undo epd2in66b Configure method deletion

* si5351: add support for si5351

Adds support for the si5351 I2C programmable clock generator using code
from @chiefMarlin which used code from @conotto which somehow never got merged.

Thank you everyone!

Signed-off-by: deadprogram <ron@hybridgroup.com>

* refactor: use regmap instead of legacy package to avoid heap allocations

Signed-off-by: deadprogram <ron@hybridgroup.com>

---------

Signed-off-by: deadprogram <ron@hybridgroup.com>

apa102/apa102.go

@@ -5,9 +5,10 @@ package apa102 // import "tinygo.org/x/drivers/apa102"
 
 import (
 	"image/color"
-	"machine"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 const (
@@ -37,8 +38,11 @@ func New(b drivers.SPI) *Device {
 
 // NewSoftwareSPI returns a new APA102 driver that will use a software based
 // implementation of the SPI protocol.
-func NewSoftwareSPI(sckPin, sdoPin machine.Pin, delay uint32) *Device {
-	return New(&bbSPI{SCK: sckPin, SDO: sdoPin, Delay: delay})
+func NewSoftwareSPI(sckPin, sdoPin pin.Output, delay uint32) *Device {
+	return New(&bbSPI{SCK: sckPin.Set, SDO: sdoPin.Set, Delay: delay, configurePins: func() {
+		legacy.ConfigurePinOut(sckPin)
+		legacy.ConfigurePinOut(sdoPin)
+	}})
 }
 
 // WriteColors writes the given RGBA color slice out using the APA102 protocol.

apa102/softspi.go

@@ -1,6 +1,9 @@
 package apa102
 
-import "machine"
+import (
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
+)
 
 // bbSPI is a dumb bit-bang implementation of SPI protocol that is hardcoded
 // to mode 0 and ignores trying to receive data. Just enough for the APA102.
@@ -8,15 +11,18 @@ import "machine"
 // most purposes other than the APA102 package. It might be desirable to make
 // this more generic and include it in the TinyGo "machine" package instead.
 type bbSPI struct {
-	SCK   machine.Pin
-	SDO   machine.Pin
-	Delay uint32
+	SCK           pin.OutputFunc
+	SDO           pin.OutputFunc
+	Delay         uint32
+	configurePins func()
 }
 
 // Configure sets up the SCK and SDO pins as outputs and sets them low
 func (s *bbSPI) Configure() {
-	s.SCK.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	s.SDO.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	if s.configurePins == nil {
+		panic(legacy.ErrConfigBeforeInstantiated)
+	}
+	s.configurePins()
 	s.SCK.Low()
 	s.SDO.Low()
 	if s.Delay == 0 {

bmi160/bmi160.go

@@ -1,31 +1,36 @@
 package bmi160
 
 import (
-	"machine"
 	"time"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 // DeviceSPI is the SPI interface to a BMI160 accelerometer/gyroscope. There is
 // also an I2C interface, but it is not yet supported.
 type DeviceSPI struct {
 	// Chip select pin
-	CSB machine.Pin
+	csb pin.OutputFunc
 
 	buf [7]byte
 
 	// SPI bus (requires chip select to be usable).
-	Bus drivers.SPI
+	bus           drivers.SPI
+	configurePins func()
 }
 
 // NewSPI returns a new device driver. The pin and SPI interface are not
 // touched, provide a fully configured SPI object and call Configure to start
 // using this device.
-func NewSPI(csb machine.Pin, spi drivers.SPI) *DeviceSPI {
+func NewSPI(csb pin.Output, spi drivers.SPI) *DeviceSPI {
 	return &DeviceSPI{
-		CSB: csb, // chip select
-		Bus: spi,
+		csb: csb.Set, // chip select
+		bus: spi,
+		configurePins: func() {
+			legacy.ConfigurePinOut(csb)
+		},
 	}
 }
 
@@ -33,9 +38,11 @@ func NewSPI(csb machine.Pin, spi drivers.SPI) *DeviceSPI {
 // configures the BMI160, but it does not configure the SPI interface (it is
 // assumed to be up and running).
 func (d *DeviceSPI) Configure() error {
-	d.CSB.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.CSB.High()
-
+	if d.configurePins == nil {
+		return legacy.ErrConfigBeforeInstantiated
+	}
+	d.configurePins()
+	d.csb.High()
 	// The datasheet recommends doing a register read from address 0x7F to get
 	// SPI communication going:
 	// > If CSB sees a rising edge after power-up, the BMI160 interface switches
@@ -86,9 +93,9 @@ func (d *DeviceSPI) ReadTemperature() (temperature int32, err error) {
 	data[0] = 0x80 | reg_TEMPERATURE_0
 	data[1] = 0
 	data[2] = 0
-	d.CSB.Low()
-	err = d.Bus.Tx(data, data)
-	d.CSB.High()
+	d.csb.Low()
+	err = d.bus.Tx(data, data)
+	d.csb.High()
 	if err != nil {
 		return
 	}
@@ -123,9 +130,9 @@ func (d *DeviceSPI) ReadAcceleration() (x int32, y int32, z int32, err error) {
 	for i := 1; i < len(data); i++ {
 		data[i] = 0
 	}
-	d.CSB.Low()
-	err = d.Bus.Tx(data, data)
-	d.CSB.High()
+	d.csb.Low()
+	err = d.bus.Tx(data, data)
+	d.csb.High()
 	if err != nil {
 		return
 	}
@@ -153,9 +160,9 @@ func (d *DeviceSPI) ReadRotation() (x int32, y int32, z int32, err error) {
 	for i := 1; i < len(data); i++ {
 		data[i] = 0
 	}
-	d.CSB.Low()
-	err = d.Bus.Tx(data, data)
-	d.CSB.High()
+	d.csb.Low()
+	err = d.bus.Tx(data, data)
+	d.csb.High()
 	if err != nil {
 		return
 	}
@@ -201,9 +208,9 @@ func (d *DeviceSPI) readRegister(address uint8) uint8 {
 	data := d.buf[:2]
 	data[0] = 0x80 | address
 	data[1] = 0
-	d.CSB.Low()
-	d.Bus.Tx(data, data)
-	d.CSB.High()
+	d.csb.Low()
+	d.bus.Tx(data, data)
+	d.csb.High()
 	return data[1]
 }
 
@@ -217,7 +224,7 @@ func (d *DeviceSPI) writeRegister(address, data uint8) {
 	buf[0] = address
 	buf[1] = data
 
-	d.CSB.Low()
-	d.Bus.Tx(buf, buf)
-	d.CSB.High()
+	d.csb.Low()
+	d.bus.Tx(buf, buf)
+	d.csb.High()
 }

buzzer/buzzer.go

@@ -2,22 +2,22 @@
 package buzzer // import "tinygo.org/x/drivers/buzzer"
 
 import (
-	"machine"
-
 	"time"
+
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 // Device wraps a GPIO connection to a buzzer.
 type Device struct {
-	pin  machine.Pin
+	pin  pin.OutputFunc
 	High bool
 	BPM  float64
 }
 
 // New returns a new buzzer driver given which pin to use
-func New(pin machine.Pin) Device {
+func New(pin pin.Output) Device {
 	return Device{
-		pin:  pin,
+		pin:  pin.Set,
 		High: false,
 		BPM:  96.0,
 	}
@@ -25,14 +25,14 @@ func New(pin machine.Pin) Device {
 
 // On sets the buzzer to a high state.
 func (l *Device) On() (err error) {
-	l.pin.Set(true)
+	l.pin.High()
 	l.High = true
 	return
 }
 
 // Off sets the buzzer to a low state.
 func (l *Device) Off() (err error) {
-	l.pin.Set(false)
+	l.pin.Low()
 	l.High = false
 	return
 }

easystepper/easystepper.go

@@ -2,9 +2,9 @@
 package easystepper // import "tinygo.org/x/drivers/easystepper"
 
 import (
-	"errors"
-	"machine"
 	"time"
+
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 // StepMode determines the coil sequence used to perform a single step
@@ -30,28 +30,10 @@ func (sm StepMode) stepCount() uint {
 	}
 }
 
-// DeviceConfig contains the configuration data for a single easystepper driver
-type DeviceConfig struct {
-	// Pin1 ... Pin4 determines the pins to configure and use for the device
-	Pin1, Pin2, Pin3, Pin4 machine.Pin
-	// StepCount is the number of steps required to perform a full revolution of the stepper motor
-	StepCount uint
-	// RPM determines the speed of the stepper motor in 'Revolutions per Minute'
-	RPM uint
-	// Mode determines the coil sequence used to perform a single step
-	Mode StepMode
-}
-
-// DualDeviceConfig contains the configuration data for a dual easystepper driver
-type DualDeviceConfig struct {
-	DeviceConfig
-	// Pin5 ... Pin8 determines the pins to configure and use for the second device
-	Pin5, Pin6, Pin7, Pin8 machine.Pin
-}
-
 // Device holds the pins and the delay between steps
 type Device struct {
-	pins       [4]machine.Pin
+	pins       [4]pin.OutputFunc
+	config     func()
 	stepDelay  time.Duration
 	stepNumber uint8
 	stepMode   StepMode
@@ -62,51 +44,6 @@ type DualDevice struct {
 	devices [2]*Device
 }
 
-// New returns a new single easystepper driver given a DeviceConfig
-func New(config DeviceConfig) (*Device, error) {
-	if config.StepCount == 0 || config.RPM == 0 {
-		return nil, errors.New("config.StepCount and config.RPM must be > 0")
-	}
-	return &Device{
-		pins:      [4]machine.Pin{config.Pin1, config.Pin2, config.Pin3, config.Pin4},
-		stepDelay: time.Second * 60 / time.Duration((config.StepCount * config.RPM)),
-		stepMode:  config.Mode,
-	}, nil
-}
-
-// Configure configures the pins of the Device
-func (d *Device) Configure() {
-	for _, pin := range d.pins {
-		pin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	}
-}
-
-// NewDual returns a new dual easystepper driver given 8 pins, number of steps and rpm
-func NewDual(config DualDeviceConfig) (*DualDevice, error) {
-	// Create the first device
-	dev1, err := New(config.DeviceConfig)
-	if err != nil {
-		return nil, err
-	}
-	// Create the second device
-	config.DeviceConfig.Pin1 = config.Pin5
-	config.DeviceConfig.Pin2 = config.Pin6
-	config.DeviceConfig.Pin3 = config.Pin7
-	config.DeviceConfig.Pin4 = config.Pin8
-	dev2, err := New(config.DeviceConfig)
-	if err != nil {
-		return nil, err
-	}
-	// Return composite dual device
-	return &DualDevice{devices: [2]*Device{dev1, dev2}}, nil
-}
-
-// Configure configures the pins of the DualDevice
-func (d *DualDevice) Configure() {
-	d.devices[0].Configure()
-	d.devices[1].Configure()
-}
-
 // Move rotates the motor the number of given steps
 // (negative steps will rotate it the opposite direction)
 func (d *Device) Move(steps int32) {

