.  
+
+## How to create an image
+
+The following program will output an image binary like the one in [images.go](./images.go).  
+
+```
+go run ./examples/ili9341/slideshow/convert2bin ./path/to/png_or_jpg.png
+```
+
+## Notes
+
+Displaying a 320x240 png or jpeg often requires more than 50KB of memory.  
+The examples include samd21 settings, but if you run them as is, you will get a memory size error.  

examples/ili9341/slideshow/main.go

@@ -0,0 +1,95 @@
+package main
+
+import (
+	"fmt"
+	"image/color"
+	"strings"
+	"time"
+
+	"tinygo.org/x/drivers/examples/ili9341/initdisplay"
+	"tinygo.org/x/drivers/ili9341"
+	"tinygo.org/x/drivers/image/jpeg"
+	"tinygo.org/x/drivers/image/png"
+)
+
+var (
+	black = color.RGBA{0, 0, 0, 255}
+	white = color.RGBA{255, 255, 255, 255}
+	red   = color.RGBA{255, 0, 0, 255}
+	blue  = color.RGBA{0, 0, 255, 255}
+	green = color.RGBA{0, 255, 0, 255}
+)
+
+var (
+	display *ili9341.Device
+)
+
+func main() {
+	err := run()
+	for err != nil {
+		errorMessage(err)
+	}
+}
+
+func run() error {
+	display = initdisplay.InitDisplay()
+
+	width, height := display.Size()
+	if width < 320 || height < 240 {
+		display.SetRotation(ili9341.Rotation270)
+	}
+
+	display.FillScreen(black)
+
+	for {
+		err := drawJpeg(display)
+		if err != nil {
+			return err
+		}
+		time.Sleep(time.Second)
+
+		err = drawPng(display)
+		if err != nil {
+			return err
+		}
+		time.Sleep(time.Second)
+	}
+
+	return nil
+}
+
+// Define the buffer required for the callback. In most cases, this setting
+// should be sufficient.  For jpeg, the callback will always be called every
+// 3*8*8*4 pix. png will be called every line, i.e. every width pix.
+var buffer [3 * 8 * 8 * 4]uint16
+
+func drawPng(display *ili9341.Device) error {
+	p := strings.NewReader(pngImage)
+	png.SetCallback(buffer[:], func(data []uint16, x, y, w, h, width, height int16) {
+		err := display.DrawRGBBitmap(x, y, data[:w*h], w, h)
+		if err != nil {
+			errorMessage(fmt.Errorf("error drawPng: %s", err))
+		}
+	})
+
+	return png.Decode(p)
+}
+
+func drawJpeg(display *ili9341.Device) error {
+	p := strings.NewReader(jpegImage)
+	jpeg.SetCallback(buffer[:], func(data []uint16, x, y, w, h, width, height int16) {
+		err := display.DrawRGBBitmap(x, y, data[:w*h], w, h)
+		if err != nil {
+			errorMessage(fmt.Errorf("error drawJpeg: %s", err))
+		}
+	})
+
+	return jpeg.Decode(p)
+}
+
+func errorMessage(err error) {
+	for {
+		fmt.Printf("%s\r\n", err.Error())
+		time.Sleep(5 * time.Second)
+	}
+}

examples/lps22hb/main.go

@@ -0,0 +1,35 @@
+package main
+
+import (
+	"machine"
+	"time"
+
+	"tinygo.org/x/drivers/lps22hb"
+)
+
+func main() {
+
+	// use Nano 33 BLE Sense's internal I2C bus
+	machine.I2C1.Configure(machine.I2CConfig{
+		SCL:       machine.SCL1_PIN,
+		SDA:       machine.SDA1_PIN,
+		Frequency: machine.TWI_FREQ_400KHZ,
+	})
+
+	sensor := lps22hb.New(machine.I2C1)
+	sensor.Configure()
+
+	if !sensor.Connected() {
+		println("LPS22HB not connected!")
+		return
+	}
+
+	for {
+		p, _ := sensor.ReadPressure()
+		t, _ := sensor.ReadTemperature()
+		println("p =", float32(p)/1000.0, "hPa / t =", float32(t)/1000.0, "*C")
+		time.Sleep(time.Second)
+		// note: the device would power down itself after each query
+	}
+
+}

examples/lsm303agr/main.go

@@ -3,37 +3,54 @@ package main
 import (
 	"machine"
 	"time"
+
 	"tinygo.org/x/drivers/lsm303agr"
 )
 
 func main() {
 
+	// LSM303AGR/MAG is connected to the I2C0 bus on micro:bit v1 (the same as P19/P20) and v2 (internal)
 	machine.I2C0.Configure(machine.I2CConfig{})
-	accel_mag := lsm303agr.New(machine.I2C0)
 
-	if !accel_mag.Connected() {
+	sensor := lsm303agr.New(machine.I2C0)
+	sensor.Configure(lsm303agr.Configuration{}) //default settings
+
+	// you can specify the following options to adjust accuracy, sensor range or save power.
+	// see https://github.com/tinygo-org/drivers/blob/release/lsm303agr/registers.go for details:
+	/*
+		sensor.Configure(lsm303agr.Configuration{
+			AccelPowerMode: lsm303agr.ACCEL_POWER_NORMAL,
+			AccelRange:     lsm303agr.ACCEL_RANGE_2G,
+			AccelDataRate:  lsm303agr.ACCEL_DATARATE_100HZ,
+			MagPowerMode:   lsm303agr.MAG_POWER_NORMAL,
+			MagSystemMode:  lsm303agr.MAG_SYSTEM_CONTINUOUS,
+			MagDataRate:    lsm303agr.MAG_DATARATE_10HZ,
+		})
+	*/
+
+	if !sensor.Connected() {
 		println("LSM303AGR/MAG not connected!")
 		return
 	}
 
-	accel_mag.Configure(lsm303agr.Configuration{}) //default settings
-
 	for {
+		// accel_x, accel_y, accel_z := sensor.ReadAcceleration()
+		// println("ACCEL_X:", accel_x/100000, " ACCEL_Y:", accel_y/100000, " ACCEL_Z:", accel_z/100000)
 
-		accel_x, accel_y, accel_z := accel_mag.ReadAcceleration()
-		pitch, roll := accel_mag.ReadPitchRoll()
-		mag_x, mag_y, mag_z := accel_mag.ReadMagneticField()
-		heading := accel_mag.ReadCompass()
-		temp, _ := accel_mag.ReadTemperature()
+		// mag_x, mag_y, mag_z := sensor.ReadMagneticField()
+		// println("MAG_X:", mag_x/100000, " MAG_Y:", mag_y/100000, " MAG_Z:", mag_z/100000)
+
+		pitch, roll := sensor.ReadPitchRoll()
+		println("Pitch:", float32(pitch)/100000, " Roll:", float32(roll)/100000)
+
+		heading := sensor.ReadCompass()
+		println("Heading:", float32(heading)/100000, "degrees")
+
+		temp, _ := sensor.ReadTemperature()
+		println("Temperature:", float32(temp)/1000, "*C")
 
-		println("ACCEL_X:", accel_x, " ACCEL_Y:", accel_y, " ACCEL_Z:", accel_z)
-		println("MAG_X:", mag_x, " MAG_Y:", mag_y, " MAG_Z:", mag_z)
-		println("Pitch:", pitch, " Roll:", roll)
-		println("Heading:", heading)
-		println("Temperature:", temp/1000)
 		println("\n")
-
-		time.Sleep(time.Millisecond * 100)
+		time.Sleep(time.Millisecond * 250)
 	}
 
 }

examples/lsm6dsox/main.go

@@ -0,0 +1,108 @@
+// Connects to an LSM6DSOX I2C a 6 axis Inertial Measurement Unit (IMU)
+package main
+
+import (
+	"fmt"
+	"machine"
+	"time"
+
+	"tinygo.org/x/drivers/lsm6dsox"
+)
+
+const (
+	PLOTTER           = true
+	SHOW_ACCELERATION = false
+	SHOW_ROTATION     = true
+	SHOW_TEMPERATURE  = false
+
+	// calibration is naive, good enough for a demo: do not shake a second after flashing
+	GYRO_CALIBRATION = true
+)
+
+var cal = [...]float32{0, 0, 0}
+
+func main() {
+
+	machine.I2C0.Configure(machine.I2CConfig{})
+
+	device := lsm6dsox.New(machine.I2C0)
+	device.Configure(lsm6dsox.Configuration{
+		AccelRange:      lsm6dsox.ACCEL_2G,
+		AccelSampleRate: lsm6dsox.ACCEL_SR_104,
+		GyroRange:       lsm6dsox.GYRO_250DPS,
+		GyroSampleRate:  lsm6dsox.GYRO_SR_104,
+	})
+
+	for {
+
+		if !device.Connected() {
+			println("LSM6DSOX not connected")
+			time.Sleep(time.Second)
+			continue
+		}
+
+		// heuristic: after successful calibration the value can't be 0
+		if GYRO_CALIBRATION && cal[0] == 0 {
+			calibrateGyro(device)
+		}
+
+		ax, ay, az := device.ReadAcceleration()
+		gx, gy, gz := device.ReadRotation()
+		t, _ := device.ReadTemperature()
+
+		if PLOTTER {
+			printPlotter(ax, ay, az, gx, gy, gz, t)
+			time.Sleep(time.Millisecond * 100)
+		} else {
+			printMonitor(ax, ay, az, gx, gy, gz, t)
+			time.Sleep(time.Millisecond * 1000)
+		}
+
+	}
+
+}
+
+func calibrateGyro(device *lsm6dsox.Device) {
+	for i := 0; i < 100; i++ {
+		gx, gy, gz := device.ReadRotation()
+		cal[0] += float32(gx) / 1000000
+		cal[1] += float32(gy) / 1000000
+		cal[2] += float32(gz) / 1000000
+		time.Sleep(time.Millisecond * 10)
+	}
+	cal[0] /= 100
+	cal[1] /= 100
+	cal[2] /= 100
+}
+
+// Arduino IDE's Serial Plotter
+func printPlotter(ax, ay, az, gx, gy, gz, t int32) {
+	if SHOW_ACCELERATION {
+		fmt.Printf("AX:%f, AY:%f, AZ:%f,", axis(ax, 0), axis(ay, 0), axis(az, 0))
+	}
+	if SHOW_ROTATION {
+		fmt.Printf("GX:%f, GY:%f, GZ:%f,", axis(gx, cal[0]), axis(gy, cal[1]), axis(gz, cal[2]))
+	}
+	if SHOW_TEMPERATURE {
+		fmt.Printf("T:%f", float32(t)/1000)
+	}
+	println()
+}
+
+// Any Serial Monitor
+func printMonitor(ax, ay, az, gx, gy, gz, t int32) {
+	if SHOW_ACCELERATION {
+		fmt.Printf("Acceleration: %f, %f, %f\r\n", axis(ax, 0), axis(ay, 0), axis(az, 0))
+	}
+	if SHOW_ROTATION {
+		fmt.Printf("Rotation: %f, %f, %f\r\n", axis(gx, cal[0]), axis(gy, cal[1]), axis(gz, cal[2]))
+	}
+	if SHOW_TEMPERATURE {
+		fmt.Printf("Temperature C: %f\r\n", float32(t)/1000)
+	}
+	println()
+}
+
+func axis(raw int32, cal float32) float32 {
+	return float32(raw)/1000000 - cal
+}

examples/lsm9ds1/main.go

@@ -0,0 +1,103 @@
+// LSM9DS1, 9 axis Inertial Measurement Unit (IMU)
+package main
+
+import (
+	"fmt"
+	"machine"
+	"time"
+
+	"tinygo.org/x/drivers/lsm9ds1"
+)
+
+const (
+	PLOTTER             = false
+	SHOW_ACCELERATION   = true
+	SHOW_ROTATION       = true
+	SHOW_MAGNETIC_FIELD = true
+	SHOW_TEMPERATURE    = true
+)
+
+func main() {
+
+	// I2C configure
+	machine.I2C0.Configure(machine.I2CConfig{})
+
+	// LSM9DS1 setup
+	device := lsm9ds1.New(machine.I2C0)
+	err := device.Configure(lsm9ds1.Configuration{
+		AccelRange:      lsm9ds1.ACCEL_2G,
+		AccelSampleRate: lsm9ds1.ACCEL_SR_119,
+		GyroRange:       lsm9ds1.GYRO_250DPS,
+		GyroSampleRate:  lsm9ds1.GYRO_SR_119,
+		MagRange:        lsm9ds1.MAG_4G,
+		MagSampleRate:   lsm9ds1.MAG_SR_40,
+	})
+	if err != nil {
+		for {
+			println("Failed to configure", err.Error())
+			time.Sleep(time.Second)
+		}
+	}
+
+	for {
+
+		if con, err := device.Connected(); !con || err != nil {
+			println("LSM9DS1 not connected")
+			time.Sleep(time.Second)
+			continue
+		}
+
+		ax, ay, az, _ := device.ReadAcceleration()
+		gx, gy, gz, _ := device.ReadRotation()
+		mx, my, mz, _ := device.ReadMagneticField()
+		t, _ := device.ReadTemperature()
+
+		if PLOTTER {
+			printPlotter(ax, ay, az, gx, gy, gz, mx, my, mz, t)
+			time.Sleep(time.Millisecond * 100)
+		} else {
+			printMonitor(ax, ay, az, gx, gy, gz, mx, my, mz, t)
+			time.Sleep(time.Millisecond * 1000)
+		}
+
+	}
+
+}
+
+// Arduino IDE's Serial Plotter
+func printPlotter(ax, ay, az, gx, gy, gz, mx, my, mz, t int32) {
+	if SHOW_ACCELERATION {
+		fmt.Printf("AX:%f, AY:%f, AZ:%f,", axis(ax), axis(ay), axis(az))
+	}
+	if SHOW_ROTATION {
+		fmt.Printf("GX:%f, GY:%f, GZ:%f,", axis(gx), axis(gy), axis(gz))
+	}
+	if SHOW_MAGNETIC_FIELD {
+		fmt.Printf("MX:%d, MY:%d, MZ:%d,", mx, my, mz)
+	}
+	if SHOW_TEMPERATURE {
+		fmt.Printf("T:%f", float32(t)/1000)
+	}
+	println()
+}
+
+// Any Serial Monitor
+func printMonitor(ax, ay, az, gx, gy, gz, mx, my, mz, t int32) {
+	if SHOW_ACCELERATION {
+		fmt.Printf("Acceleration (g): %f, %f, %f\r\n", axis(ax), axis(ay), axis(az))
+	}
+	if SHOW_ROTATION {
+		fmt.Printf("Rotation (dps): %f, %f, %f\r\n", axis(gx), axis(gy), axis(gz))
+	}
+	if SHOW_MAGNETIC_FIELD {
+		fmt.Printf("Magnetic field (nT): %d, %d, %d\r\n", mx, my, mz)
+	}
+	if SHOW_TEMPERATURE {
+		fmt.Printf("Temperature C: %f\r\n", float32(t)/1000)
+	}
+	println()
+}
+
+func axis(raw int32) float32 {
+	return float32(raw) / 1000000
+}

examples/pca9685/main.go

@@ -0,0 +1,68 @@
+package main
+
+import (
+	"machine"
+	"time"
+
+	"tinygo.org/x/drivers/pca9685"
+)
+
+func main() {
+	const (
+		// Default address on most breakout boards.
+		pcaAddr = 0x40
+	)
+	err := machine.I2C0.Configure(machine.I2CConfig{})
+	if err != nil {
+		panic(err.Error())
+	}
+	d := pca9685.New(machine.I2C0, 0x40)
+	err = d.IsConnected()
+	if err != nil {
+		panic(err.Error())
+	}
+	err = d.Configure(pca9685.PWMConfig{Period: 1e9 / 200}) // 200Hz PWM
+	if err != nil {
+		panic(err.Error())
+	}
+
+	var value uint32
+	step := d.Top() / 5
+	for {
+		for value = 0; value <= d.Top(); value += step {
+			d.SetAll(value)
+			dc := 100 * value / d.Top()
+			println("set dc @", dc, "%")
+			time.Sleep(800 * time.Millisecond)
+		}
+	}
+}
+
+// ScanI2CDev finds I2C devices on the bus and rreturns them inside
+// a slice. If slice is nil then no devices were found.
+func ScanI2CDev(bus machine.I2C) (addrs []uint8) {
+	var addr, count uint8
+	var err error
+	w := []byte{1}
+	// Count devices in first scan
+	for addr = 1; addr < 127; addr++ {
+		err = bus.Tx(uint16(addr), w, nil)
+		if err == nil {
+			count++
+		}
+	}
+	if count == 0 {
+		return nil
+	}
+	// Allocate slice and populate slice with addresses
+	addrs = make([]uint8, count)
+	count = 0
+	for addr = 1; addr < 127; addr++ {
+		err = bus.Tx(uint16(addr), w, nil)
+		if err == nil && count < uint8(len(addrs)) {
+			addrs[count] = addr
+			count++
+		}
+	}
+	return addrs
+}

examples/rtl8720dn/mqttclient/main.go

@@ -0,0 +1,131 @@
+// This is a sensor station that uses a RTL8720DN running on the device UART2.
+// It creates an MQTT connection that publishes a message every second
+// to an MQTT broker.
+//
+// In other words:
+// Your computer <--> USB-CDC <--> MCU <--> UART2 <--> RTL8720DN <--> Internet <--> MQTT broker.
+//
+// You must install the Paho MQTT package to build this program:
+//
+// 		go get -u github.com/eclipse/paho.mqtt.golang
+//
+// You can check that mqttpub is running successfully with the following command.
+//
+// 		mosquitto_sub -h test.mosquitto.org -t tinygo
+//
+package main
+
+import (
+	"fmt"
+	"math/rand"
+	"time"
+
+	"tinygo.org/x/drivers/net"
+	"tinygo.org/x/drivers/net/mqtt"
+	"tinygo.org/x/drivers/rtl8720dn"
+)
+
+// You can override the setting with the init() in another source code.
+// func init() {
+//    ssid = "your-ssid"
+//    password = "your-password"
+//    debug = true
+//    server = "tinygo.org"
+// }
+
+var (
+	ssid     string
+	password string
+	server   string = "tcp://test.mosquitto.org:1883"
+	debug           = false
+)
+
+var buf [0x400]byte
+
+var lastRequestTime time.Time
+var conn net.Conn
+var adaptor *rtl8720dn.RTL8720DN
+
+func main() {
+	err := run()
+	for err != nil {
+		fmt.Printf("error: %s\r\n", err.Error())
+		time.Sleep(5 * time.Second)
+	}
+}
+
+var (
+	topic = "tinygo"
+)
+
+func run() error {
+	rtl, err := setupRTL8720DN()
+	if err != nil {
+		return err
+	}
+	net.UseDriver(rtl)
+
+	err = rtl.ConnectToAccessPoint(ssid, password, 10*time.Second)
+	if err != nil {
+		return err
+	}
+
+	ip, subnet, gateway, err := rtl.GetIP()
+	if err != nil {
+		return err
+	}
+	fmt.Printf("IP Address : %s\r\n", ip)
+	fmt.Printf("Mask       : %s\r\n", subnet)
+	fmt.Printf("Gateway    : %s\r\n", gateway)
+
+	rand.Seed(time.Now().UnixNano())
+
+	opts := mqtt.NewClientOptions()
+	opts.AddBroker(server).SetClientID("tinygo-client-" + randomString(10))
+
+	println("Connectng to MQTT...")
+	cl := mqtt.NewClient(opts)
+	if token := cl.Connect(); token.Wait() && token.Error() != nil {
+		failMessage(token.Error().Error())
+	}
+
+	for i := 0; ; i++ {
+		println("Publishing MQTT message...")
+		data := []byte(fmt.Sprintf(`{"e":[{"n":"hello %d","v":101}]}`, i))
+		token := cl.Publish(topic, 0, false, data)
+		token.Wait()
+		if err := token.Error(); err != nil {
+			return err
+		}
+		time.Sleep(100 * time.Millisecond)
+	}
+
+	// Right now this code is never reached. Need a way to trigger it...
+	println("Disconnecting MQTT...")
+	cl.Disconnect(100)
+
+	println("Done.")
+
+	return nil
+}
+
+// Returns an int >= min, < max
+func randomInt(min, max int) int {
+	return min + rand.Intn(max-min)
+}
+
+// Generate a random string of A-Z chars with len = l
+func randomString(len int) string {
+	bytes := make([]byte, len)
+	for i := 0; i < len; i++ {
+		bytes[i] = byte(randomInt(65, 90))
+	}
+	return string(bytes)
+}
+
+func failMessage(msg string) {
+	for {
+		println(msg)
+		time.Sleep(1 * time.Second)
+	}
+}

examples/rtl8720dn/mqttclient/wioterminal.go

@@ -0,0 +1,74 @@
+//go:build wioterminal
+// +build wioterminal
+
+package main
+
+import (
+	"device/sam"
+	"machine"
+	"runtime/interrupt"
+	"time"
+
+	"tinygo.org/x/drivers/rtl8720dn"
+)
+
+var (
+	uart UARTx
+)
+
+func handleInterrupt(interrupt.Interrupt) {
+	// should reset IRQ
+	uart.Receive(byte((uart.Bus.DATA.Get() & 0xFF)))
+	uart.Bus.INTFLAG.SetBits(sam.SERCOM_USART_INT_INTFLAG_RXC)
+}
+
+func setupRTL8720DN() (*rtl8720dn.RTL8720DN, error) {
+	machine.RTL8720D_CHIP_PU.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.RTL8720D_CHIP_PU.Low()
+	time.Sleep(100 * time.Millisecond)
+	machine.RTL8720D_CHIP_PU.High()
+	time.Sleep(1000 * time.Millisecond)
+	if debug {
+		waitSerial()
+	}
+
+	uart = UARTx{
+		UART: &machine.UART{
+			Buffer: machine.NewRingBuffer(),
+			Bus:    sam.SERCOM0_USART_INT,
+			SERCOM: 0,
+		},
+	}
+
+	uart.Interrupt = interrupt.New(sam.IRQ_SERCOM0_2, handleInterrupt)
+	uart.Configure(machine.UARTConfig{TX: machine.PB24, RX: machine.PC24, BaudRate: 614400})
+
+	rtl := rtl8720dn.New(uart)
+	rtl.Debug(debug)
+
+	_, err := rtl.Rpc_tcpip_adapter_init()
+	if err != nil {
+		return nil, err
+	}
+
+	return rtl, nil
+}
+
+// Wait for user to open serial console
+func waitSerial() {
+	for !machine.Serial.DTR() {
+		time.Sleep(100 * time.Millisecond)
+	}
+}
+
+type UARTx struct {
+	*machine.UART
+}
+
+func (u UARTx) Read(p []byte) (n int, err error) {
+	if u.Buffered() == 0 {
+		time.Sleep(1 * time.Millisecond)
+		return 0, nil
+	}
+	return u.UART.Read(p)
+}