easystepper/easystepper_go.go

@@ -0,0 +1,26 @@
+package easystepper
+
+import (
+	"errors"
+	"time"
+
+	"tinygo.org/x/drivers/internal/pin"
+)
+
+func NewCrossPlatform(stepcount, rpm uint, mode StepMode, pins [4]pin.OutputFunc) (*Device, error) {
+	if stepcount == 0 || rpm == 0 {
+		return nil, errors.New("zero rpm and/or stepcount")
+	}
+	for i := range pins {
+		if pins[i] == nil {
+			return nil, errors.New("nil pin")
+		}
+	}
+	d := &Device{
+		pins:      pins,
+		stepDelay: time.Second * 60 / time.Duration((stepcount * rpm)),
+		stepMode:  mode,
+		config:    func() {},
+	}
+	return d, nil
+}

easystepper/easystepper_tinygo.go

@@ -0,0 +1,83 @@
+//go:build baremetal
+
+package easystepper
+
+import (
+	"errors"
+	"machine"
+	"time"
+
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
+)
+
+// New returns a new single easystepper driver given a DeviceConfig
+func New(config DeviceConfig) (*Device, error) {
+	if config.StepCount == 0 || config.RPM == 0 {
+		return nil, errors.New("config.StepCount and config.RPM must be > 0")
+	}
+	return &Device{
+		pins:      [4]pin.OutputFunc{config.Pin1.Set, config.Pin2.Set, config.Pin3.Set, config.Pin4.Set},
+		stepDelay: time.Second * 60 / time.Duration((config.StepCount * config.RPM)),
+		stepMode:  config.Mode,
+		config: func() {
+			legacy.ConfigurePinOut(config.Pin1)
+			legacy.ConfigurePinOut(config.Pin2)
+			legacy.ConfigurePinOut(config.Pin3)
+			legacy.ConfigurePinOut(config.Pin4)
+		},
+	}, nil
+}
+
+// Configure configures the pins of the Device
+func (d *Device) Configure() {
+	if d.config == nil {
+		panic(legacy.ErrConfigBeforeInstantiated)
+	}
+	d.config()
+}
+
+// Configure configures the pins of the DualDevice
+func (d *DualDevice) Configure() {
+	d.devices[0].Configure()
+	d.devices[1].Configure()
+}
+
+// NewDual returns a new dual easystepper driver given 8 pins, number of steps and rpm
+func NewDual(config DualDeviceConfig) (*DualDevice, error) {
+	// Create the first device
+	dev1, err := New(config.DeviceConfig)
+	if err != nil {
+		return nil, err
+	}
+	// Create the second device
+	config.DeviceConfig.Pin1 = config.Pin5
+	config.DeviceConfig.Pin2 = config.Pin6
+	config.DeviceConfig.Pin3 = config.Pin7
+	config.DeviceConfig.Pin4 = config.Pin8
+	dev2, err := New(config.DeviceConfig)
+	if err != nil {
+		return nil, err
+	}
+	// Return composite dual device
+	return &DualDevice{devices: [2]*Device{dev1, dev2}}, nil
+}
+
+// DeviceConfig contains the configuration data for a single easystepper driver
+type DeviceConfig struct {
+	// Pin1 ... Pin4 determines the pins to configure and use for the device
+	Pin1, Pin2, Pin3, Pin4 machine.Pin
+	// StepCount is the number of steps required to perform a full revolution of the stepper motor
+	StepCount uint
+	// RPM determines the speed of the stepper motor in 'Revolutions per Minute'
+	RPM uint
+	// Mode determines the coil sequence used to perform a single step
+	Mode StepMode
+}
+
+// DualDeviceConfig contains the configuration data for a dual easystepper driver
+type DualDeviceConfig struct {
+	DeviceConfig
+	// Pin5 ... Pin8 determines the pins to configure and use for the second device
+	Pin5, Pin6, Pin7, Pin8 machine.Pin
+}

encoders/quadrature_interrupt.go

@@ -1,4 +1,4 @@
-//go:build tinygo && (rp2040 || stm32 || k210 || esp32c3 || nrf || sam || (avr && (atmega328p || atmega328pb)))
+//go:build tinygo && (rp2040 || rp2350 || stm32 || k210 || esp32c3 || nrf || sam || (avr && (atmega328p || atmega328pb)))
 
 // Implementation based on:
 // https://gist.github.com/aykevl/3fc1683ed77bb0a9c07559dfe857304a

examples/honeyhsc/example.go

@@ -0,0 +1,49 @@
+package main
+
+import (
+	"machine"
+	"time"
+
+	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/honeyhsc"
+)
+
+// Data taken from https://github.com/rodan/honeywell_hsc_ssc_i2c/blob/master/hsc_ssc_i2c.cpp
+// these defaults are valid for the HSCMRNN030PA2A3 chip
+const (
+	i2cAddress = 0x28
+	// 10%
+	outputMinimum = 0x666
+	// 90% of 2^14 - 1
+	outputMax = 0x399A
+	// min is 0 for sensors that give absolute values
+	pressureMin = 0
+	// 30psi (and we want results in millipascals)
+	// pressureMax = 206842.7
+	pressureMax = 206843 * 1000
+)
+
+func main() {
+	bus := machine.I2C0
+	err := bus.Configure(machine.I2CConfig{
+		Frequency: 400_000, // 100kHz minimum and 400kHz I2C maximum clock. 50 to 800 for SPI.
+		SDA:       machine.I2C0_SDA_PIN,
+		SCL:       machine.I2C0_SCL_PIN,
+	})
+	if err != nil {
+		panic(err.Error())
+	}
+	sensor := honeyhsc.NewDevI2C(bus, i2cAddress, outputMinimum, outputMax, pressureMin, pressureMax)
+	for {
+		time.Sleep(time.Second)
+		const measuremask = drivers.Pressure | drivers.Temperature
+		err := sensor.Update(measuremask)
+		if err != nil {
+			println("error updating measurements:", err.Error())
+			continue
+		}
+		P := sensor.Pressure()
+		T := sensor.Temperature()
+		println("pressure:", P, "temperature:", T)
+	}
+}

examples/lis3dh/main.go

@@ -14,9 +14,18 @@ func main() {
 	i2c.Configure(machine.I2CConfig{SCL: machine.SCL1_PIN, SDA: machine.SDA1_PIN})
 
 	accel := lis3dh.New(i2c)
-	accel.Address = lis3dh.Address1 // address on the Circuit Playground Express
-	accel.Configure()
-	accel.SetRange(lis3dh.RANGE_2_G)
+	err := accel.Configure(lis3dh.Config{
+		Address: lis3dh.Address1, // address on the Circuit Playground Express
+	})
+	for err != nil {
+		println("could not configure LIS3DH:", err)
+		time.Sleep(time.Second)
+	}
+	err = accel.SetRange(lis3dh.RANGE_2_G)
+	for err != nil {
+		println("could not set acceleration range:", err)
+		time.Sleep(time.Second)
+	}
 
 	println(accel.Connected())
 

examples/si5351/main.go

@@ -0,0 +1,107 @@
+package main
+
+import (
+	"machine"
+	"time"
+
+	"tinygo.org/x/drivers/si5351"
+)
+
+// Simple demo of the SI5351 clock generator.
+// This is like the Arduino library example:
+//   https://github.com/adafruit/Adafruit_Si5351_Library/blob/master/examples/si5351/si5351.ino
+// Which will configure the chip with:
+//  - PLL A at 900mhz
+//  - PLL B at 616.66667mhz
+//  - Clock 0 at 112.5mhz, using PLL A as a source divided by 8
+//  - Clock 1 at 13.5531mhz, using PLL B as a source divided by 45.5
+//  - Clock 2 at 10.76khz, using PLL B as a source divided by 900 and further divided with an R divider of 64.
+
+func main() {
+	time.Sleep(5 * time.Second)
+
+	println("Si5351 Clockgen Test")
+	println()
+
+	// Configure I2C bus
+	machine.I2C0.Configure(machine.I2CConfig{})
+
+	// Create driver instance
+	clockgen := si5351.New(machine.I2C0)
+
+	// Verify device wired properly
+	connected, err := clockgen.Connected()
+	if err != nil {
+		println("Unable to read device status")
+		time.Sleep(time.Second)
+	}
+	if !connected {
+		for {
+			println("Unable to detect si5351 device")
+			time.Sleep(time.Second)
+		}
+	}
+
+	// Initialise device
+	clockgen.Configure()
+
+	// Now configue the PLLs and clock outputs.
+	// The PLLs can be configured with a multiplier and division of the on-board
+	// 25mhz reference crystal.  For example configure PLL A to 900mhz by multiplying
+	// by 36.  This uses an integer multiplier which is more accurate over time
+	// but allows less of a range of frequencies compared to a fractional
+	// multiplier shown next.
+	clockgen.ConfigurePLL(si5351.PLL_A, 36, 0, 1) // Multiply 25mhz by 36
+	println("PLL A frequency: 900mhz")
+
+	// And next configure PLL B to 616.6667mhz by multiplying 25mhz by 24.667 using
+	// the fractional multiplier configuration.  Notice you specify the integer
+	// multiplier and then a numerator and denominator as separate values, i.e.
+	// numerator 2 and denominator 3 means 2/3 or 0.667.  This fractional
+	// configuration is susceptible to some jitter over time but can set a larger
+	// range of frequencies.
+	clockgen.ConfigurePLL(si5351.PLL_B, 24, 2, 3) // Multiply 25mhz by 24.667 (24 2/3)
+	println("PLL B frequency: 616.6667mhz")
+
+	// Now configure the clock outputs.  Each is driven by a PLL frequency as input
+	// and then further divides that down to a specific frequency.
+	// Configure clock 0 output to be driven by PLL A divided by 8, so an output
+	// of 112.5mhz (900mhz / 8).  Again this uses the most precise integer division
+	// but can't set as wide a range of values.
+	clockgen.ConfigureMultisynth(0, si5351.PLL_A, 8, 0, 1) // Divide by 8 (8 0/1)
+	println("Clock 0: 112.5mhz")
+
+	// Next configure clock 1 to be driven by PLL B divided by 45.5 to get
+	// 13.5531mhz (616.6667mhz / 45.5).  This uses fractional division and again
+	// notice the numerator and denominator are explicitly specified.  This is less
+	// precise but allows a large range of frequencies.
+	clockgen.ConfigureMultisynth(1, si5351.PLL_B, 45, 1, 2) // Divide by 45.5 (45 1/2)
+	println("Clock 1: 13.5531mhz")
+
+	// Finally configure clock 2 to be driven by PLL B divided once by 900 to get
+	// down to 685.15 khz and then further divided by a special R divider that
+	// divides 685.15 khz by 64 to get a final output of 10.706khz.
+	clockgen.ConfigureMultisynth(2, si5351.PLL_B, 900, 0, 1) // Divide by 900 (900 0/1)
+	// Set the R divider, this can be a value of:
+	//  - R_DIV_1: divider of 1
+	//  - R_DIV_2: divider of 2
+	//  - R_DIV_4: divider of 4
+	//  - R_DIV_8: divider of 8
+	//  - R_DIV_16: divider of 16
+	//  - R_DIV_32: divider of 32
+	//  - R_DIV_64: divider of 64
+	//  - R_DIV_128: divider of 128
+	clockgen.ConfigureRdiv(2, si5351.R_DIV_64)
+	println("Clock 2: 10.706khz")
+
+	// After configuring PLLs and clocks, enable the outputs.
+	clockgen.EnableOutputs()
+
+	for {
+		time.Sleep(5 * time.Second)
+		println()
+		println("Clock 0: 112.5mhz")
+		println("Clock 1: 13.5531mhz")
+		println("Clock 2: 10.706khz")
+	}
+}

flash/devices.go

@@ -46,6 +46,10 @@ var DefaultDeviceIdentifier = DeviceIdentifierFunc(func(id JedecID) Attrs {
 		return GD25Q16C()
 	case 0xC84017:
 		return GD25Q64C()
+	case 0x856015:
+		return P25Q16H()
+	case 0xEF4014:
+		return W25Q80DV()
 	case 0xEF4015:
 		return W25Q16JVIQ()
 	case 0xEF4016:
@@ -239,6 +243,24 @@ func GD25Q64C() Attrs {
 	}
 }
 