examples/rtl8720dn/mqttsub/main.go

@@ -0,0 +1,154 @@
+// This is a sensor station that uses a RTL8720DN running on the device UART2.
+// It creates an MQTT connection that publishes a message every second
+// to an MQTT broker.
+//
+// In other words:
+// Your computer <--> USB-CDC <--> MCU <--> UART2 <--> RTL8720DN <--> Internet <--> MQTT broker.
+//
+// You must also install the Paho MQTT package to build this program:
+//
+// 		go get -u github.com/eclipse/paho.mqtt.golang
+//
+// You can check that mqttpub/mqttsub is running successfully with the following command.
+//
+// 		mosquitto_sub -h test.mosquitto.org -t tinygo/tx
+// 		mosquitto_pub -h test.mosquitto.org -t tinygo/rx -m "hello world"
+//
+package main
+
+import (
+	"fmt"
+	"math/rand"
+	"time"
+
+	"tinygo.org/x/drivers/net"
+	"tinygo.org/x/drivers/net/mqtt"
+	"tinygo.org/x/drivers/rtl8720dn"
+)
+
+// You can override the setting with the init() in another source code.
+// func init() {
+//    ssid = "your-ssid"
+//    password = "your-password"
+//    debug = true
+//    server = "tinygo.org"
+// }
+
+var (
+	ssid     string
+	password string
+	server   string = "tcp://test.mosquitto.org:1883"
+	debug           = false
+)
+
+var buf [0x400]byte
+
+var lastRequestTime time.Time
+var conn net.Conn
+var adaptor *rtl8720dn.RTL8720DN
+
+func main() {
+	err := run()
+	for err != nil {
+		fmt.Printf("error: %s\r\n", err.Error())
+		time.Sleep(5 * time.Second)
+	}
+}
+
+// change these to connect to a different UART or pins for the ESP8266/ESP32
+var (
+	cl      mqtt.Client
+	topicTx = "tinygo/tx"
+	topicRx = "tinygo/rx"
+)
+
+func subHandler(client mqtt.Client, msg mqtt.Message) {
+	fmt.Printf("[%s]  ", msg.Topic())
+	fmt.Printf("%s\r\n", msg.Payload())
+}
+
+func run() error {
+	rtl, err := setupRTL8720DN()
+	if err != nil {
+		return err
+	}
+	net.UseDriver(rtl)
+
+	err = rtl.ConnectToAccessPoint(ssid, password, 10*time.Second)
+	if err != nil {
+		return err
+	}
+
+	ip, subnet, gateway, err := rtl.GetIP()
+	if err != nil {
+		return err
+	}
+	fmt.Printf("IP Address : %s\r\n", ip)
+	fmt.Printf("Mask       : %s\r\n", subnet)
+	fmt.Printf("Gateway    : %s\r\n", gateway)
+
+	rand.Seed(time.Now().UnixNano())
+
+	opts := mqtt.NewClientOptions()
+	opts.AddBroker(server).SetClientID("tinygo-client-" + randomString(10))
+
+	println("Connecting to MQTT broker at", server)
+	cl = mqtt.NewClient(opts)
+	if token := cl.Connect(); token.Wait() && token.Error() != nil {
+		failMessage(token.Error().Error())
+	}
+
+	// subscribe
+	token := cl.Subscribe(topicRx, 0, subHandler)
+	token.Wait()
+	if token.Error() != nil {
+		failMessage(token.Error().Error())
+	}
+
+	go publishing()
+
+	select {}
+
+	// Right now this code is never reached. Need a way to trigger it...
+	println("Disconnecting MQTT...")
+	cl.Disconnect(100)
+
+	println("Done.")
+
+	return nil
+}
+
+func publishing() {
+	for i := 0; ; i++ {
+		println("Publishing MQTT message...")
+		data := []byte(fmt.Sprintf(`{"e":[{"n":"hello %d","v":101}]}`, i))
+		token := cl.Publish(topicTx, 0, false, data)
+		token.Wait()
+		if token.Error() != nil {
+			println(token.Error().Error())
+		}
+
+		time.Sleep(20 * 100 * time.Millisecond)
+	}
+}
+
+// Returns an int >= min, < max
+func randomInt(min, max int) int {
+	return min + rand.Intn(max-min)
+}
+
+// Generate a random string of A-Z chars with len = l
+func randomString(len int) string {
+	bytes := make([]byte, len)
+	for i := 0; i < len; i++ {
+		bytes[i] = byte(randomInt(65, 90))
+	}
+	return string(bytes)
+}
+
+func failMessage(msg string) {
+	for {
+		println(msg)
+		time.Sleep(1 * time.Second)
+	}
+}

examples/rtl8720dn/mqttsub/wioterminal.go

@@ -0,0 +1,74 @@
+//go:build wioterminal
+// +build wioterminal
+
+package main
+
+import (
+	"device/sam"
+	"machine"
+	"runtime/interrupt"
+	"time"
+
+	"tinygo.org/x/drivers/rtl8720dn"
+)
+
+var (
+	uart UARTx
+)
+
+func handleInterrupt(interrupt.Interrupt) {
+	// should reset IRQ
+	uart.Receive(byte((uart.Bus.DATA.Get() & 0xFF)))
+	uart.Bus.INTFLAG.SetBits(sam.SERCOM_USART_INT_INTFLAG_RXC)
+}
+
+func setupRTL8720DN() (*rtl8720dn.RTL8720DN, error) {
+	machine.RTL8720D_CHIP_PU.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.RTL8720D_CHIP_PU.Low()
+	time.Sleep(100 * time.Millisecond)
+	machine.RTL8720D_CHIP_PU.High()
+	time.Sleep(1000 * time.Millisecond)
+	if debug {
+		waitSerial()
+	}
+
+	uart = UARTx{
+		UART: &machine.UART{
+			Buffer: machine.NewRingBuffer(),
+			Bus:    sam.SERCOM0_USART_INT,
+			SERCOM: 0,
+		},
+	}
+
+	uart.Interrupt = interrupt.New(sam.IRQ_SERCOM0_2, handleInterrupt)
+	uart.Configure(machine.UARTConfig{TX: machine.PB24, RX: machine.PC24, BaudRate: 614400})
+
+	rtl := rtl8720dn.New(uart)
+	rtl.Debug(debug)
+
+	_, err := rtl.Rpc_tcpip_adapter_init()
+	if err != nil {
+		return nil, err
+	}
+
+	return rtl, nil
+}
+
+// Wait for user to open serial console
+func waitSerial() {
+	for !machine.Serial.DTR() {
+		time.Sleep(100 * time.Millisecond)
+	}
+}
+
+type UARTx struct {
+	*machine.UART
+}
+
+func (u UARTx) Read(p []byte) (n int, err error) {
+	if u.Buffered() == 0 {
+		time.Sleep(1 * time.Millisecond)
+		return 0, nil
+	}
+	return u.UART.Read(p)
+}

examples/rtl8720dn/ntpclient/main.go

@@ -0,0 +1,144 @@
+// This is an example of using the rtl8720dn driver to implement a NTP client.
+// It creates a UDP connection to request the current time and parse the
+// response from a NTP server.
+package main
+
+import (
+	"errors"
+	"fmt"
+	"runtime"
+	"time"
+
+	"tinygo.org/x/drivers/net"
+)
+
+// IP address of the server aka "hub". Replace with your own info.
+// You can override the setting with the init() in another source code.
+// func init() {
+//    ssid = "your-ssid"
+//    password = "your-password"
+//    ntpHost = "129.6.15.29"
+//    debug = true
+// }
+
+var (
+	ssid     string
+	password string
+	ntpHost  = "129.6.15.29"
+	debug    = false
+)
+
+const NTP_PACKET_SIZE = 48
+
+var b = make([]byte, NTP_PACKET_SIZE)
+
+func main() {
+	err := run()
+	for err != nil {
+		fmt.Printf("error: %s\r\n", err.Error())
+		time.Sleep(5 * time.Second)
+	}
+}
+
+func run() error {
+	rtl, err := setupRTL8720DN()
+	if err != nil {
+		return err
+	}
+	net.UseDriver(rtl)
+
+	err = rtl.ConnectToAccessPoint(ssid, password, 10*time.Second)
+	if err != nil {
+		return err
+	}
+
+	ip, subnet, gateway, err := rtl.GetIP()
+	if err != nil {
+		return err
+	}
+	fmt.Printf("IP Address : %s\r\n", ip)
+	fmt.Printf("Mask       : %s\r\n", subnet)
+	fmt.Printf("Gateway    : %s\r\n", gateway)
+
+	// now make UDP connection
+	hip := net.ParseIP(ntpHost)
+	raddr := &net.UDPAddr{IP: hip, Port: 123}
+	laddr := &net.UDPAddr{Port: 2390}
+	conn, err := net.DialUDP("udp", laddr, raddr)
+	if err != nil {
+		return err
+	}
+
+	for {
+		// send data
+		println("Requesting NTP time...")
+		t, err := getCurrentTime(conn)
+		if err != nil {
+			message("Error getting current time: %v", err)
+		} else {
+			message("NTP time: %v", t)
+		}
+		runtime.AdjustTimeOffset(-1 * int64(time.Since(t)))
+		for i := 0; i < 10; i++ {
+			message("Current time: %v", time.Now())
+			time.Sleep(1 * time.Second)
+		}
+	}
+
+}
+
+func getCurrentTime(conn *net.UDPSerialConn) (time.Time, error) {
+	if err := sendNTPpacket(conn); err != nil {
+		return time.Time{}, err
+	}
+	clearBuffer()
+	for now := time.Now(); time.Since(now) < time.Second; {
+		time.Sleep(5 * time.Millisecond)
+		if n, err := conn.Read(b); err != nil {
+			return time.Time{}, fmt.Errorf("error reading UDP packet: %w", err)
+		} else if n == 0 {
+			continue // no packet received yet
+		} else if n != NTP_PACKET_SIZE {
+			if n != NTP_PACKET_SIZE {
+				return time.Time{}, fmt.Errorf("expected NTP packet size of %d: %d", NTP_PACKET_SIZE, n)
+			}
+		}
+		return parseNTPpacket(), nil
+	}
+	return time.Time{}, errors.New("no packet received after 1 second")
+}
+
+func sendNTPpacket(conn *net.UDPSerialConn) error {
+	clearBuffer()
+	b[0] = 0b11100011 // LI, Version, Mode
+	b[1] = 0          // Stratum, or type of clock
+	b[2] = 6          // Polling Interval
+	b[3] = 0xEC       // Peer Clock Precision
+	// 8 bytes of zero for Root Delay & Root Dispersion
+	b[12] = 49
+	b[13] = 0x4E
+	b[14] = 49
+	b[15] = 52
+	if _, err := conn.Write(b); err != nil {
+		return err
+	}
+	return nil
+}
+
+func parseNTPpacket() time.Time {
+	// the timestamp starts at byte 40 of the received packet and is four bytes,
+	// this is NTP time (seconds since Jan 1 1900):
+	t := uint32(b[40])<<24 | uint32(b[41])<<16 | uint32(b[42])<<8 | uint32(b[43])
+	const seventyYears = 2208988800
+	return time.Unix(int64(t-seventyYears), 0)
+}
+
+func clearBuffer() {
+	for i := range b {
+		b[i] = 0
+	}
+}
+
+func message(format string, args ...interface{}) {
+	println(fmt.Sprintf(format, args...), "\r")
+}