+// Settings for the Puya P25Q16H 2MiB SPI flash.
+// Datasheet: https://files.seeedstudio.com/wiki/github_weiruanexample/Flash_P25Q16H-UXH-IR_Datasheet.pdf
+func P25Q16H() Attrs {
+	return Attrs{
+		TotalSize:           1 << 21, // 2 MiB
+		StartUp:             5000 * time.Microsecond,
+		JedecID:             JedecID{0x85, 0x60, 0x15},
+		MaxClockSpeedMHz:    55,
+		QuadEnableBitMask:   0x02,
+		HasSectorProtection: true,
+		SupportsFastRead:    true,
+		SupportsQSPI:        true,
+		SupportsQSPIWrites:  true,
+		WriteStatusSplit:    true,
+		SingleStatusByte:    false,
+	}
+}
+
 // Settings for the Winbond W25Q16JV-IQ 2MiB SPI flash. Note that JV-IM has a
 // different .memory_type (0x70) Datasheet:
 // https://www.winbond.com/resource-files/w25q16jv%20spi%20revf%2005092017.pdf
@@ -380,6 +402,25 @@ func W25Q80DL() Attrs {
 		TotalSize:           1 << 20, // 1 MiB
 		StartUp:             5000 * time.Microsecond,
 		JedecID:             JedecID{0xEF, 0x60, 0x14},
+		MaxClockSpeedMHz:    80,
+		QuadEnableBitMask:   0x02,
+		HasSectorProtection: false,
+		SupportsFastRead:    true,
+		SupportsQSPI:        true,
+		SupportsQSPIWrites:  false,
+		WriteStatusSplit:    false,
+		SingleStatusByte:    false,
+	}
+}
+
+// Settings for the Winbond W25Q80DV 2MiB SPI flash.
+// Datasheet:
+// https://www.winbond.com/resource-files/w25q80dv%20dl_revh_10022015.pdf
+func W25Q80DV() Attrs {
+	return Attrs{
+		TotalSize:           1 << 21, // 2 MiB
+		StartUp:             5000 * time.Microsecond,
+		JedecID:             JedecID{0xEF, 0x40, 0x14},
 		MaxClockSpeedMHz:    104,
 		QuadEnableBitMask:   0x02,
 		HasSectorProtection: false,

ft6336/ft6336.go

@@ -1,3 +1,6 @@
+// Guarded because still unsure of how to deal with interrupt drivers.
+//go:build tinygo
+
 // Package ft6336 provides a driver for the FT6336 I2C Self-Capacitive touch
 // panel controller.
 //

gc9a01/gc9a01.go

@@ -5,12 +5,13 @@ package gc9a01 // import "tinygo.org/x/drivers/gc9a01"
 
 import (
 	"image/color"
-	"machine"
 	"time"
 
 	"errors"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 // Rotation controls the rotation used by the display.
@@ -22,10 +23,10 @@ type FrameRate uint8
 // Device wraps an SPI connection.
 type Device struct {
 	bus             drivers.SPI
-	dcPin           machine.Pin
-	resetPin        machine.Pin
-	csPin           machine.Pin
-	blPin           machine.Pin
+	dcPin           pin.OutputFunc
+	resetPin        pin.OutputFunc
+	csPin           pin.OutputFunc
+	blPin           pin.OutputFunc
 	width           int16
 	height          int16
 	columnOffsetCfg int16
@@ -52,17 +53,17 @@ type Config struct {
 }
 
 // New creates a new ST7789 connection. The SPI wire must already be configured.
-func New(bus drivers.SPI, resetPin, dcPin, csPin, blPin machine.Pin) Device {
-	resetPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	dcPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	csPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	blPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
+func New(bus drivers.SPI, resetPin, dcPin, csPin, blPin pin.Output) Device {
+	legacy.ConfigurePinOut(resetPin)
+	legacy.ConfigurePinOut(dcPin)
+	legacy.ConfigurePinOut(csPin)
+	legacy.ConfigurePinOut(blPin)
 	return Device{
 		bus:      bus,
-		resetPin: resetPin,
-		dcPin:    dcPin,
-		csPin:    csPin,
-		blPin:    blPin,
+		resetPin: resetPin.Set,
+		dcPin:    dcPin.Set,
+		csPin:    csPin.Set,
+		blPin:    blPin.Set,
 	}
 }
 
@@ -226,7 +227,7 @@ func (d *Device) Data(data uint8) {
 
 // Tx sends data to the display
 func (d *Device) Tx(data []byte, isCommand bool) {
-	d.dcPin.Set(!isCommand)
+	d.dcPin(!isCommand)
 	d.bus.Tx(data, nil)
 }
 

hcsr04/hcsr04.go

@@ -5,30 +5,39 @@
 package hcsr04
 
 import (
-	"machine"
 	"time"
+
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 const TIMEOUT = 23324 // max sensing distance (4m)
 
 // Device holds the pins
 type Device struct {
-	trigger machine.Pin
-	echo    machine.Pin
+	trigger       pin.OutputFunc
+	echo          pin.InputFunc
+	configurePins func()
 }
 
 // New returns a new ultrasonic driver given 2 pins
-func New(trigger, echo machine.Pin) Device {
+func New(trigger pin.Output, echo pin.Input) Device {
 	return Device{
-		trigger: trigger,
-		echo:    echo,
+		trigger: trigger.Set,
+		echo:    echo.Get,
+		configurePins: func() {
+			legacy.ConfigurePinOut(trigger)
+			legacy.ConfigurePinInput(echo)
+		},
 	}
 }
 
 // Configure configures the pins of the Device
 func (d *Device) Configure() {
-	d.trigger.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.echo.Configure(machine.PinConfig{Mode: machine.PinInput})
+	if d.configurePins == nil {
+		panic(legacy.ErrConfigBeforeInstantiated)
+	}
+	d.configurePins()
 }
 
 // ReadDistance returns the distance of the object in mm
@@ -52,7 +61,7 @@ func (d *Device) ReadPulse() int32 {
 	d.trigger.Low()
 	i := uint8(0)
 	for {
-		if d.echo.Get() {
+		if d.echo() {
 			t = time.Now()
 			break
 		}
@@ -66,7 +75,7 @@ func (d *Device) ReadPulse() int32 {
 	}
 	i = 0
 	for {
-		if !d.echo.Get() {
+		if !d.echo() {
 			return int32(time.Since(t).Microseconds())
 		}
 		i++

hd44780/hd44780.go

@@ -210,7 +210,7 @@ func (d *Device) SendCommand(command byte) {
 	d.bus.SetCommandMode(true)
 	d.bus.Write([]byte{command})
 
-	for d.busy(command == DISPLAY_CLEAR || command == CURSOR_HOME) {
+	for d.isBusy(command == DISPLAY_CLEAR || command == CURSOR_HOME) {
 	}
 }
 
@@ -219,7 +219,7 @@ func (d *Device) sendData(data byte) {
 	d.bus.SetCommandMode(false)
 	d.bus.Write([]byte{data})
 
-	for d.busy(false) {
+	for d.isBusy(false) {
 	}
 }
 
@@ -231,9 +231,9 @@ func (d *Device) CreateCharacter(cgramAddr uint8, data []byte) {
 	}
 }
 
-// busy returns true when hd447890 is busy
+// isBusy returns true when hd447890 is isBusy
 // or after the timeout specified
-func (d *Device) busy(longDelay bool) bool {
+func (d *Device) isBusy(longDelay bool) bool {
 	if d.bus.WriteOnly() {
 		// Can't read busy flag if write only, so sleep a bit then return
 		if longDelay {
@@ -261,7 +261,7 @@ func (d *Device) busy(longDelay bool) bool {
 
 // Busy returns true when hd447890 is busy
 func (d *Device) Busy() bool {
-	return d.busy(false)
+	return d.isBusy(false)
 }
 
 // Size returns the current size of the display.

honeyhsc/hsc.go

@@ -0,0 +1,191 @@
+package honeyhsc
+
+import (
+	"errors"
+	"math"
+
+	"tinygo.org/x/drivers"
+)
+
+var (
+	errSensorMissing = errors.New("hsc: not connected")
+	errDiagnostic    = errors.New("hsc: diagnostic error")
+)
+
+const (
+	measuremask  = drivers.Pressure | drivers.Temperature
+	statusMask   = 0b1100_0000
+	statusOffset = 6
+)
+
+// DevI2C is the TruStability® High Accuracy Silicon Ceramic (HSC) Series is a piezoresistive silicon pressure sensor offering a ratiometric
+// analog or digital output for reading pressure over the specified full scale pressure span and temperature range.
+type DevI2C struct {
+	bus drivers.I2C
+	dev
+	addr uint8
+	buf  [6]byte
+}
+
+// NewDevI2C creates and returns a new DevI2C that communicates with an HSC device over the provided I2C bus.
+// Parameters:
+//   - bus: the I2C bus to use.
+//   - addr: the 7-bit I2C address of the sensor.
+//   - outMin, outMax: raw output code range (counts) corresponding to the pressure span. Depends on sensor model.
+//   - pMin, pMax: pressure range endpoints in millipascals (mPa). Depends on sensor model.
+//
+// The returned DevI2C will use these calibration parameters to convert raw bridge counts to pressure.
+func NewDevI2C(bus drivers.I2C, addr, outMin, outMax uint16, pMin, pMax int32) *DevI2C {
+	h := &DevI2C{
+		bus:  bus,
+		addr: uint8(addr),
+		dev: dev{
+			cmin: outMin,
+			cmax: outMax,
+			pmin: pMin,
+			pmax: pMax,
+		},
+	}
+	return h
+}
+
+// ReadTemperature reads and returns the temperature in milliKelvin (mC) from the I2C-attached HSC device.
+// It performs an Update internally to get the latest temperature value.
+func (h *DevI2C) ReadTemperature() (int32, error) {
+	err := h.Update(drivers.Temperature)
+	if err != nil {
+		return 0, err
+	}
+	return h.Temperature(), nil
+}
+
+// Update reads both temperature and pressure data from the I2C-attached HSC device when
+// the requested measurement mask includes pressure or temperature.
+// If neither pressure nor temperature is requested, Update is a no-op.
+func (d *DevI2C) Update(which drivers.Measurement) error {
+	// Update performs an I2C transaction to read 4 bytes, parses the status bits, 14-bit bridge data and
+	// temperature bits, and forwards them to the internal update routine. Any I2C transport error is returned,
+	// as well as errors produced by the internal update (e.g. errSensorMissing, errDiagnostic).
+	if which&measuremask == 0 {
+		return nil
+	}
+	rbuf := d.buf[:4]
+	wbuf := d.buf[4:6]
+	const reg = 0
+	value := (d.addr << 1) | 1
+	wbuf[0] = reg
+	wbuf[1] = value
+	err := d.bus.Tx(uint16(d.addr), wbuf, rbuf)
+	if err != nil {
+		return err
+	}
+	status := (rbuf[0] & statusMask) >> statusOffset
+	bridgeData := (uint16(rbuf[0]&^statusMask) << 8) | uint16(rbuf[1])
+	tempData := uint16(rbuf[2])<<8 | uint16(rbuf[3]&0xe0)>>5
+	return d.dev.update(status, bridgeData, tempData)
+}
+
+type pinout func(level bool)
+
+// DevI2C is the TruStability® High Accuracy Silicon Ceramic (HSC) Series is a piezoresistive silicon pressure sensor offering a ratiometric
+// analog or digital output for reading pressure over the specified full scale pressure span and temperature range.
+type DevSPI struct {
+	spi drivers.SPI
+	cs  pinout
+	dev
+	buf [4]byte
+}
+
+// NewDevSPI creates and returns a new DevSPI that communicates with an HSC device over SPI.
+// Parameters:
+//   - conn: the SPI connection to use.
+//   - cs: a chip-select function that drives the device select line low/high.
+//   - outMin, outMax: raw output code range (counts) corresponding to the pressure span. Depends on sensor model.
+//   - pMin, pMax: pressure range endpoints in millipascals (mPa). Depends on sensor model.
+//
+// The function returns the constructed DevSPI and an error value (currently always nil).
+func NewDevSPI(conn drivers.SPI, cs pinout, outMin, outMax uint16, pMin, pMax int32) (*DevSPI, error) {
+	h := &DevSPI{
+		spi: conn,
+		cs:  cs,
+		dev: dev{
+			cmin: outMin,
+			cmax: outMax,
+			pmin: pMin,
+			pmax: pMax,
+		},
+	}
+	return h, nil
+}
+
+// ReadTemperature reads and returns the temperature in milliKelvin (mC) from the SPI-attached HSC device.
+// It performs an Update internally to get the latest temperature value.
+func (h *DevSPI) ReadTemperature() (int32, error) {
+	err := h.Update(drivers.Temperature)
+	if err != nil {
+		return 0, err
+	}
+	return h.Temperature(), nil
+}
+
+// Update reads pressure and temperature data from the SPI-attached HSC device when the requested measurement mask includes
+// pressure or temperature. If neither pressure nor temperature is requested, Update is a no-op.
+func (h *DevSPI) Update(which drivers.Measurement) error {
+	// It toggles the provided chip-select, performs an SPI transfer to read 4 bytes, parses the status bits,
+	// 14-bit bridge data and temperature bits, and forwards them to the internal update routine. Any SPI
+	// transport error is returned, as well as errors produced by the internal update (e.g. errSensorMissing, errDiagnostic).
+	if which&measuremask == 0 {
+		return nil
+	}
+	buf := &h.buf
+	h.cs(false)
+	err := h.spi.Tx(nil, buf[:4])
+	h.cs(true)
+	if err != nil {
+		return err
+	}
+	// First two bits are status bits.
+	status := (buf[0] & statusMask) >> statusOffset
+	bridgeData := (uint16(buf[0]&^statusMask) << 8) | uint16(buf[1])
+
+	tempData := uint16(buf[2])<<8 | uint16(buf[3]&0xe0)>>5
+	return h.dev.update(status, bridgeData, tempData)
+}
+
+type dev struct {
+	pressure   int32
+	temp       int32
+	cmin, cmax uint16
+	pmin, pmax int32
+}
+
+// Pressure returns the most recently computed pressure value in millipascals (mPa).
+// The value is taken from the last successful Update.
+func (d *dev) Pressure() int32 {
+	return d.pressure
+}
+
+// Temperature returns the most recently read temperature value in milliKelvin (mC).
+// The value is taken from the last successful Update.
+func (d *dev) Temperature() int32 {
+	return d.temp + 273_150
+}
+
+// update interprets raw sensor fields (status, bridgeData, tempData) and updates the dev's stored
+// pressure and temperature. It returns errSensorMissing when the temperature raw value indicates no sensor
+// (tempData == math.MaxUint16), errDiagnostic when the status indicates a device diagnostic condition
+// (status == 3), or nil on success. Pressure is computed with integer arithmetic using the configured
+// cmin/cmax -> pmin/pmax linear mapping in order to avoid overflows.
+func (d *dev) update(status uint8, bridgeData, tempData uint16) error {
+	if tempData == math.MaxUint16 {
+		return errSensorMissing
+	} else if status == 3 {
+		return errDiagnostic
+	}
+
+	// Take care not to overflow here.
+	p := (int32(bridgeData)-int32(d.cmin))*(d.pmax-d.pmin)/int32(d.cmax-d.cmin) + d.pmin
+	d.temp = int32(tempData)
+	d.pressure = p
+	return nil
+}

internal/legacy/pinconfig.go

@@ -0,0 +1,62 @@
+package legacy
+
+import (
+	"errors"
+
+	"tinygo.org/x/drivers/internal/pin"
+)
+
+// The pingconfig group of files serve to abstract away
+// pin configuration calls on the machine.Pin type.
+// It was observed this way of developing drivers was
+// non-portable and unusable on "big" Go projects so
+// future projects should NOT configure pins in driver code.
+// Users must configure pins before passing them as arguments
+// to drivers.
+
+// ConfigurePinOut is a legacy function used to configure pins as outputs.
+//
+// Deprecated: Do not configure pins in drivers.
+// This is a legacy feature and should only be used by drivers that
+// previously configured pins in initialization to avoid breaking users.
+func ConfigurePinOut(po pin.Output) {
+	configurePinOut(po)
+}
+
+// ConfigurePinInput is a legacy function used to configure pins as inputs.
+//
+// Deprecated: Do not configure pins in drivers.
+// This is a legacy feature and should only be used by drivers that
+// previously configured pins in initialization to avoid breaking users.
+func ConfigurePinInputPulldown(pi pin.Input) {
+	configurePinInputPulldown(pi)
+}
+
+// ConfigurePinInput is a legacy function used to configure pins as inputs.
+//
+// Deprecated: Do not configure pins in drivers.
+// This is a legacy feature and should only be used by drivers that
+// previously configured pins in initialization to avoid breaking users.
+func ConfigurePinInput(pi pin.Input) {
+	configurePinInput(pi)
+}
+
+// ConfigurePinInput is a legacy function used to configure pins as inputs.
+//
+// Deprecated: Do not configure pins in drivers.
+// This is a legacy feature and should only be used by drivers that
+// previously configured pins in initialization to avoid breaking users.
+func ConfigurePinInputPullup(pi pin.Input) {
+	configurePinInputPullup(pi)
+}
+
+// PinIsNoPin returns true if the argument is a machine.Pin type and is the machine.NoPin predeclared type.
+//
+// Deprecated: Drivers do not require pin knowledge from now on.
+func PinIsNoPin(pin any) bool {
+	return pinIsNoPin(pin)
+}
+
+var (
+	ErrConfigBeforeInstantiated = errors.New("device must be instantiated with New before calling Configure method")
+)

internal/legacy/pinconfig_go.go

@@ -0,0 +1,15 @@
+//go:build !tinygo
+
+package legacy
+
+import "tinygo.org/x/drivers/internal/pin"
+
+// This file compiles for non-tinygo builds
+// for use with "big" or "upstream" Go where
+// there is no machine package.
+
+func configurePinOut(p pin.Output)          {}
+func configurePinInput(p pin.Input)         {}
+func configurePinInputPulldown(p pin.Input) {}
+func configurePinInputPullup(p pin.Input)   {}
+func pinIsNoPin(a any) bool                 { return false }

internal/legacy/pinconfig_nopulls.go

@@ -0,0 +1,10 @@
+//go:build baremetal && fe310
+
+package legacy
+
+import "machine"
+
+const (
+	pulldown = machine.PinInput
+	pullup   = machine.PinInput
+)

internal/legacy/pinconfig_pulls.go

@@ -0,0 +1,13 @@
+//go:build baremetal && !fe310
+
+package legacy
+
+import "machine"
+
+// If you are getting a build error here you then we missed adding
+// your CPU build tag to the list of CPUs that do not have pulldown/pullups.
+// Add it above and in pinhal_nopulls! You should also add a smoketest for it :)
+const (
+	pulldown = machine.PinInputPulldown
+	pullup   = machine.PinInputPullup
+)

internal/legacy/pinconfig_tinygo.go

@@ -0,0 +1,37 @@
+//go:build baremetal
+
+package legacy
+
+import (
+	"machine"
+
+	"tinygo.org/x/drivers/internal/pin"
+)
+
+func configurePinOut(po pin.Output) {
+	configurePin(po, machine.PinOutput)
+}
+
+func configurePinInputPulldown(pi pin.Input) {
+	configurePin(pi, pulldown) // some chips do not have pull down, in which case pulldown==machine.PinInput.
+}
+
+func configurePinInput(pi pin.Input) {
+	configurePin(pi, machine.PinInput)
+}
+
+func configurePinInputPullup(pi pin.Input) {
+	configurePin(pi, pullup) // some chips do not have pull up, in which case pullup==machine.PinInput.
+}
+
+func pinIsNoPin(a any) bool {
+	p, ok := a.(machine.Pin)
+	return ok && p == machine.NoPin
+}
+
+func configurePin(p any, mode machine.PinMode) {
+	machinePin, ok := p.(machine.Pin)
+	if ok {
+		machinePin.Configure(machine.PinConfig{Mode: mode})
+	}
+}