examples/rtl8720dn/ntpclient/wioterminal.go

@@ -0,0 +1,72 @@
+//go:build wioterminal
+// +build wioterminal
+
+package main
+
+import (
+	"device/sam"
+	"machine"
+	"runtime/interrupt"
+	"time"
+
+	"tinygo.org/x/drivers/rtl8720dn"
+)
+
+var (
+	uart UARTx
+)
+
+func handleInterrupt(interrupt.Interrupt) {
+	// should reset IRQ
+	uart.Receive(byte((uart.Bus.DATA.Get() & 0xFF)))
+	uart.Bus.INTFLAG.SetBits(sam.SERCOM_USART_INT_INTFLAG_RXC)
+}
+
+func setupRTL8720DN() (*rtl8720dn.RTL8720DN, error) {
+	machine.RTL8720D_CHIP_PU.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.RTL8720D_CHIP_PU.Low()
+	time.Sleep(100 * time.Millisecond)
+	machine.RTL8720D_CHIP_PU.High()
+	time.Sleep(1000 * time.Millisecond)
+	waitSerial()
+
+	uart = UARTx{
+		UART: &machine.UART{
+			Buffer: machine.NewRingBuffer(),
+			Bus:    sam.SERCOM0_USART_INT,
+			SERCOM: 0,
+		},
+	}
+
+	uart.Interrupt = interrupt.New(sam.IRQ_SERCOM0_2, handleInterrupt)
+	uart.Configure(machine.UARTConfig{TX: machine.PB24, RX: machine.PC24, BaudRate: 614400})
+
+	rtl := rtl8720dn.New(uart)
+	rtl.Debug(debug)
+
+	_, err := rtl.Rpc_tcpip_adapter_init()
+	if err != nil {
+		return nil, err
+	}
+
+	return rtl, nil
+}
+
+// Wait for user to open serial console
+func waitSerial() {
+	for !machine.Serial.DTR() {
+		time.Sleep(100 * time.Millisecond)
+	}
+}
+
+type UARTx struct {
+	*machine.UART
+}
+
+func (u UARTx) Read(p []byte) (n int, err error) {
+	if u.Buffered() == 0 {
+		time.Sleep(1 * time.Millisecond)
+		return 0, nil
+	}
+	return u.UART.Read(p)
+}

examples/rtl8720dn/tcpclient/main.go

@@ -0,0 +1,121 @@
+// This example opens a TCP connection using a device with RTL8720DN firmware
+// and sends some data, for the purpose of testing speed and connectivity.
+//
+// You can open a server to accept connections from this program using:
+//
+// nc -w 5 -lk 8080
+//
+package main
+
+import (
+	"bytes"
+	"fmt"
+	"time"
+
+	"tinygo.org/x/drivers/net"
+)
+
+// You can override the setting with the init() in another source code.
+// func init() {
+//    ssid = "sghome-gw"
+//    password = "3af25537b4524"
+//    serverIP = "192.168.1.119"
+//    debug = true
+// }
+
+var (
+	ssid     string
+	password string
+	serverIP = ""
+	debug    = false
+)
+
+var buf = &bytes.Buffer{}
+
+func main() {
+	err := run()
+	for err != nil {
+		fmt.Printf("error: %s\r\n", err.Error())
+		time.Sleep(5 * time.Second)
+	}
+}
+
+func run() error {
+	rtl, err := setupRTL8720DN()
+	if err != nil {
+		return err
+	}
+	net.UseDriver(rtl)
+
+	err = rtl.ConnectToAccessPoint(ssid, password, 10*time.Second)
+	if err != nil {
+		return err
+	}
+
+	ip, subnet, gateway, err := rtl.GetIP()
+	if err != nil {
+		return err
+	}
+	fmt.Printf("IP Address : %s\r\n", ip)
+	fmt.Printf("Mask       : %s\r\n", subnet)
+	fmt.Printf("Gateway    : %s\r\n", gateway)
+
+	for {
+		sendBatch()
+		time.Sleep(500 * time.Millisecond)
+	}
+	println("Done.")
+
+	return nil
+}
+
+func sendBatch() {
+
+	// make TCP connection
+	ip := net.ParseIP(serverIP)
+	raddr := &net.TCPAddr{IP: ip, Port: 8080}
+	laddr := &net.TCPAddr{Port: 8080}
+
+	message("---------------\r\nDialing TCP connection")
+	conn, err := net.DialTCP("tcp", laddr, raddr)
+	for ; err != nil; conn, err = net.DialTCP("tcp", laddr, raddr) {
+		message(err.Error())
+		time.Sleep(5 * time.Second)
+	}
+
+	n := 0
+	w := 0
+	start := time.Now()
+
+	// send data
+	message("Sending data")
+
+	for i := 0; i < 1000; i++ {
+		buf.Reset()
+		fmt.Fprint(buf,
+			"\r---------------------------- i == ", i, " ----------------------------"+
+				"\r---------------------------- i == ", i, " ----------------------------")
+		if w, err = conn.Write(buf.Bytes()); err != nil {
+			println("error:", err.Error(), "\r")
+			continue
+		}
+		n += w
+	}
+
+	buf.Reset()
+	ms := time.Now().Sub(start).Milliseconds()
+	fmt.Fprint(buf, "\nWrote ", n, " bytes in ", ms, " ms\r\n")
+	message(buf.String())
+
+	if _, err := conn.Write(buf.Bytes()); err != nil {
+		println("error:", err.Error(), "\r")
+	}
+
+	// Right now this code is never reached. Need a way to trigger it...
+	println("Disconnecting TCP...")
+	conn.Close()
+}
+
+func message(msg string) {
+	println(msg, "\r")
+}

examples/rtl8720dn/tcpclient/wioterminal.go

@@ -0,0 +1,72 @@
+//go:build wioterminal
+// +build wioterminal
+
+package main
+
+import (
+	"device/sam"
+	"machine"
+	"runtime/interrupt"
+	"time"
+
+	"tinygo.org/x/drivers/rtl8720dn"
+)
+
+var (
+	uart UARTx
+)
+
+func handleInterrupt(interrupt.Interrupt) {
+	// should reset IRQ
+	uart.Receive(byte((uart.Bus.DATA.Get() & 0xFF)))
+	uart.Bus.INTFLAG.SetBits(sam.SERCOM_USART_INT_INTFLAG_RXC)
+}
+
+func setupRTL8720DN() (*rtl8720dn.RTL8720DN, error) {
+	machine.RTL8720D_CHIP_PU.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.RTL8720D_CHIP_PU.Low()
+	time.Sleep(100 * time.Millisecond)
+	machine.RTL8720D_CHIP_PU.High()
+	time.Sleep(1000 * time.Millisecond)
+	waitSerial()
+
+	uart = UARTx{
+		UART: &machine.UART{
+			Buffer: machine.NewRingBuffer(),
+			Bus:    sam.SERCOM0_USART_INT,
+			SERCOM: 0,
+		},
+	}
+
+	uart.Interrupt = interrupt.New(sam.IRQ_SERCOM0_2, handleInterrupt)
+	uart.Configure(machine.UARTConfig{TX: machine.PB24, RX: machine.PC24, BaudRate: 614400})
+
+	rtl := rtl8720dn.New(uart)
+	rtl.Debug(debug)
+
+	_, err := rtl.Rpc_tcpip_adapter_init()
+	if err != nil {
+		return nil, err
+	}
+
+	return rtl, nil
+}
+
+// Wait for user to open serial console
+func waitSerial() {
+	for !machine.Serial.DTR() {
+		time.Sleep(100 * time.Millisecond)
+	}
+}
+
+type UARTx struct {
+	*machine.UART
+}
+
+func (u UARTx) Read(p []byte) (n int, err error) {
+	if u.Buffered() == 0 {
+		time.Sleep(1 * time.Millisecond)
+		return 0, nil
+	}
+	return u.UART.Read(p)
+}

examples/rtl8720dn/tlsclient/main.go

@@ -0,0 +1,137 @@
+package main
+
+import (
+	"bufio"
+	"fmt"
+	"strings"
+	"time"
+
+	"tinygo.org/x/drivers/net"
+	"tinygo.org/x/drivers/net/http"
+	"tinygo.org/x/drivers/rtl8720dn"
+)
+
+// You can override the setting with the init() in another source code.
+// func init() {
+//    ssid = "your-ssid"
+//    password = "your-password"
+//    debug = true
+//    url = "https://www.example.com"
+//    test_root_ca = "..."
+// }
+
+var (
+	ssid     string
+	password string
+	url      string = "https://www.example.com"
+	debug           = false
+)
+
+// Set the test_root_ca created by the following command
+// $ openssl s_client -showcerts -verify 5 -connect www.example.com:443 < /dev/null
+var test_root_ca = `-----BEGIN CERTIFICATE-----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+-----END CERTIFICATE-----
+`
+
+var buf [0x1000]byte
+
+var lastRequestTime time.Time
+var conn net.Conn
+var adaptor *rtl8720dn.RTL8720DN
+
+func main() {
+	err := run()
+	for err != nil {
+		fmt.Printf("error: %s\r\n", err.Error())
+		time.Sleep(5 * time.Second)
+	}
+}
+
+func run() error {
+	rtl, err := setupRTL8720DN()
+	if err != nil {
+		return err
+	}
+	rtl.SetRootCA(&test_root_ca)
+	net.UseDriver(rtl)
+	http.SetBuf(buf[:])
+
+	err = rtl.ConnectToAccessPoint(ssid, password, 10*time.Second)
+	if err != nil {
+		return err
+	}
+
+	ip, subnet, gateway, err := rtl.GetIP()
+	if err != nil {
+		return err
+	}
+	fmt.Printf("IP Address : %s\r\n", ip)
+	fmt.Printf("Mask       : %s\r\n", subnet)
+	fmt.Printf("Gateway    : %s\r\n", gateway)
+
+	// You can send and receive cookies in the following way
+	// 	import "tinygo.org/x/drivers/net/http/cookiejar"
+	// 	jar, err := cookiejar.New(nil)
+	// 	if err != nil {
+	// 		return err
+	// 	}
+	// 	client := &http.Client{Jar: jar}
+	// 	http.DefaultClient = client
+
+	cnt := 0
+	for {
+		// Various examples are as follows
+		//
+		// -- Get
+		// 	resp, err := http.Get(url)
+		//
+		// -- Post
+		// 	body := `cnt=12`
+		// 	resp, err = http.Post(url, "application/x-www-form-urlencoded", strings.NewReader(body))
+		//
+		// -- Post with JSON
+		// 	body := `{"msg": "hello"}`
+		// 	resp, err := http.Post(url, "application/json", strings.NewReader(body))
+
+		resp, err := http.Get(url)
+		if err != nil {
+			return err
+		}
+
+		fmt.Printf("%s %s\r\n", resp.Proto, resp.Status)
+		for k, v := range resp.Header {
+			fmt.Printf("%s: %s\r\n", k, strings.Join(v, " "))
+		}
+		fmt.Printf("\r\n")
+
+		scanner := bufio.NewScanner(resp.Body)
+		for scanner.Scan() {
+			fmt.Printf("%s\r\n", scanner.Text())
+		}
+		resp.Body.Close()
+
+		cnt++
+		fmt.Printf("-------- %d --------\r\n", cnt)
+		time.Sleep(10 * time.Second)
+	}
+}