internal/pin/internalpin.go

@@ -0,0 +1,72 @@
+// package pin implements a TinyGo Pin HAL.
+// It serves to eliminate machine.Pin from driver constructors
+// so that drivers can be used in "big" Go projects where
+// there is no machine package.
+// This file contains both function and interface-style Pin HAL definitions.
+package pin
+
+// OutputFunc is hardware abstraction for a pin which outputs a
+// digital signal (high or low level).
+//
+//	// Code conversion demo: from machine.Pin to pin.OutputFunc
+//	led := machine.LED
+//	led.Configure(machine.PinConfig{Mode: machine.Output})
+//	var pin pin.OutputFunc = led.Set // Going from a machine.Pin to a pin.OutputFunc
+//
+// This is an alternative to [Output] which is an interface type.
+type OutputFunc func(level bool)
+
+// High sets the underlying pin's level to high. This is equivalent to calling PinOutput(true).
+func (setPin OutputFunc) High() {
+	setPin(true)
+}
+
+// Low sets the underlying pin's level to low. This is equivalent to calling PinOutput(false).
+func (setPin OutputFunc) Low() {
+	setPin(false)
+}
+
+// InputFunc is hardware abstraction for a pin which receives a
+// digital signal and reads it (high or low level).
+//
+//	// Code conversion demo: from machine.Pin to pin.InputFunc
+//	input := machine.LED
+//	input.Configure(machine.PinConfig{Mode: machine.PinInputPulldown}) // or use machine.PinInputPullup or machine.Input
+//	var pin pin.InputFunc = input.Get // Going from a machine.Pin to a pin.InputFunc
+//
+// This is an alternative to [Input] which is an interface type.
+type InputFunc func() (level bool)
+
+// // Below is an example on how to define a input/output pin HAL for a
+// // pin that must switch between input and output mode:
+//
+// 	var pinIsOutput bool
+// 	var po PinOutputFunc = func(b bool) {
+// 		if !pinIsOutput {
+// 			pin.Configure(outputMode)
+// 			pinIsOutput = true
+// 		}
+// 		pin.Set(b)
+// 	}
+//
+// 	var pi PinInputFunc = func() bool {
+// 		if pinIsOutput {
+// 			pin.Configure(inputMode)
+// 			pinIsOutput = false
+// 		}
+// 		return pin.Get()
+// 	}
+
+// Output interface represents a pin hardware abstraction layer for a pin that can output a digital signal.
+//
+// This is an alternative to [OutputFunc] abstraction which is a function type.
+type Output interface {
+	Set(level bool)
+}
+
+// Input interface represents a pin hardware abstraction layer for a pin that can read a digital signal.
+//
+// This is an alternative to [InputFunc] abstraction which is a function type.
+type Input interface {
+	Get() (level bool)
+}

internal/regmap/device8.go

@@ -0,0 +1,143 @@
+package regmap
+
+import (
+	"encoding/binary"
+	"io"
+
+	"tinygo.org/x/drivers"
+)
+
+// Device8 implements common logic to most 8-bit peripherals with an I2C or SPI bus.
+// All methods expect the target to support conventional register read and write operations
+// where the first byte sent is the register address being accessed.
+//
+// All methods use an internal buffer and perform no dynamic memory allocation.
+type Device8 struct {
+	buf [10]byte
+}
+
+// clear zeroes Device8's buffers.
+func (d *Device8) clear() {
+	d.buf = [10]byte{}
+}
+
+// I2C methods.
+
+// Read8I2C reads a single byte from register addr of the device at i2cAddr using the provided I2C bus.
+func (d *Device8) Read8I2C(bus drivers.I2C, i2cAddr uint16, addr uint8) (byte, error) {
+	d.buf[0] = addr
+	err := bus.Tx(i2cAddr, d.buf[0:1], d.buf[1:2])
+	return d.buf[1], err
+}
+
+// Read16I2C reads a 16-bit value from register addr of the device at i2cAddr using the provided I2C bus.
+// The byte order is specified by order.
+func (d *Device8) Read16I2C(bus drivers.I2C, i2cAddr uint16, addr uint8, order binary.ByteOrder) (uint16, error) {
+	d.buf[0] = addr
+	err := bus.Tx(i2cAddr, d.buf[0:1], d.buf[1:3])
+	return order.Uint16(d.buf[1:3]), err
+}
+
+// Read32I2C reads a 32-bit value from register addr of the device at i2cAddr using the provided I2C bus.
+// The byte order is specified by order.
+func (d *Device8) Read32I2C(bus drivers.I2C, i2cAddr uint16, addr uint8, order binary.ByteOrder) (uint32, error) {
+	d.buf[0] = addr
+	err := bus.Tx(i2cAddr, d.buf[0:1], d.buf[1:5])
+	return order.Uint32(d.buf[1:5]), err
+}
+
+// ReadDataI2C reads dataLength bytes from register addr of the device at i2cAddr using the provided I2C bus.
+// The data is stored in dataDestination.
+func (d *Device8) ReadDataI2C(bus drivers.I2C, i2cAddr uint16, addr uint8, dataDestination []byte) error {
+	d.buf[0] = addr
+	return bus.Tx(i2cAddr, d.buf[:1], dataDestination)
+}
+
+// Write8I2C writes a single byte value to register addr of the device at i2cAddr using the provided I2C bus.
+func (d *Device8) Write8I2C(bus drivers.I2C, i2cAddr uint16, addr, value uint8) error {
+	d.buf[0] = addr
+	d.buf[1] = value
+	return bus.Tx(i2cAddr, d.buf[:2], nil)
+}
+
+// Write16I2C writes a 16-bit value to register addr of the device at i2cAddr using the provided I2C bus.
+// The byte order is specified by order.
+func (d *Device8) Write16I2C(bus drivers.I2C, i2cAddr uint16, addr uint8, value uint16, order binary.ByteOrder) error {
+	d.buf[0] = addr
+	order.PutUint16(d.buf[1:3], value)
+	return bus.Tx(i2cAddr, d.buf[0:3], nil)
+}
+
+// Write32I2C writes a 32-bit value to register addr of the device at i2cAddr using the provided I2C bus.
+// The byte order is specified by order.
+func (d *Device8) Write32I2C(bus drivers.I2C, i2cAddr uint16, addr uint8, value uint32, order binary.ByteOrder) error {
+	d.buf[0] = addr
+	order.PutUint32(d.buf[1:5], value)
+	return bus.Tx(i2cAddr, d.buf[0:5], nil)
+}
+
+// SPI methods.
+
+// Read8SPI reads a single byte from register addr using the provided SPI bus.
+func (d *Device8) Read8SPI(bus drivers.SPI, addr uint8) (byte, error) {
+	d.clear()
+	d.buf[0] = addr
+	err := bus.Tx(d.buf[0:1], d.buf[1:2]) // We suppose data is returned after first byte in SPI.
+	return d.buf[1], err
+}
+
+// Read16SPI reads a 16-bit value from register addr using the provided SPI bus. The byte order is specified by order.
+func (d *Device8) Read16SPI(bus drivers.SPI, addr uint8, order binary.ByteOrder) (uint16, error) {
+	d.clear()
+	d.buf[0] = addr
+	err := bus.Tx(d.buf[0:3], d.buf[3:6]) // We suppose data is returned after first byte in SPI.
+	return order.Uint16(d.buf[4:6]), err
+}
+
+// Read32SPI reads a 32-bit value from register addr using the provided SPI bus. The byte order is specified by order.
+func (d *Device8) Read32SPI(bus drivers.SPI, addr uint8, order binary.ByteOrder) (uint32, error) {
+	d.clear()
+	d.buf[0] = addr
+	err := bus.Tx(d.buf[0:5], d.buf[5:10]) // We suppose data is returned after first byte in SPI.
+	return order.Uint32(d.buf[6:10]), err
+}
+
+// ReadDataSPI reads data from a 8bit device address. It assumes data at register address is sent back
+// from device after first byte is written as address.
+// It needs the auxiliary buffer length to be large enough to contain both the write and read portions of buffer,
+// so 2*(dataLength+1) < len(auxiliaryBuf) must hold.
+func (d *Device8) ReadDataSPI(bus drivers.SPI, addr uint8, dataLength int, auxiliaryBuf []byte) ([]byte, error) {
+	split := len(auxiliaryBuf) / 2
+	if split < dataLength+1 {
+		return nil, io.ErrShortBuffer
+	}
+
+	wbuf, rbuf := auxiliaryBuf[:split], auxiliaryBuf[split:]
+	wbuf[0] = addr
+	err := bus.Tx(wbuf, rbuf)
+	return rbuf[1:], err
+}
+
+// Write8SPI writes a single byte value to register addr using the provided SPI bus.
+func (d *Device8) Write8SPI(bus drivers.SPI, addr, value uint8) error {
+	d.clear()
+	d.buf[0] = addr
+	d.buf[1] = value
+	return bus.Tx(d.buf[:2], nil)
+}
+
+// Write16SPI writes a 16-bit value to register addr using the provided SPI bus. The byte order is specified by order.
+func (d *Device8) Write16SPI(bus drivers.SPI, addr uint8, value uint16, order binary.ByteOrder) error {
+	d.clear()
+	d.buf[0] = addr
+	order.PutUint16(d.buf[1:3], value)
+	return bus.Tx(d.buf[:3], nil)
+}
+
+// Write32SPI writes a 32-bit value to register addr using the provided SPI bus. The byte order is specified by order.
+func (d *Device8) Write32SPI(bus drivers.SPI, addr uint8, value uint32, order binary.ByteOrder) error {
+	d.clear()
+	d.buf[0] = addr
+	order.PutUint32(d.buf[1:5], value)
+	return bus.Tx(d.buf[:5], nil)
+}

internal/regmap/i2c-spi.go

@@ -0,0 +1,123 @@
+package regmap
+
+import (
+	"encoding/binary"
+
+	"tinygo.org/x/drivers"
+)
+
+// Device8SPI implements common logic to most 8-bit peripherals with an SPI bus.
+// All methods expect the target to support conventional register read and write operations
+// where the first byte sent is the register address being accessed.
+//
+// All methods use an internal buffer and perform no dynamic memory allocation.
+type Device8SPI struct {
+	bus   drivers.SPI
+	order binary.ByteOrder
+	d     Device8
+}
+
+// SetBus sets the SPI bus and byte order for the Device8SPI.
+//
+// As a hint, most SPI devices use big-endian (MSB) byte order.
+//   - Big endian: A value of 0x1234 is transmitted as 0x12 followed by 0x34.
+//   - Little endian: A value of 0x1234 is transmitted as 0x34 followed by 0x12.
+func (d *Device8SPI) SetBus(bus drivers.SPI, order binary.ByteOrder) {
+	d.bus = bus
+	d.order = order
+}
+
+// Read8 reads a single byte from register addr.
+func (d *Device8SPI) Read8(addr uint8) (byte, error) {
+	return d.d.Read8SPI(d.bus, addr)
+}
+
+// Read16 reads a 16-bit value from register addr.
+func (d *Device8SPI) Read16(addr uint8) (uint16, error) {
+	return d.d.Read16SPI(d.bus, addr, d.order)
+}
+
+// Read32 reads a 32-bit value from register addr.
+func (d *Device8SPI) Read32(addr uint8) (uint32, error) {
+	return d.d.Read32SPI(d.bus, addr, d.order)
+}
+
+// ReadData reads dataLength bytes from register addr. Due to the internal functioning of
+// SPI, an auxiliary buffer must be provided to perform the operation and avoid memory allocation.
+// The returned slice is a subslice of auxBuffer containing the read data.
+func (d *Device8SPI) ReadData(addr uint8, datalength int, auxBuffer []byte) ([]byte, error) {
+	return d.d.ReadDataSPI(d.bus, addr, datalength, auxBuffer)
+}
+
+// Write8 writes a single byte value to register addr.
+func (d *Device8SPI) Write8(addr, value uint8) error {
+	return d.d.Write8SPI(d.bus, addr, value)
+}
+
+// Write16 writes a 16-bit value to register addr.
+func (d *Device8SPI) Write16(addr uint8, value uint16) error {
+	return d.d.Write16SPI(d.bus, addr, value, d.order)
+}
+
+// Write32 writes a 32-bit value to register addr.
+func (d *Device8SPI) Write32(addr uint8, value uint32) error {
+	return d.d.Write32SPI(d.bus, addr, value, d.order)
+}
+
+// Device8I2C implements common logic to most 8-bit peripherals with an I2C bus.
+// All methods expect the target to support conventional register read and write operations
+// where the first byte sent is the register address being accessed.
+//
+// All methods use an internal buffer and perform no dynamic memory allocation.
+type Device8I2C struct {
+	bus     drivers.I2C
+	i2cAddr uint16
+	order   binary.ByteOrder
+	d       Device8
+}
+
+// SetBus sets the I2C bus, device address, and byte order for the Device8I2C.
+//
+// As a hint, most I2C devices use big-endian (MSB) byte order.
+//   - Big endian: A value of 0x1234 is transmitted as 0x12 followed by 0x34.
+//   - Little endian: A value of 0x1234 is transmitted as 0x34 followed by 0x12.
+func (d *Device8I2C) SetBus(bus drivers.I2C, i2cAddr uint16, order binary.ByteOrder) {
+	d.bus = bus
+	d.i2cAddr = i2cAddr
+	d.order = order
+}
+
+// Read8 reads a single byte from register addr.
+func (d *Device8I2C) Read8(addr uint8) (byte, error) {
+	return d.d.Read8I2C(d.bus, d.i2cAddr, addr)
+}
+
+// Read16 reads a 16-bit value from register addr.
+func (d *Device8I2C) Read16(addr uint8) (uint16, error) {
+	return d.d.Read16I2C(d.bus, d.i2cAddr, addr, d.order)
+}
+
+// Read32 reads a 32-bit value from register addr.
+func (d *Device8I2C) Read32(addr uint8) (uint32, error) {
+	return d.d.Read32I2C(d.bus, d.i2cAddr, addr, d.order)
+}
+
+// ReadData reads dataLength bytes from register addr.
+func (d *Device8I2C) ReadData(addr uint8, dataDestination []byte) error {
+	return d.d.ReadDataI2C(d.bus, d.i2cAddr, addr, dataDestination)
+}
+
+// Write8 writes a single byte value to register addr.
+func (d *Device8I2C) Write8(addr, value uint8) error {
+	return d.d.Write8I2C(d.bus, d.i2cAddr, addr, value)
+}
+
+// Write16 writes a 16-bit value to register addr.
+func (d *Device8I2C) Write16(addr uint8, value uint16) error {
+	return d.d.Write16I2C(d.bus, d.i2cAddr, addr, value, d.order)
+}
+
+// Write32 writes a 32-bit value to register addr.
+func (d *Device8I2C) Write32(addr uint8, value uint32) error {
+	return d.d.Write32I2C(d.bus, d.i2cAddr, addr, value, d.order)
+}

lis3dh/lis3dh.go

@@ -11,37 +11,57 @@ import (
 // Device wraps an I2C connection to a LIS3DH device.
 type Device struct {
 	bus     drivers.I2C
-	Address uint16
+	address uint16
 	r       Range
+	accel   [6]byte // stored acceleration data (from the Update call)
+}
+
+// Driver configuration, used for the Configure call. All fields are optional.
+type Config struct {
+	Address uint16
 }
 
 // New creates a new LIS3DH connection. The I2C bus must already be configured.
 //
 // This function only creates the Device object, it does not touch the device.
 func New(bus drivers.I2C) Device {
-	return Device{bus: bus, Address: Address0}
+	return Device{bus: bus, address: Address0}
 }
 
 // Configure sets up the device for communication
-func (d *Device) Configure() {
+func (d *Device) Configure(config Config) error {
+	if config.Address != 0 {
+		d.address = config.Address
+	}
+
 	// enable all axes, normal mode
-	legacy.WriteRegister(d.bus, uint8(d.Address), REG_CTRL1, []byte{0x07})
+	err := legacy.WriteRegister(d.bus, uint8(d.address), REG_CTRL1, []byte{0x07})
+	if err != nil {
+		return err
+	}
 
 	// 400Hz rate
-	d.SetDataRate(DATARATE_400_HZ)
+	err = d.SetDataRate(DATARATE_400_HZ)
+	if err != nil {
+		return err
+	}
 
 	// High res & BDU enabled
-	legacy.WriteRegister(d.bus, uint8(d.Address), REG_CTRL4, []byte{0x88})
+	err = legacy.WriteRegister(d.bus, uint8(d.address), REG_CTRL4, []byte{0x88})
+	if err != nil {
+		return err
+	}
 
 	// get current range
-	d.r = d.ReadRange()
+	d.r, err = d.ReadRange()
+	return err
 }
 
 // Connected returns whether a LIS3DH has been found.
 // It does a "who am I" request and checks the response.
 func (d *Device) Connected() bool {
 	data := []byte{0}
-	err := legacy.ReadRegister(d.bus, uint8(d.Address), WHO_AM_I, data)
+	err := legacy.ReadRegister(d.bus, uint8(d.address), WHO_AM_I, data)
 	if err != nil {
 		return false
 	}
@@ -49,46 +69,51 @@ func (d *Device) Connected() bool {
 }
 
 // SetDataRate sets the speed of data collected by the LIS3DH.
-func (d *Device) SetDataRate(rate DataRate) {
+func (d *Device) SetDataRate(rate DataRate) error {
 	ctl1 := []byte{0}
-	err := legacy.ReadRegister(d.bus, uint8(d.Address), REG_CTRL1, ctl1)
+	err := legacy.ReadRegister(d.bus, uint8(d.address), REG_CTRL1, ctl1)
 	if err != nil {
-		println(err.Error())
+		return err
 	}
 	// mask off bits
 	ctl1[0] &^= 0xf0
 	ctl1[0] |= (byte(rate) << 4)
-	legacy.WriteRegister(d.bus, uint8(d.Address), REG_CTRL1, ctl1)
+	return legacy.WriteRegister(d.bus, uint8(d.address), REG_CTRL1, ctl1)
 }
 
 // SetRange sets the G range for LIS3DH.
-func (d *Device) SetRange(r Range) {
+func (d *Device) SetRange(r Range) error {
 	ctl := []byte{0}
-	err := legacy.ReadRegister(d.bus, uint8(d.Address), REG_CTRL4, ctl)
+	err := legacy.ReadRegister(d.bus, uint8(d.address), REG_CTRL4, ctl)
 	if err != nil {
-		println(err.Error())
+		return err
 	}
 	// mask off bits
 	ctl[0] &^= 0x30
 	ctl[0] |= (byte(r) << 4)
-	legacy.WriteRegister(d.bus, uint8(d.Address), REG_CTRL4, ctl)
+	err = legacy.WriteRegister(d.bus, uint8(d.address), REG_CTRL4, ctl)
+	if err != nil {
+		return err
+	}
 
 	// store the new range
 	d.r = r
+
+	return nil
 }
 
 // ReadRange returns the current G range for LIS3DH.
-func (d *Device) ReadRange() (r Range) {
+func (d *Device) ReadRange() (r Range, err error) {
 	ctl := []byte{0}
-	err := legacy.ReadRegister(d.bus, uint8(d.Address), REG_CTRL4, ctl)
+	err = legacy.ReadRegister(d.bus, uint8(d.address), REG_CTRL4, ctl)
 	if err != nil {
-		println(err.Error())
+		return 0, err
 	}
 	// mask off bits
 	r = Range(ctl[0] >> 4)
 	r &= 0x03
 
-	return r
+	return r, nil
 }
 
 // ReadAcceleration reads the current acceleration from the device and returns
@@ -96,28 +121,17 @@ func (d *Device) ReadRange() (r Range) {
 // and the sensor is not moving the returned value will be around 1000000 or
 // -1000000.
 func (d *Device) ReadAcceleration() (int32, int32, int32, error) {
-	x, y, z := d.ReadRawAcceleration()
-	divider := float32(1)
-	switch d.r {
-	case RANGE_16_G:
-		divider = 1365
-	case RANGE_8_G:
-		divider = 4096
-	case RANGE_4_G:
-		divider = 8190
-	case RANGE_2_G:
-		divider = 16380
-	}
-
-	return int32(float32(x) / divider * 1000000), int32(float32(y) / divider * 1000000), int32(float32(z) / divider * 1000000), nil
+	rawX, rawY, rawZ := d.ReadRawAcceleration()
+	x, y, z := normalizeRange(rawX, rawY, rawZ, d.r)
+	return x, y, z, nil
 }
 