examples/rtl8720dn/tlsclient/wioterminal.go

@@ -0,0 +1,72 @@
+//go:build wioterminal
+// +build wioterminal
+
+package main
+
+import (
+	"device/sam"
+	"machine"
+	"runtime/interrupt"
+	"time"
+
+	"tinygo.org/x/drivers/rtl8720dn"
+)
+
+var (
+	uart UARTx
+)
+
+func handleInterrupt(interrupt.Interrupt) {
+	// should reset IRQ
+	uart.Receive(byte((uart.Bus.DATA.Get() & 0xFF)))
+	uart.Bus.INTFLAG.SetBits(sam.SERCOM_USART_INT_INTFLAG_RXC)
+}
+
+func setupRTL8720DN() (*rtl8720dn.RTL8720DN, error) {
+	machine.RTL8720D_CHIP_PU.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.RTL8720D_CHIP_PU.Low()
+	time.Sleep(100 * time.Millisecond)
+	machine.RTL8720D_CHIP_PU.High()
+	time.Sleep(1000 * time.Millisecond)
+	waitSerial()
+
+	uart = UARTx{
+		UART: &machine.UART{
+			Buffer: machine.NewRingBuffer(),
+			Bus:    sam.SERCOM0_USART_INT,
+			SERCOM: 0,
+		},
+	}
+
+	uart.Interrupt = interrupt.New(sam.IRQ_SERCOM0_2, handleInterrupt)
+	uart.Configure(machine.UARTConfig{TX: machine.PB24, RX: machine.PC24, BaudRate: 614400})
+
+	rtl := rtl8720dn.New(uart)
+	rtl.Debug(debug)
+
+	_, err := rtl.Rpc_tcpip_adapter_init()
+	if err != nil {
+		return nil, err
+	}
+
+	return rtl, nil
+}
+
+// Wait for user to open serial console
+func waitSerial() {
+	for !machine.Serial.DTR() {
+		time.Sleep(100 * time.Millisecond)
+	}
+}
+
+type UARTx struct {
+	*machine.UART
+}
+
+func (u UARTx) Read(p []byte) (n int, err error) {
+	if u.Buffered() == 0 {
+		time.Sleep(1 * time.Millisecond)
+		return 0, nil
+	}
+	return u.UART.Read(p)
+}

examples/rtl8720dn/udpstation/main.go

@@ -0,0 +1,89 @@
+package main
+
+import (
+	"fmt"
+	"strconv"
+	"time"
+
+	"tinygo.org/x/drivers/net"
+	"tinygo.org/x/drivers/net/http"
+)
+
+// IP address of the server aka "hub". Replace with your own info.
+// You can override the setting with the init() in another source code.
+// func init() {
+//    ssid = "your-ssid"
+//    password = "your-password"
+//    hubIP = "192.168.1.118"
+//    debug = true
+// }
+
+var (
+	ssid     string
+	password string
+	hubIP    = ""
+	debug    = false
+)
+
+var buf [0x400]byte
+
+func main() {
+	err := run()
+	for err != nil {
+		fmt.Printf("error: %s\r\n", err.Error())
+		time.Sleep(5 * time.Second)
+	}
+}
+
+func run() error {
+	rtl, err := setupRTL8720DN()
+	if err != nil {
+		return err
+	}
+	net.UseDriver(rtl)
+	http.SetBuf(buf[:])
+
+	err = rtl.ConnectToAccessPoint(ssid, password, 10*time.Second)
+	if err != nil {
+		return err
+	}
+
+	ip, subnet, gateway, err := rtl.GetIP()
+	if err != nil {
+		return err
+	}
+	fmt.Printf("IP Address : %s\r\n", ip)
+	fmt.Printf("Mask       : %s\r\n", subnet)
+	fmt.Printf("Gateway    : %s\r\n", gateway)
+
+	// now make UDP connection
+	hip := net.ParseIP(hubIP)
+	raddr := &net.UDPAddr{IP: hip, Port: 2222}
+	laddr := &net.UDPAddr{Port: 2222}
+
+	println("Dialing UDP connection...")
+	conn, err := net.DialUDP("udp", laddr, raddr)
+	if err != nil {
+		return err
+	}
+
+	for {
+		// send data
+		println("Sending data...")
+		for i := 0; i < 25; i++ {
+			conn.Write([]byte("hello " + strconv.Itoa(i) + "\r\n"))
+		}
+		time.Sleep(1000 * time.Millisecond)
+	}
+
+	// Right now this code is never reached. Need a way to trigger it...
+	println("Disconnecting UDP...")
+	conn.Close()
+	println("Done.")
+
+	return nil
+}
+
+func message(msg string) {
+	println(msg, "\r")
+}

examples/rtl8720dn/udpstation/wioterminal.go

@@ -0,0 +1,72 @@
+//go:build wioterminal
+// +build wioterminal
+
+package main
+
+import (
+	"device/sam"
+	"machine"
+	"runtime/interrupt"
+	"time"
+
+	"tinygo.org/x/drivers/rtl8720dn"
+)
+
+var (
+	uart UARTx
+)
+
+func handleInterrupt(interrupt.Interrupt) {
+	// should reset IRQ
+	uart.Receive(byte((uart.Bus.DATA.Get() & 0xFF)))
+	uart.Bus.INTFLAG.SetBits(sam.SERCOM_USART_INT_INTFLAG_RXC)
+}
+
+func setupRTL8720DN() (*rtl8720dn.RTL8720DN, error) {
+	machine.RTL8720D_CHIP_PU.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.RTL8720D_CHIP_PU.Low()
+	time.Sleep(100 * time.Millisecond)
+	machine.RTL8720D_CHIP_PU.High()
+	time.Sleep(1000 * time.Millisecond)
+	waitSerial()
+
+	uart = UARTx{
+		UART: &machine.UART{
+			Buffer: machine.NewRingBuffer(),
+			Bus:    sam.SERCOM0_USART_INT,
+			SERCOM: 0,
+		},
+	}
+
+	uart.Interrupt = interrupt.New(sam.IRQ_SERCOM0_2, handleInterrupt)
+	uart.Configure(machine.UARTConfig{TX: machine.PB24, RX: machine.PC24, BaudRate: 614400})
+
+	rtl := rtl8720dn.New(uart)
+	rtl.Debug(debug)
+
+	_, err := rtl.Rpc_tcpip_adapter_init()
+	if err != nil {
+		return nil, err
+	}
+
+	return rtl, nil
+}
+
+// Wait for user to open serial console
+func waitSerial() {
+	for !machine.Serial.DTR() {
+		time.Sleep(100 * time.Millisecond)
+	}
+}
+
+type UARTx struct {
+	*machine.UART
+}
+
+func (u UARTx) Read(p []byte) (n int, err error) {
+	if u.Buffered() == 0 {
+		time.Sleep(1 * time.Millisecond)
+		return 0, nil
+	}
+	return u.UART.Read(p)
+}

examples/rtl8720dn/webclient-tinyterm/main.go

@@ -0,0 +1,136 @@
+package main
+
+import (
+	"bufio"
+	"fmt"
+	"image/color"
+	"strings"
+	"time"
+
+	"tinygo.org/x/drivers/net"
+	"tinygo.org/x/drivers/net/http"
+	"tinygo.org/x/tinyfont/proggy"
+	"tinygo.org/x/tinyterm"
+)
+
+// You can override the setting with the init() in another source code.
+// If debug is enabled, a serial connection is required.
+// func init() {
+//    ssid = "your-ssid"
+//    password = "your-password"
+//    debug = false // true
+//    server = "tinygo.org"
+// }
+
+var (
+	ssid     string
+	password string
+	url      = "http://tinygo.org/"
+	debug    = false
+)
+
+var (
+	terminal = tinyterm.NewTerminal(display)
+
+	black = color.RGBA{0, 0, 0, 255}
+	white = color.RGBA{255, 255, 255, 255}
+	red   = color.RGBA{255, 0, 0, 255}
+	blue  = color.RGBA{0, 0, 255, 255}
+	green = color.RGBA{0, 255, 0, 255}
+
+	font = &proggy.TinySZ8pt7b
+)
+
+var buf [0x400]byte
+
+func main() {
+	display.FillScreen(black)
+	backlight.High()
+
+	terminal.Configure(&tinyterm.Config{
+		Font:       font,
+		FontHeight: 10,
+		FontOffset: 6,
+	})
+
+	err := run()
+	for err != nil {
+		fmt.Fprintf(terminal, "error: %s\r\n", err.Error())
+		time.Sleep(5 * time.Second)
+	}
+}
+
+func run() error {
+	fmt.Fprintf(terminal, "setupRTL8720DN()\r\n")
+	if debug {
+		fmt.Fprintf(terminal, "Running in debug mode.\r\n")
+		fmt.Fprintf(terminal, "A serial connection is required to continue execution.\r\n")
+	}
+	rtl, err := setupRTL8720DN()
+	if err != nil {
+		return err
+	}
+	net.UseDriver(rtl)
+	http.SetBuf(buf[:])
+
+	fmt.Fprintf(terminal, "ConnectToAP()\r\n")
+	err = rtl.ConnectToAccessPoint(ssid, password, 10*time.Second)
+	if err != nil {
+		return err
+	}
+	fmt.Fprintf(terminal, "connected\r\n\r\n")
+
+	ip, subnet, gateway, err := rtl.GetIP()
+	if err != nil {
+		return err
+	}
+	fmt.Fprintf(terminal, "IP Address : %s\r\n", ip)
+	fmt.Fprintf(terminal, "Mask       : %s\r\n", subnet)
+	fmt.Fprintf(terminal, "Gateway    : %s\r\n", gateway)
+
+	// You can send and receive cookies in the following way
+	// 	import "tinygo.org/x/drivers/net/http/cookiejar"
+	// 	jar, err := cookiejar.New(nil)
+	// 	if err != nil {
+	// 		return err
+	// 	}
+	// 	client := &http.Client{Jar: jar}
+	// 	http.DefaultClient = client
+
+	cnt := 0
+	for {
+		// Various examples are as follows
+		//
+		// -- Get
+		// 	resp, err := http.Get(url)
+		//
+		// -- Post
+		// 	body := `cnt=12`
+		// 	resp, err = http.Post(url, "application/x-www-form-urlencoded", strings.NewReader(body))
+		//
+		// -- Post with JSON
+		// 	body := `{"msg": "hello"}`
+		// 	resp, err := http.Post(url, "application/json", strings.NewReader(body))
+
+		resp, err := http.Get(url)
+		if err != nil {
+			return err
+		}
+
+		fmt.Fprintf(terminal, "%s %s\r\n", resp.Proto, resp.Status)
+		for k, v := range resp.Header {
+			fmt.Fprintf(terminal, "%s: %s\r\n", k, strings.Join(v, " "))
+		}
+		fmt.Printf("\r\n")
+
+		scanner := bufio.NewScanner(resp.Body)
+		for scanner.Scan() {
+			fmt.Fprintf(terminal, "%s\r\n", scanner.Text())
+		}
+		resp.Body.Close()
+
+		cnt++
+		fmt.Fprintf(terminal, "-------- %d --------\r\n", cnt)
+		time.Sleep(10 * time.Second)
+	}
+}