 // ReadRawAcceleration returns the raw x, y and z axis from the LIS3DH
 func (d *Device) ReadRawAcceleration() (x int16, y int16, z int16) {
-	legacy.WriteRegister(d.bus, uint8(d.Address), REG_OUT_X_L|0x80, nil)
+	legacy.WriteRegister(d.bus, uint8(d.address), REG_OUT_X_L|0x80, nil)
 
 	data := []byte{0, 0, 0, 0, 0, 0}
-	d.bus.Tx(d.Address, nil, data)
+	d.bus.Tx(d.address, nil, data)
 
 	x = int16((uint16(data[1]) << 8) | uint16(data[0]))
 	y = int16((uint16(data[3]) << 8) | uint16(data[2]))
@@ -125,3 +139,68 @@ func (d *Device) ReadRawAcceleration() (x int16, y int16, z int16) {
 
 	return
 }
+
+// Update the sensor values of the 'which' parameter. Only acceleration is
+// supported at the moment.
+func (d *Device) Update(which drivers.Measurement) error {
+	if which&drivers.Acceleration != 0 {
+		// Read raw acceleration values and store them in the driver.
+		err := legacy.WriteRegister(d.bus, uint8(d.address), REG_OUT_X_L|0x80, nil)
+		if err != nil {
+			return err
+		}
+		err = d.bus.Tx(d.address, nil, d.accel[:])
+		if err != nil {
+			return err
+		}
+	}
+	return nil
+}
+
+// Acceleration returns the last read acceleration in µg (micro-gravity).
+// When one of the axes is pointing straight to Earth and the sensor is not
+// moving the returned value will be around 1000000 or -1000000.
+func (d *Device) Acceleration() (x, y, z int32) {
+	// Extract the raw 16-bit values.
+	rawX := int16((uint16(d.accel[1]) << 8) | uint16(d.accel[0]))
+	rawY := int16((uint16(d.accel[3]) << 8) | uint16(d.accel[2]))
+	rawZ := int16((uint16(d.accel[5]) << 8) | uint16(d.accel[4]))
+
+	// Normalize these values, to be in µg (micro-gravity).
+	return normalizeRange(rawX, rawY, rawZ, d.r)
+}
+
+// Convert raw 16-bit values to normalized 32-bit values while avoiding floats
+// and divisions.
+func normalizeRange(rawX, rawY, rawZ int16, r Range) (x, y, z int32) {
+	// We're going to convert the 16-bit raw values to values in the range
+	// -1000_000..1000_000. For now we're going to assume a range of 16G, we'll
+	// adjust that range later.
+	// The formula is derived as follows, and carefully selected to avoid
+	// overflow and integer divisions (the division will be optimized to a
+	// bitshift):
+	//   x = x * 1000_000      / 2048
+	//   x = x * (1000_000/64) / (2048/64)
+	//   x = x * 15625         / 32
+	x = int32(rawX) * 15625 / 32
+	y = int32(rawY) * 15625 / 32
+	z = int32(rawZ) * 15625 / 32
+
+	// Now we need to normalize the three values, since we assumed 16G before.
+	shift := uint32(0)
+	switch r {
+	case RANGE_16_G:
+		shift = 0
+	case RANGE_8_G:
+		shift = 1
+	case RANGE_4_G:
+		shift = 2
+	case RANGE_2_G:
+		shift = 3
+	}
+	x >>= shift
+	y >>= shift
+	z >>= shift
+
+	return
+}

lsm9ds1/lsm9ds1.go

@@ -7,7 +7,6 @@ import (
 	"errors"
 
 	"tinygo.org/x/drivers"
-	"tinygo.org/x/drivers/internal/legacy"
 )
 
 type AccelRange uint8
@@ -28,7 +27,7 @@ type Device struct {
 	accelMultiplier int32
 	gyroMultiplier  int32
 	magMultiplier   int32
-	buf             [6]uint8
+	buf             [7]uint8 // up to 6 bytes for read + 1 byte for the register address
 }
 
 // Configuration for LSM9DS1 device.
@@ -61,10 +60,15 @@ func New(bus drivers.I2C) *Device {
 // Case of boolean false and error nil means I2C is up,
 // but "who am I" responses have unexpected values.
 func (d *Device) Connected() bool {
-	data1, data2 := d.buf[:1], d.buf[1:2]
-	legacy.ReadRegister(d.bus, d.AccelAddress, WHO_AM_I, data1)
-	legacy.ReadRegister(d.bus, d.MagAddress, WHO_AM_I_M, data2)
-	return data1[0] == 0x68 && data2[0] == 0x3D
+	data, err := d.readBytes(d.AccelAddress, WHO_AM_I, 1)
+	if err != nil || data[0] != 0x68 {
+		return false
+	}
+	data, err = d.readBytes(d.MagAddress, WHO_AM_I_M, 1)
+	if err != nil || data[0] != 0x3D {
+		return false
+	}
+	return true
 }
 
 // ReadAcceleration reads the current acceleration from the device and returns
@@ -72,8 +76,7 @@ func (d *Device) Connected() bool {
 // and the sensor is not moving the returned value will be around 1000000 or
 // -1000000.
 func (d *Device) ReadAcceleration() (x, y, z int32, err error) {
-	data := d.buf[:6]
-	err = legacy.ReadRegister(d.bus, uint8(d.AccelAddress), OUT_X_L_XL, data)
+	data, err := d.readBytes(d.AccelAddress, OUT_X_L_XL, 6)
 	if err != nil {
 		return
 	}
@@ -88,8 +91,7 @@ func (d *Device) ReadAcceleration() (x, y, z int32, err error) {
 // rotation along one axis and while doing so integrate all values over time,
 // you would get a value close to 360000000.
 func (d *Device) ReadRotation() (x, y, z int32, err error) {
-	data := d.buf[:6]
-	err = legacy.ReadRegister(d.bus, uint8(d.AccelAddress), OUT_X_L_G, data)
+	data, err := d.readBytes(d.AccelAddress, OUT_X_L_G, 6)
 	if err != nil {
 		return
 	}
@@ -102,8 +104,7 @@ func (d *Device) ReadRotation() (x, y, z int32, err error) {
 // ReadMagneticField reads the current magnetic field from the device and returns
 // it in nT (nanotesla). 1 G (gauss) = 100_000 nT (nanotesla).
 func (d *Device) ReadMagneticField() (x, y, z int32, err error) {
-	data := d.buf[:6]
-	err = legacy.ReadRegister(d.bus, uint8(d.MagAddress), OUT_X_L_M, data)
+	data, err := d.readBytes(d.MagAddress, OUT_X_L_M, 6)
 	if err != nil {
 		return
 	}
@@ -115,8 +116,7 @@ func (d *Device) ReadMagneticField() (x, y, z int32, err error) {
 
 // ReadTemperature returns the temperature in Celsius milli degrees (°C/1000)
 func (d *Device) ReadTemperature() (t int32, err error) {
-	data := d.buf[:2]
-	err = legacy.ReadRegister(d.bus, uint8(d.AccelAddress), OUT_TEMP_L, data)
+	data, err := d.readBytes(d.AccelAddress, OUT_TEMP_L, 2)
 	if err != nil {
 		return
 	}
@@ -167,20 +167,16 @@ func (d *Device) doConfigure(cfg Configuration) (err error) {
 		d.magMultiplier = 58
 	}
 
-	data := d.buf[:1]
-
 	// Configure accelerometer
 	// Sample rate & measurement range
-	data[0] = uint8(cfg.AccelSampleRate)<<5 | uint8(cfg.AccelRange)<<3
-	err = legacy.WriteRegister(d.bus, d.AccelAddress, CTRL_REG6_XL, data)
+	err = d.writeByte(d.AccelAddress, CTRL_REG6_XL, uint8(cfg.AccelSampleRate)<<5|uint8(cfg.AccelRange)<<3)
 	if err != nil {
 		return
 	}
 
 	// Configure gyroscope
 	// Sample rate & measurement range
-	data[0] = uint8(cfg.GyroSampleRate)<<5 | uint8(cfg.GyroRange)<<3
-	err = legacy.WriteRegister(d.bus, d.AccelAddress, CTRL_REG1_G, data)
+	err = d.writeByte(d.AccelAddress, CTRL_REG1_G, uint8(cfg.GyroSampleRate)<<5|uint8(cfg.GyroRange)<<3)
 	if err != nil {
 		return
 	}
@@ -190,33 +186,44 @@ func (d *Device) doConfigure(cfg Configuration) (err error) {
 	// Temperature compensation enabled
 	// High-performance mode XY axis
 	// Sample rate
-	data[0] = 0b10000000 | 0b01000000 | uint8(cfg.MagSampleRate)<<2
-	err = legacy.WriteRegister(d.bus, d.MagAddress, CTRL_REG1_M, data)
+	err = d.writeByte(d.MagAddress, CTRL_REG1_M, 0b10000000|0b01000000|uint8(cfg.MagSampleRate)<<2)
 	if err != nil {
 		return
 	}
 
 	// Measurement range
-	data[0] = uint8(cfg.MagRange) << 5
-	err = legacy.WriteRegister(d.bus, d.MagAddress, CTRL_REG2_M, data)
+	err = d.writeByte(d.MagAddress, CTRL_REG2_M, uint8(cfg.MagRange)<<5)
 	if err != nil {
 		return
 	}
 
 	// Continuous-conversion mode
 	// https://electronics.stackexchange.com/questions/237397/continuous-conversion-vs-single-conversion-mode
-	data[0] = 0b00000000
-	err = legacy.WriteRegister(d.bus, d.MagAddress, CTRL_REG3_M, data)
+	err = d.writeByte(d.MagAddress, CTRL_REG3_M, 0b00000000)
 	if err != nil {
 		return
 	}
 
 	// High-performance mode Z axis
-	data[0] = 0b00001000
-	err = legacy.WriteRegister(d.bus, d.MagAddress, CTRL_REG4_M, data)
+	err = d.writeByte(d.MagAddress, CTRL_REG4_M, 0b00001000)
 	if err != nil {
 		return
 	}
 
 	return nil
 }
+
+func (d *Device) readBytes(addr, reg, size uint8) ([]byte, error) {
+	d.buf[0] = reg
+	err := d.bus.Tx(uint16(addr), d.buf[0:1], d.buf[1:size+1])
+	if err != nil {
+		return nil, err
+	}
+	return d.buf[1 : size+1], nil
+}
+
+func (d *Device) writeByte(addr, reg, value uint8) error {
+	d.buf[0] = reg
+	d.buf[1] = value
+	return d.bus.Tx(uint16(addr), d.buf[0:2], nil)
+}

max6675/max6675.go

@@ -3,9 +3,9 @@ package max6675
 
 import (
 	"errors"
-	"machine"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 // ErrThermocoupleOpen is returned when the thermocouple input is open.
@@ -14,16 +14,16 @@ var ErrThermocoupleOpen = errors.New("thermocouple input open")
 
 type Device struct {
 	bus drivers.SPI
-	cs  machine.Pin
+	cs  pin.OutputFunc
 }
 
 // Create a new Device to read from a MAX6675 thermocouple.
 // Pins must be configured before use.  Frequency for SPI
 // should be 4.3MHz maximum.
-func NewDevice(bus drivers.SPI, cs machine.Pin) *Device {
+func NewDevice(bus drivers.SPI, cs pin.Output) *Device {
 	return &Device{
 		bus: bus,
-		cs:  cs,
+		cs:  cs.Set,
 	}
 }
 

max72xx/max72xx.go

@@ -3,31 +3,36 @@
 package max72xx
 
 import (
-	"machine"
-
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 type Device struct {
-	bus drivers.SPI
-	cs  machine.Pin
+	bus           drivers.SPI
+	cs            pin.OutputFunc
+	configurePins func()
 }
 
 // NewDriver creates a new max7219 connection. The SPI wire must already be configured
 // The SPI frequency must not be higher than 10MHz.
 // parameter cs: the datasheet also refers to this pin as "load" pin.
-func NewDevice(bus drivers.SPI, cs machine.Pin) *Device {
+func NewDevice(bus drivers.SPI, cs pin.Output) *Device {
 	return &Device{
 		bus: bus,
-		cs:  cs,
+		cs:  cs.Set,
+		configurePins: func() {
+			legacy.ConfigurePinOut(cs)
+		},
 	}
 }
 