examples/rtl8720dn/webclient-tinyterm/wioterminal.go

@@ -0,0 +1,98 @@
+//go:build wioterminal
+// +build wioterminal
+
+package main
+
+import (
+	"device/sam"
+	"machine"
+	"runtime/interrupt"
+	"time"
+
+	"tinygo.org/x/drivers/ili9341"
+	"tinygo.org/x/drivers/rtl8720dn"
+)
+
+var (
+	uart UARTx
+)
+
+var (
+	display = ili9341.NewSPI(
+		machine.SPI3,
+		machine.LCD_DC,
+		machine.LCD_SS_PIN,
+		machine.LCD_RESET,
+	)
+
+	backlight = machine.LCD_BACKLIGHT
+)
+
+func init() {
+	machine.SPI3.Configure(machine.SPIConfig{
+		SCK:       machine.LCD_SCK_PIN,
+		SDO:       machine.LCD_SDO_PIN,
+		SDI:       machine.LCD_SDI_PIN,
+		Frequency: 40000000,
+	})
+	display.Configure(ili9341.Config{})
+
+	backlight.Configure(machine.PinConfig{machine.PinOutput})
+}
+
+func handleInterrupt(interrupt.Interrupt) {
+	// should reset IRQ
+	uart.Receive(byte((uart.Bus.DATA.Get() & 0xFF)))
+	uart.Bus.INTFLAG.SetBits(sam.SERCOM_USART_INT_INTFLAG_RXC)
+}
+
+func setupRTL8720DN() (*rtl8720dn.RTL8720DN, error) {
+	machine.RTL8720D_CHIP_PU.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.RTL8720D_CHIP_PU.Low()
+	time.Sleep(100 * time.Millisecond)
+	machine.RTL8720D_CHIP_PU.High()
+	time.Sleep(1000 * time.Millisecond)
+	if debug {
+		waitSerial()
+	}
+
+	uart = UARTx{
+		UART: &machine.UART{
+			Buffer: machine.NewRingBuffer(),
+			Bus:    sam.SERCOM0_USART_INT,
+			SERCOM: 0,
+		},
+	}
+
+	uart.Interrupt = interrupt.New(sam.IRQ_SERCOM0_2, handleInterrupt)
+	uart.Configure(machine.UARTConfig{TX: machine.PB24, RX: machine.PC24, BaudRate: 614400})
+
+	rtl := rtl8720dn.New(uart)
+	rtl.Debug(debug)
+
+	_, err := rtl.Rpc_tcpip_adapter_init()
+	if err != nil {
+		return nil, err
+	}
+
+	return rtl, nil
+}
+
+// Wait for user to open serial console
+func waitSerial() {
+	for !machine.Serial.DTR() {
+		time.Sleep(100 * time.Millisecond)
+	}
+}
+
+type UARTx struct {
+	*machine.UART
+}
+
+func (u UARTx) Read(p []byte) (n int, err error) {
+	if u.Buffered() == 0 {
+		time.Sleep(1 * time.Millisecond)
+		return 0, nil
+	}
+	return u.UART.Read(p)
+}

examples/rtl8720dn/webclient/main.go

@@ -0,0 +1,104 @@
+package main
+
+import (
+	"bufio"
+	"fmt"
+	"strings"
+	"time"
+
+	"tinygo.org/x/drivers/net"
+	"tinygo.org/x/drivers/net/http"
+)
+
+// You can override the setting with the init() in another source code.
+// func init() {
+//    ssid = "your-ssid"
+//    password = "your-password"
+//    url = "http://tinygo.org/"
+//    debug = true
+// }
+
+var (
+	ssid     string
+	password string
+	url      = "http://tinygo.org/"
+	debug    = false
+)
+
+var buf [0x400]byte
+
+func main() {
+	err := run()
+	for err != nil {
+		fmt.Printf("error: %s\r\n", err.Error())
+		time.Sleep(5 * time.Second)
+	}
+}
+
+func run() error {
+	rtl, err := setupRTL8720DN()
+	if err != nil {
+		return err
+	}
+	net.UseDriver(rtl)
+	http.SetBuf(buf[:])
+
+	err = rtl.ConnectToAccessPoint(ssid, password, 10*time.Second)
+	if err != nil {
+		return err
+	}
+
+	ip, subnet, gateway, err := rtl.GetIP()
+	if err != nil {
+		return err
+	}
+	fmt.Printf("IP Address : %s\r\n", ip)
+	fmt.Printf("Mask       : %s\r\n", subnet)
+	fmt.Printf("Gateway    : %s\r\n", gateway)
+
+	// You can send and receive cookies in the following way
+	// 	import "tinygo.org/x/drivers/net/http/cookiejar"
+	// 	jar, err := cookiejar.New(nil)
+	// 	if err != nil {
+	// 		return err
+	// 	}
+	// 	client := &http.Client{Jar: jar}
+	// 	http.DefaultClient = client
+
+	cnt := 0
+	for {
+		// Various examples are as follows
+		//
+		// -- Get
+		// 	resp, err := http.Get(url)
+		//
+		// -- Post
+		// 	body := `cnt=12`
+		// 	resp, err = http.Post(url, "application/x-www-form-urlencoded", strings.NewReader(body))
+		//
+		// -- Post with JSON
+		// 	body := `{"msg": "hello"}`
+		// 	resp, err := http.Post(url, "application/json", strings.NewReader(body))
+
+		resp, err := http.Get(url)
+		if err != nil {
+			return err
+		}
+
+		fmt.Printf("%s %s\r\n", resp.Proto, resp.Status)
+		for k, v := range resp.Header {
+			fmt.Printf("%s: %s\r\n", k, strings.Join(v, " "))
+		}
+		fmt.Printf("\r\n")
+
+		scanner := bufio.NewScanner(resp.Body)
+		for scanner.Scan() {
+			fmt.Printf("%s\r\n", scanner.Text())
+		}
+		resp.Body.Close()
+
+		cnt++
+		fmt.Printf("-------- %d --------\r\n", cnt)
+		time.Sleep(10 * time.Second)
+	}
+}

examples/rtl8720dn/webclient/wioterminal.go

@@ -0,0 +1,72 @@
+//go:build wioterminal
+// +build wioterminal
+
+package main
+
+import (
+	"device/sam"
+	"machine"
+	"runtime/interrupt"
+	"time"
+
+	"tinygo.org/x/drivers/rtl8720dn"
+)
+
+var (
+	uart UARTx
+)
+
+func handleInterrupt(interrupt.Interrupt) {
+	// should reset IRQ
+	uart.Receive(byte((uart.Bus.DATA.Get() & 0xFF)))
+	uart.Bus.INTFLAG.SetBits(sam.SERCOM_USART_INT_INTFLAG_RXC)
+}
+
+func setupRTL8720DN() (*rtl8720dn.RTL8720DN, error) {
+	machine.RTL8720D_CHIP_PU.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.RTL8720D_CHIP_PU.Low()
+	time.Sleep(100 * time.Millisecond)
+	machine.RTL8720D_CHIP_PU.High()
+	time.Sleep(1000 * time.Millisecond)
+	waitSerial()
+
+	uart = UARTx{
+		UART: &machine.UART{
+			Buffer: machine.NewRingBuffer(),
+			Bus:    sam.SERCOM0_USART_INT,
+			SERCOM: 0,
+		},
+	}
+
+	uart.Interrupt = interrupt.New(sam.IRQ_SERCOM0_2, handleInterrupt)
+	uart.Configure(machine.UARTConfig{TX: machine.PB24, RX: machine.PC24, BaudRate: 614400})
+
+	rtl := rtl8720dn.New(uart)
+	rtl.Debug(debug)
+
+	_, err := rtl.Rpc_tcpip_adapter_init()
+	if err != nil {
+		return nil, err
+	}
+
+	return rtl, nil
+}
+
+// Wait for user to open serial console
+func waitSerial() {
+	for !machine.Serial.DTR() {
+		time.Sleep(100 * time.Millisecond)
+	}
+}
+
+type UARTx struct {
+	*machine.UART
+}
+
+func (u UARTx) Read(p []byte) (n int, err error) {
+	if u.Buffered() == 0 {
+		time.Sleep(1 * time.Millisecond)
+		return 0, nil
+	}
+	return u.UART.Read(p)
+}

examples/rtl8720dn/webserver/main.go

@@ -0,0 +1,192 @@
+package main
+
+import (
+	"fmt"
+	"machine"
+	"strconv"
+	"time"
+
+	"tinygo.org/x/drivers/net/http"
+)
+
+// You can override the setting with the init() in another source code.
+// func init() {
+//    ssid = "your-ssid"
+//    password = "your-password"
+//    debug = true
+// }
+
+var (
+	ssid     string
+	password string
+	debug    = false
+)
+
+var led = machine.LED
+var backlight = machine.LCD_BACKLIGHT
+
+func main() {
+	led.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	backlight.Configure(machine.PinConfig{Mode: machine.PinOutput})
+
+	err := run()
+	for err != nil {
+		fmt.Printf("error: %s\r\n", err.Error())
+		time.Sleep(5 * time.Second)
+	}
+}
+
+func run() error {
+	rtl, err := setupRTL8720DN()
+	if err != nil {
+		return err
+	}
+	http.UseDriver(rtl)
+
+	err = rtl.ConnectToAccessPoint(ssid, password, 10*time.Second)
+	if err != nil {
+		return err
+	}
+
+	ip, subnet, gateway, err := rtl.GetIP()
+	if err != nil {
+		return err
+	}
+	fmt.Printf("IP Address : %s\r\n", ip)
+	fmt.Printf("Mask       : %s\r\n", subnet)
+	fmt.Printf("Gateway    : %s\r\n", gateway)
+
+	http.HandleFunc("/", root)
+	http.HandleFunc("/hello", hello)
+	http.HandleFunc("/cnt", cnt)
+	http.HandleFunc("/6", sixlines)
+	http.HandleFunc("/off", LED_OFF)
+	http.HandleFunc("/on", LED_ON)
+	if err := http.ListenAndServe(":80", nil); err != nil {
+		message(err.Error())
+	}
+	return nil
+}
+
+func root(w http.ResponseWriter, r *http.Request) {
+	access := 1
+
+	cookie, err := r.Cookie("access")
+	if err != nil {
+		if err == http.ErrNoCookie {
+			cookie = &http.Cookie{
+				Name:  "access",
+				Value: "1",
+			}
+		} else {
+			http.Error(w, fmt.Sprintf("%s", err.Error()), http.StatusBadRequest)
+			return
+		}
+	} else {
+		v, err := strconv.ParseInt(cookie.Value, 10, 0)
+		if err != nil {
+			http.Error(w, fmt.Sprintf("invalid cookie.Value : %s", cookie.Value), http.StatusBadRequest)
+			return
+		}
+		cookie.Value = fmt.Sprintf("%d", v+1)
+		access = int(v) + 1
+	}
+	http.SetCookie(w, cookie)
+	w.WriteHeader(http.StatusOK)
+
+	fmt.Fprintf(w, `
+<html>
+<head>
+    <title>TinyGo HTTP Server</title>
+    <script language="javascript" type="text/javascript">
+        var counter = 0
+        function ledOn() { fetch("/on").then(response => response.text()).then(text => { led.innerHTML = "<p>on</p>"; }); }
+        function ledOff() { fetch("/off").then(response => response.text()).then(text => { led.innerHTML = "<p>off</p>"; }); }
+        function fetchCnt() { fetch("/cnt").then(response => response.json()).then(json => { counter = json.cnt; cnt.innerHTML = counter; }); }
+        function incrCnt() { counter = counter + 1; fetch("/cnt?cnt=" + counter, { method: 'POST' }).then(response => response.json()).then(json => { counter = json.cnt; cnt.innerHTML = counter; }); }
+        function setCnt() { fetch("/cnt", {
+            method: "POST",
+            body: "cnt=" + document.getElementsByName("cnt")[0].value,
+            headers: { 'Content-Type': 'application/x-www-form-urlencoded' },
+        }).then(response => response.json()).then(json => { counter = json.cnt; cnt.innerHTML = counter; }); return false; }
+        function onLoad() { fetchCnt(); }
+    </script>
+</head>
+<body onLoad="onLoad()">
+    <h5>TinyGo HTTP Server</h5>
+
+    <p>
+        access: %d
+    </p>
+
+    <a href="/hello">/hello</a><br>
+    <a href="/6">/6</a><br>
+
+    <p>
+        LED<br>
+        <a href="javascript:ledOn();">/on</a><br>
+        <a href="javascript:ledOff();">/off</a><br>
+    </p>
+
+
+    <p>
+        <a href="/cnt">/cnt</a><br>
+        cnt: <span id="cnt"></span><br>
+        <a href="javascript:incrCnt()">incrCnt()</a><br>
+        <form id="form1" style="display: inline" onSubmit="return setCnt()">
+        <input type="text" name="cnt">
+        <input type="button" value="set cnt", onClick="setCnt()">
+        </form>
+    </p>
+</body>
+</html>
+    `, access)
+}
+
+func sixlines(w http.ResponseWriter, r *http.Request) {
+	// https://fukuno.jig.jp/3267
+	fmt.Fprint(w, `<body onload='onkeydown=e=>K=parseInt(e.key[5]||6,28)/3-8;Z=X=[B=A=12];Y=_=>`+
+		`{for(C=[q=c=i=4];f=i--*K;c-=!Z[h+(K+6?p+K:C[i]=p*A-(p/9|0)*145)])p=B[i];for(c?0:K+6?h+=K:B=C;`+
+		`i=K=q--;f+=Z[A+p])X[p=h+B[q]]=1;h+=A;if(f|B)for(Z=X,X=[l=228],B=[[-7,-20,6,h=17,-9,3,3][t=++t%7]-4,0,1,t-6?-A:2];l--;)`+
+		`for(l%A?l-=l%A*!Z[l]:(P++,c=l+=A);--c>A;)Z[c]=Z[c-A];for(S="";i<240;S+=X[i]|(X[i]=Z[i]|=++i%A<2|i>228)?i%A?"■":"■<br>":"　");`+
+		`D.innerHTML=S+P;setTimeout(Y,i-P)};Y(h=K=t=P=0)'id=D>`)
+}
+
+func LED_ON(w http.ResponseWriter, r *http.Request) {
+	led.High()
+	backlight.High()
+	w.Header().Set(`Content-Type`, `text/plain; charset=UTF-8`)
+	fmt.Fprintf(w, "led.High()")
+}
+
+func LED_OFF(w http.ResponseWriter, r *http.Request) {
+	led.Low()
+	backlight.Low()
+	w.Header().Set(`Content-Type`, `text/plain; charset=UTF-8`)
+	fmt.Fprintf(w, "led.Low()")
+}
+
+func hello(w http.ResponseWriter, r *http.Request) {
+	w.Header().Set(`Content-Type`, `text/plain; charset=UTF-8`)
+	fmt.Fprintf(w, "hello")
+}
+
+var counter int
+
+func cnt(w http.ResponseWriter, r *http.Request) {
+	r.ParseForm()
+	if r.Method == "POST" {
+		c := r.Form.Get("cnt")
+		if c != "" {
+			i64, _ := strconv.ParseInt(c, 0, 0)
+			counter = int(i64)
+		}
+	}
+
+	w.Header().Set(`Content-Type`, `application/json`)
+	fmt.Fprintf(w, `{"cnt": %d}`, counter)
+}
+
+func message(msg string) {
+	println(msg, "\r")
+}

examples/rtl8720dn/webserver/wioterminal.go

@@ -0,0 +1,74 @@
+//go:build wioterminal
+// +build wioterminal
+
+package main
+
+import (
+	"device/sam"
+	"machine"
+	"runtime/interrupt"
+	"time"
+
+	"tinygo.org/x/drivers/rtl8720dn"
+)
+
+var (
+	uart UARTx
+)
+
+func handleInterrupt(interrupt.Interrupt) {
+	// should reset IRQ
+	uart.Receive(byte((uart.Bus.DATA.Get() & 0xFF)))
+	uart.Bus.INTFLAG.SetBits(sam.SERCOM_USART_INT_INTFLAG_RXC)
+}
+
+func setupRTL8720DN() (*rtl8720dn.RTL8720DN, error) {
+	machine.RTL8720D_CHIP_PU.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.RTL8720D_CHIP_PU.Low()
+	time.Sleep(100 * time.Millisecond)
+	machine.RTL8720D_CHIP_PU.High()
+	time.Sleep(1000 * time.Millisecond)
+	if debug {
+		waitSerial()
+	}
+
+	uart = UARTx{
+		UART: &machine.UART{
+			Buffer: machine.NewRingBuffer(),
+			Bus:    sam.SERCOM0_USART_INT,
+			SERCOM: 0,
+		},
+	}
+
+	uart.Interrupt = interrupt.New(sam.IRQ_SERCOM0_2, handleInterrupt)
+	uart.Configure(machine.UARTConfig{TX: machine.PB24, RX: machine.PC24, BaudRate: 614400})
+
+	rtl := rtl8720dn.New(uart)
+	rtl.Debug(debug)
+
+	_, err := rtl.Rpc_tcpip_adapter_init()
+	if err != nil {
+		return nil, err
+	}
+
+	return rtl, nil
+}
+
+// Wait for user to open serial console
+func waitSerial() {
+	for !machine.Serial.DTR() {
+		time.Sleep(100 * time.Millisecond)
+	}
+}
+
+type UARTx struct {
+	*machine.UART
+}
+
+func (u UARTx) Read(p []byte) (n int, err error) {
+	if u.Buffered() == 0 {
+		time.Sleep(1 * time.Millisecond)
+		return 0, nil
+	}
+	return u.UART.Read(p)
+}

examples/sdcard/console/feather-m4.go

@@ -1,3 +1,4 @@
+//go:build feather_m4 || feather_m4_can || feather_nrf52840
 // +build feather_m4 feather_m4_can feather_nrf52840
 
 package main

examples/sdcard/console/grandcentral-m4.go

@@ -1,4 +1,5 @@
-// +build grandcentral-m4
+//go:build grandcentral_m4
+// +build grandcentral_m4
 
 package main
 

examples/sdcard/console/m0.go

@@ -1,3 +1,4 @@
+//go:build atsamd21 && !p1am_100
 // +build atsamd21,!p1am_100
 
 package main

examples/sdcard/console/p1am-100.go

@@ -1,3 +1,4 @@
+//go:build p1am_100
 // +build p1am_100
 
 package main

examples/sdcard/console/pygamer.go

@@ -1,3 +1,4 @@
+//go:build pygamer
 // +build pygamer
 
 package main

examples/sdcard/console/pyportal.go

@@ -1,3 +1,4 @@
+//go:build pyportal
 // +build pyportal
 
 package main

examples/sdcard/console/wioterminal.go

@@ -1,3 +1,4 @@
+//go:build wioterminal
 // +build wioterminal
 
 package main

examples/sdcard/tinyfs/console/console.go

@@ -1,3 +1,4 @@
+//go:build tinygo
 // +build tinygo
 
 package console
@@ -11,7 +12,7 @@ import (
 	"strings"
 	"time"
 
-	"github.com/tinygo-org/tinyfs"
+	"tinygo.org/x/tinyfs"
 )
 
 const consoleBufLen = 64
@@ -35,6 +36,7 @@ var (
 	commands = map[string]cmdfunc{
 		"":        noop,
 		"dbg":     dbg,
+		"help":    help,
 		"lsblk":   lsblk,
 		"mount":   mount,
 		"umount":  umount,
@@ -160,6 +162,28 @@ func runCommand(line string) {
 
 func noop(argv []string) {}
 
+func help(argv []string) {
+	fmt.Printf("help\r\n")
+	fmt.Printf("  show help\r\n")
+	fmt.Printf("dbg\r\n")
+	fmt.Printf("  toggle debug mode\r\n")
+	fmt.Printf("xxd <hex address, ex: 0xA0> <size of hexdump in bytes>\r\n")
+	fmt.Printf("  hexdump the specified address\r\n")
+	fmt.Printf("ls <target file>\r\n")
+	fmt.Printf("  list information\r\n")
+	fmt.Printf("samples\r\n")
+	fmt.Printf("  write some files in the root directory\r\n")
+	fmt.Printf("mkdir <target dir>\r\n")
+	fmt.Printf("  create directory\r\n")
+	fmt.Printf("cat <target file>\r\n")
+	fmt.Printf("  print the contents of file\r\n")
+	fmt.Printf("create <target file>\r\n")
+	fmt.Printf("  create file\r\n")
+	fmt.Printf("write <target file>\r\n")
+	fmt.Printf("  write to file (press CTRL-D to exit)\r\n")
+	fmt.Printf("rm\r\n")
+}
+
 func dbg(argv []string) {
 	if debug {
 		debug = false
@@ -421,7 +445,7 @@ func cat(argv []string) {
 		println("Trying to cat to " + tgt)
 	}
 	if tgt == "" {
-		println("Usage: cat <target dir>")
+		println("Usage: cat <target file>")
 		return
 	}
 	if debug {

examples/sdcard/tinyfs/feather-m4.go

@@ -1,3 +1,4 @@
+//go:build feather_m4 || feather_m4_can || feather_nrf52840
 // +build feather_m4 feather_m4_can feather_nrf52840
 
 package main

examples/sdcard/tinyfs/grandcentral-m4.go

@@ -1,4 +1,5 @@
-// +build grandcentral-m4
+//go:build grandcentral_m4
+// +build grandcentral_m4
 
 package main
 

examples/sdcard/tinyfs/m0.go

@@ -1,3 +1,4 @@
+//go:build atsamd21 && !p1am_100
 // +build atsamd21,!p1am_100
 
 package main

examples/sdcard/tinyfs/main.go

@@ -5,9 +5,9 @@ import (
 	"machine"
 	"time"
 
-	"github.com/tinygo-org/tinyfs/fatfs"
 	"tinygo.org/x/drivers/examples/sdcard/tinyfs/console"
 	"tinygo.org/x/drivers/sdcard"
+	"tinygo.org/x/tinyfs/fatfs"
 )
 
 var (

examples/sdcard/tinyfs/p1am-100.go

@@ -1,3 +1,4 @@
+//go:build p1am_100
 // +build p1am_100
 
 package main

examples/sdcard/tinyfs/pygamer.go

@@ -1,3 +1,4 @@
+//go:build pygamer
 // +build pygamer
 
 package main

examples/sdcard/tinyfs/pyportal.go

@@ -1,3 +1,4 @@
+//go:build pyportal
 // +build pyportal
 
 package main

examples/sdcard/tinyfs/wioterminal.go

@@ -1,3 +1,4 @@
+//go:build wioterminal
 // +build wioterminal
 
 package main

examples/shtc3/main.go

@@ -0,0 +1,30 @@
+package main
+
+import (
+	"fmt"
+	"machine"
+	"time"
+
+	"tinygo.org/x/drivers/shtc3"
+)
+
+func main() {
+
+	machine.I2C0.Configure(machine.I2CConfig{})
+	sensor := shtc3.New(machine.I2C0)
+
+	for {
+
+		sensor.WakeUp()
+
+		temp, humidity, _ := sensor.ReadTemperatureHumidity()
+		t := fmt.Sprintf("%.2f", float32(temp)/1000)
+		h := fmt.Sprintf("%.2f", float32(humidity)/100)
+		println("Temperature:", t, "°C")
+		println("Humidity", h, "%")
+
+		sensor.Sleep()
+
+		time.Sleep(2 * time.Second)
+	}
+}

examples/sx126x/lora_continuous/lora_continuous.go

@@ -0,0 +1,80 @@
+package main
+
+// This example will periodically enable Continuous "Preamble" and "Wave" modes  on 868.1 Mhz
+import (
+	"machine"
+	"time"
+
+	rfswitch "tinygo.org/x/drivers/examples/sx126x/rfswitch"
+
+	"tinygo.org/x/drivers/sx126x"
+)
+
+const FREQ = 868100000
+
+var (
+	loraRadio *sx126x.Device
+)
+
+func main() {
+	println("\n# TinyGo Lora continuous Wave/Preamble test")
+	println("# -----------------------------------------")
+
+	machine.LED.Configure(machine.PinConfig{Mode: machine.PinOutput})
+
+	// Create the driver
+	loraRadio = sx126x.New(machine.SPI3)
+	loraRadio.SetDeviceType(sx126x.DEVICE_TYPE_SX1262)
+
+	// Create RF Switch
+	var radioSwitch rfswitch.CustomSwitch
+	loraRadio.SetRfSwitch(radioSwitch)
+
+	state := loraRadio.DetectDevice()
+	if !state {
+		panic("sx126x not detected. ")
+	}
+
+	// Prepare for Lora operation
+	loraConf := sx126x.LoraConfig{
+		Freq:           FREQ,
+		Bw:             sx126x.SX126X_LORA_BW_500_0,
+		Sf:             sx126x.SX126X_LORA_SF9,
+		Cr:             sx126x.SX126X_LORA_CR_4_7,
+		HeaderType:     sx126x.SX126X_LORA_HEADER_EXPLICIT,
+		Preamble:       12,
+		Ldr:            sx126x.SX126X_LORA_LOW_DATA_RATE_OPTIMIZE_OFF,
+		Iq:             sx126x.SX126X_LORA_IQ_STANDARD,
+		Crc:            sx126x.SX126X_LORA_CRC_ON,
+		SyncWord:       sx126x.SX126X_LORA_MAC_PRIVATE_SYNCWORD,
+		LoraTxPowerDBm: 14,
+	}
+	loraRadio.LoraConfig(loraConf)
+
+	// Although LoraConfig has already configured most of Lora settings,
+	// the following lines are still required to enable Continuous Preamble/Wave
+	loraRadio.SetPacketType(sx126x.SX126X_PACKET_TYPE_LORA)
+	loraRadio.SetRfFrequency(loraConf.Freq)
+	loraRadio.SetModulationParams(loraConf.Sf, loraConf.Bw, loraConf.Cr, loraConf.Ldr)
+	loraRadio.SetTxParams(loraConf.LoraTxPowerDBm, sx126x.SX126X_PA_RAMP_200U)
+
+	for {
+		println("2 seconds in Continuous Preamble")
+		loraRadio.SetStandby()
+		loraRadio.SetTxContinuousPreamble()
+		time.Sleep(2 * time.Second)
+		println("Continuous Preamble Stopped")
+
+		loraRadio.SetStandby()
+		time.Sleep(10 * time.Second)
+
+		println("2 seconds in Continuous Wave")
+		loraRadio.SetTxContinuousWave()
+		time.Sleep(2 * time.Second)
+		println(" Continuous Wave Stopped")
+
+		loraRadio.SetStandby()
+		time.Sleep(60 * time.Second)
+
+	}
+}

examples/sx126x/lora_rxtx/lora_rxtx.go

@@ -0,0 +1,98 @@
+package main
+
+// In this example, a Lora packet will be sent every 10s
+// module will be in RX mode between two transmissions
+
+import (
+	"device/stm32"
+	"machine"
+	"runtime/interrupt"
+	"time"
+
+	rfswitch "tinygo.org/x/drivers/examples/sx126x/rfswitch"
+
+	"tinygo.org/x/drivers/sx126x"
+)
+
+const FREQ = 868100000
+
+const (
+	LORA_DEFAULT_RXTIMEOUT_MS = 1000
+	LORA_DEFAULT_TXTIMEOUT_MS = 5000
+)
+
+var (
+	loraRadio *sx126x.Device
+	txmsg     = []byte("Hello TinyGO")
+)
+
+// radioIntHandler will take care of radio interrupts
+func radioIntHandler(intr interrupt.Interrupt) {
+	loraRadio.HandleInterrupt()
+}
+
+func main() {
+	println("\n# TinyGo Lora RX/TX test")
+	println("# ----------------------")
+	machine.LED.Configure(machine.PinConfig{Mode: machine.PinOutput})
+
+	// Create the driver
+	loraRadio = sx126x.New(machine.SPI3)
+	loraRadio.SetDeviceType(sx126x.DEVICE_TYPE_SX1262)
+
+	// Create RF Switch
+	var radioSwitch rfswitch.CustomSwitch
+	loraRadio.SetRfSwitch(radioSwitch)
+
+	// Detect the device
+	state := loraRadio.DetectDevice()
+	if !state {
+		panic("sx126x not detected.")
+	}
+
+	// Add interrupt handler for Radio IRQs
+	intr := interrupt.New(stm32.IRQ_Radio_IRQ_Busy, radioIntHandler)
+	intr.Enable()
+
+	loraConf := sx126x.LoraConfig{
+		Freq:           FREQ,
+		Bw:             sx126x.SX126X_LORA_BW_500_0,
+		Sf:             sx126x.SX126X_LORA_SF9,
+		Cr:             sx126x.SX126X_LORA_CR_4_7,
+		HeaderType:     sx126x.SX126X_LORA_HEADER_EXPLICIT,
+		Preamble:       12,
+		Ldr:            sx126x.SX126X_LORA_LOW_DATA_RATE_OPTIMIZE_OFF,
+		Iq:             sx126x.SX126X_LORA_IQ_STANDARD,
+		Crc:            sx126x.SX126X_LORA_CRC_ON,
+		SyncWord:       sx126x.SX126X_LORA_MAC_PRIVATE_SYNCWORD,
+		LoraTxPowerDBm: 20,
+	}
+
+	loraRadio.LoraConfig(loraConf)
+
+	var count uint
+	for {
+		tStart := time.Now()
+
+		// Blocking RX for LORA_DEFAULT_RXTIMEOUT_MS
+		println("Start Lora RX for 10 sec")
+		for int(time.Now().Sub(tStart).Seconds()) < 10 {
+			buf, err := loraRadio.LoraRx(LORA_DEFAULT_RXTIMEOUT_MS)
+
+			if err != nil {
+				println("RX Error: ", err)
+			} else if buf != nil {
+				println("Packet Received: len=", len(buf), string(buf))
+			}
+		}
+		println("END Lora RX")
+
+		println("LORA TX size=", len(txmsg))
+		err := loraRadio.LoraTx(txmsg, LORA_DEFAULT_TXTIMEOUT_MS)
+		if err != nil {
+			println("TX Error:", err)
+		}
+		count++
+	}
+
+}

examples/sx126x/rfswitch/gnse.go

@@ -0,0 +1,61 @@
+//go:build gnse
+// +build gnse
+
+/*
+ Generic Node Sensor Edition
+ RFSwitch
+
+ Disable Switch   :  PB8=OFF PA0=OFF  PA1=OFF
+ Enable RX        :  PB8=ON  PA0=ON   PA1=OFF
+ Enable TX RFO LP :  PB8=ON  PA0=ON   PA1=ON
+ Enable TX RFO HP :  PB8=ON  PA0=OFF  PA1=ON
+*/
+package rfswitch
+
+import (
+	"machine"
+
+	"tinygo.org/x/drivers/sx126x"
+)
+
+type CustomSwitch struct {
+}
+
+var (
+	rfstate int
+)
+
+func (s CustomSwitch) InitRFSwitch() {
+	machine.RF_FE_CTRL1.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.RF_FE_CTRL2.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.RF_FE_CTRL3.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	rfstate = -1 //Unknown
+}
+
+func (s CustomSwitch) SetRfSwitchMode(mode int) error {
+	if mode == rfstate {
+		return nil
+	}
+
+	switch mode {
+
+	case sx126x.RFSWITCH_TX_HP:
+		machine.RF_FE_CTRL1.Set(false)
+		machine.RF_FE_CTRL2.Set(true)
+		machine.RF_FE_CTRL3.Set(true)
+
+	case sx126x.RFSWITCH_TX_LP:
+		machine.RF_FE_CTRL1.Set(true)
+		machine.RF_FE_CTRL2.Set(true)
+		machine.RF_FE_CTRL3.Set(true)
+
+	case sx126x.RFSWITCH_RX:
+		machine.RF_FE_CTRL1.Set(true)
+		machine.RF_FE_CTRL2.Set(false)
+		machine.RF_FE_CTRL3.Set(true)
+	}
+
+	rfstate = mode
+
+	return nil
+}

examples/sx126x/rfswitch/lorae5.go

@@ -0,0 +1,43 @@
+//go:build lorae5
+// +build lorae5
+
+package radio
+
+/*
+/!\ LoRa-E5 module ONLY transmits through RFO_HP:
+
+	Receive: PA4=1, PA5=0
+	Transmit(high output power, SMPS mode): PA4=0, PA5=1
+
+*/
+
+import (
+	"errors"
+	"machine"
+
+	"tinygo.org/x/drivers/sx126x"
+)
+
+type CustomSwitch struct {
+}
+
+func (s CustomSwitch) InitRFSwitch() {
+	machine.PA4.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.PB5.Configure(machine.PinConfig{Mode: machine.PinOutput})
+}
+
+func (s CustomSwitch) SetRfSwitchMode(mode int) error {
+	switch mode {
+
+	case sx126x.RFSWITCH_RX:
+		machine.PA4.Set(true)
+		machine.PB5.Set(false)
+	case sx126x.RFSWITCH_TX_LP:
+		errors.New("RFSWITCH_TX_LP not supported ")
+	case sx126x.RFSWITCH_TX_HP:
+		machine.PA4.Set(false)
+		machine.PB5.Set(true)
+
+	}
+	return nil
+}

examples/sx126x/rfswitch/wl55jc.go

@@ -0,0 +1,55 @@
+//go:build nucleowl55jc
+// +build nucleowl55jc
+
+/*
+ Nucleo WL55JC1
+ RFSwitch
+
++-----------+---------+------------+------------+
+|           | FE_CTRL1 |  FE_CTRL2 |   FE_CTRL3 |
+|           |   (PC4)  |   (PC5)   |     (PC3)  |
++-----------+----------+-----------+------------+
+|  TX_HP    |   LOW    |   HIGH    |    HIGH    |
+|  TX_LP    |   HIGH   |   HIGH    |    HIGH    |
+|  RX       |   HIGH   |   LOW     |    HIGH    |
++-----------+----------+-----------+------------+
+*/
+package rfswitch
+
+import (
+	"machine"
+
+	"tinygo.org/x/drivers/sx126x"
+)
+
+type CustomSwitch struct {
+}
+
+func (s CustomSwitch) InitRFSwitch() {
+	machine.PC4.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.PC5.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	machine.PC3.Configure(machine.PinConfig{Mode: machine.PinOutput})
+}
+
+func (s CustomSwitch) SetRfSwitchMode(mode int) error {
+	switch mode {
+
+	case sx126x.RFSWITCH_TX_HP:
+		machine.PC4.Set(false)
+		machine.PC5.Set(true)
+		machine.PC3.Set(true)
+
+	case sx126x.RFSWITCH_TX_LP:
+		machine.PC4.Set(true)
+		machine.PC5.Set(true)
+		machine.PC3.Set(true)
+
+	case sx126x.RFSWITCH_RX:
+		machine.PC4.Set(true)
+		machine.PC5.Set(false)
+		machine.PC3.Set(true)
+
+	}
+	return nil
+
+}

examples/wifi/tcpclient/espat.go

@@ -0,0 +1,28 @@
+//go:build espat
+// +build espat
+
+package main
+
+import (
+	"machine"
+	"tinygo.org/x/drivers/espat"
+)
+
+// these are the default pins for the Arduino Nano33 IoT.
+// change these to connect to a different UART or pins for the ESP8266/ESP32
+var (
+	uart = machine.UART1
+	tx   = machine.PA22
+	rx   = machine.PA23
+
+	adaptor *espat.Device
+)
+
+func initAdaptor() *espat.Device {
+	uart.Configure(machine.UARTConfig{TX: tx, RX: rx})
+
+	adaptor = espat.New(uart)
+	adaptor.Configure()
+
+	return adaptor
+}