 // Configure setups the pins.
 func (driver *Device) Configure() {
-	outPutConfig := machine.PinConfig{Mode: machine.PinOutput}
-
-	driver.cs.Configure(outPutConfig)
+	if driver.configurePins == nil {
+		panic(legacy.ErrConfigBeforeInstantiated)
+	}
+	driver.configurePins()
 }
 
 // SetScanLimit sets the scan limit. Maximum is 8.

mcp2515/mcp2515.go

@@ -8,18 +8,20 @@ package mcp2515 // import "tinygo.org/x/drivers/mcp2515"
 import (
 	"errors"
 	"fmt"
-	"machine"
 	"time"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 // Device wraps MCP2515 SPI CAN Module.
 type Device struct {
-	spi     SPI
-	cs      machine.Pin
-	msg     *CANMsg
-	mcpMode byte
+	spi           SPI
+	cs            pin.OutputFunc
+	msg           *CANMsg
+	mcpMode       byte
+	configurePins func()
 }
 
 // CANMsg stores CAN message fields.
@@ -36,15 +38,18 @@ const (
 )
 
 // New returns a new MCP2515 driver. Pass in a fully configured SPI bus.
-func New(b drivers.SPI, csPin machine.Pin) *Device {
+func New(b drivers.SPI, csPin pin.Output) *Device {
 	d := &Device{
 		spi: SPI{
 			bus: b,
 			tx:  make([]byte, 0, bufferSize),
 			rx:  make([]byte, 0, bufferSize),
 		},
-		cs:  csPin,
+		cs:  csPin.Set,
 		msg: &CANMsg{},
+		configurePins: func() {
+			legacy.ConfigurePinOut(csPin)
+		},
 	}
 
 	return d
@@ -52,7 +57,10 @@ func New(b drivers.SPI, csPin machine.Pin) *Device {
 
 // Configure sets up the device for communication.
 func (d *Device) Configure() {
-	d.cs.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	if d.configurePins == nil {
+		panic(legacy.ErrConfigBeforeInstantiated)
+	}
+	d.configurePins()
 }
 
 const beginTimeoutValue int = 10

onewire/onewire.go

@@ -5,8 +5,9 @@ package onewire // import "tinygo.org/x/drivers/onewire"
 
 import (
 	"errors"
-	"machine"
 	"time"
+
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 // OneWire ROM commands
@@ -19,7 +20,8 @@ const (
 
 // Device wraps a connection to an 1-Wire devices.
 type Device struct {
-	p machine.Pin
+	set pin.OutputFunc
+	get pin.InputFunc
 }
 
 // Config wraps a configuration to an 1-Wire devices.
@@ -32,24 +34,30 @@ var (
 	errReadAddress    = errors.New("Error: OneWire. Read address error: CRC mismatch.")
 )
 
-// New creates a new GPIO 1-Wire connection.
-// The pin must be pulled up to the VCC via a resistor greater than 500 ohms (default 4.7k).
-func New(p machine.Pin) Device {
-	return Device{
-		p: p,
+// NewFromFuncs expects pin setter and getter for DQ line. Ideally this driver should receive
+// a one-wire bus HAL abstraction, but I was asked to show how this could be done using pin HAL so here goes.
+func NewFromFuncs(getPinLevel pin.InputFunc, setPinLevel pin.OutputFunc) *Device {
+	return &Device{
+		set: setPinLevel,
+		get: getPinLevel,
 	}
 }
 
 // Configure initializes the protocol.
 func (d *Device) Configure(config Config) {}
 
+// By setting the pin value one should configure as output and also expect a more
+// consistent behaviour across all tinygo hosts by pulling DQ line low consistently. Win-win.
+func (d *Device) cfgOut() { d.set.Low() }
+func (d *Device) cfgIn()  { d.get() }
+
 // Reset pull DQ line low, then up.
 func (d Device) Reset() error {
-	d.p.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	d.cfgOut()
 	time.Sleep(480 * time.Microsecond)
-	d.p.Configure(machine.PinConfig{Mode: machine.PinInputPullup})
+	d.cfgIn()
 	time.Sleep(70 * time.Microsecond)
-	precence := d.p.Get()
+	precence := d.get()
 	time.Sleep(410 * time.Microsecond)
 	if precence {
 		return errNoPresence
@@ -59,14 +67,14 @@ func (d Device) Reset() error {
 
 // WriteBit transmits a bit to 1-Wire bus.
 func (d Device) WriteBit(data uint8) {
-	d.p.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	d.cfgOut()
 	if data&1 == 1 { // Send '1'
 		time.Sleep(5 * time.Microsecond)
-		d.p.Configure(machine.PinConfig{Mode: machine.PinInputPullup})
+		d.cfgIn()
 		time.Sleep(60 * time.Microsecond)
 	} else { // Send '0'
 		time.Sleep(60 * time.Microsecond)
-		d.p.Configure(machine.PinConfig{Mode: machine.PinInputPullup})
+		d.cfgIn()
 		time.Sleep(5 * time.Microsecond)
 	}
 }
@@ -81,11 +89,11 @@ func (d Device) Write(data uint8) {
 
 // ReadBit receives a bit from 1-Wire bus.
 func (d Device) ReadBit() (data uint8) {
-	d.p.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	d.cfgOut()
 	time.Sleep(3 * time.Microsecond)
-	d.p.Configure(machine.PinConfig{Mode: machine.PinInputPullup})
+	d.cfgIn()
 	time.Sleep(8 * time.Microsecond)
-	if d.p.Get() {
+	if d.get() {
 		data = 1
 	}
 	time.Sleep(60 * time.Microsecond)

onewire/onewire_tinygo.go

@@ -0,0 +1,31 @@
+//go:build tinygo
+
+package onewire
+
+import (
+	"machine"
+
+	"tinygo.org/x/drivers/internal/legacy"
+)
+
+// New creates a new GPIO 1-Wire connection.
+// The pin must be pulled up to the VCC via a resistor greater than 500 ohms (default 4.7k).
+func New(p machine.Pin) Device {
+	isOut := false
+	return Device{
+		set: func(level bool) {
+			if !isOut {
+				legacy.ConfigurePinOut(p)
+				isOut = true
+			}
+			p.Set(level)
+		},
+		get: func() (level bool) {
+			if isOut {
+				legacy.ConfigurePinInputPullup(p)
+				isOut = false
+			}
+			return p.Get()
+		},
+	}
+}

pcd8544/pcd8544.go

@@ -6,18 +6,18 @@ package pcd8544 // import "tinygo.org/x/drivers/pcd8544"
 import (
 	"errors"
 	"image/color"
-	"machine"
 	"time"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 // Device wraps an SPI connection.
 type Device struct {
 	bus        drivers.SPI
-	dcPin      machine.Pin
-	rstPin     machine.Pin
-	scePin     machine.Pin
+	dcPin      pin.OutputFunc
+	rstPin     pin.OutputFunc
+	scePin     pin.OutputFunc
 	buffer     []byte
 	width      int16
 	height     int16
@@ -30,12 +30,12 @@ type Config struct {
 }
 
 // New creates a new PCD8544 connection. The SPI bus must already be configured.
-func New(bus drivers.SPI, dcPin, rstPin, scePin machine.Pin) *Device {
+func New(bus drivers.SPI, dcPin, rstPin, scePin pin.Output) *Device {
 	return &Device{
 		bus:    bus,
-		dcPin:  dcPin,
-		rstPin: rstPin,
-		scePin: scePin,
+		dcPin:  dcPin.Set,
+		rstPin: rstPin.Set,
+		scePin: scePin.Set,
 	}
 }
 

pixel/image_test.go

@@ -9,9 +9,30 @@ import (
 	"tinygo.org/x/drivers/pixel"
 )
 
+func TestImageRGB888(t *testing.T) {
+	image := pixel.NewImage[pixel.RGB888](5, 3)
+	if width, height := image.Size(); width != 5 || height != 3 {
+		t.Errorf("image.Size(): expected 5, 3 but got %d, %d", width, height)
+	}
+	for _, c := range []color.RGBA{
+		{R: 0xff, A: 0xff},
+		{G: 0xff, A: 0xff},
+		{B: 0xff, A: 0xff},
+		{R: 0x10, A: 0xff},
+		{G: 0x10, A: 0xff},
+		{B: 0x10, A: 0xff},
+	} {
+		image.Set(4, 2, pixel.NewColor[pixel.RGB888](c.R, c.G, c.B))
+		c2 := image.Get(4, 2).RGBA()
+		if c2 != c {
+			t.Errorf("failed to roundtrip color: expected %v but got %v", c, c2)
+		}
+	}
+}
+
 func TestImageRGB565BE(t *testing.T) {
 	image := pixel.NewImage[pixel.RGB565BE](5, 3)
-	if width, height := image.Size(); width != 5 && height != 3 {
+	if width, height := image.Size(); width != 5 || height != 3 {
 		t.Errorf("image.Size(): expected 5, 3 but got %d, %d", width, height)
 	}
 	for _, c := range []color.RGBA{
@@ -30,9 +51,30 @@ func TestImageRGB565BE(t *testing.T) {
 	}
 }
 
+func TestImageRGB555(t *testing.T) {
+	image := pixel.NewImage[pixel.RGB555](5, 3)
+	if width, height := image.Size(); width != 5 || height != 3 {
+		t.Errorf("image.Size(): expected 5, 3 but got %d, %d", width, height)
+	}
+	for _, c := range []color.RGBA{
+		{R: 0xff, A: 0xff},
+		{G: 0xff, A: 0xff},
+		{B: 0xff, A: 0xff},
+		{R: 0x10, A: 0xff},
+		{G: 0x10, A: 0xff},
+		{B: 0x10, A: 0xff},
+	} {
+		image.Set(4, 2, pixel.NewColor[pixel.RGB555](c.R, c.G, c.B))
+		c2 := image.Get(4, 2).RGBA()
+		if c2 != c {
+			t.Errorf("failed to roundtrip color: expected %v but got %v", c, c2)
+		}
+	}
+}
+
 func TestImageRGB444BE(t *testing.T) {
 	image := pixel.NewImage[pixel.RGB444BE](5, 3)
-	if width, height := image.Size(); width != 5 && height != 3 {
+	if width, height := image.Size(); width != 5 || height != 3 {
 		t.Errorf("image.Size(): expected 5, 3 but got %d, %d", width, height)
 	}
 	for _, c := range []color.RGBA{
@@ -67,7 +109,7 @@ func TestImageRGB444BE(t *testing.T) {
 
 func TestImageMonochrome(t *testing.T) {
 	image := pixel.NewImage[pixel.Monochrome](128, 64)
-	if width, height := image.Size(); width != 128 && height != 64 {
+	if width, height := image.Size(); width != 128 || height != 64 {
 		t.Errorf("image.Size(): expected 128, 64 but got %d, %d", width, height)
 	}
 	for _, expected := range []color.RGBA{

pixel/pixel.go

@@ -161,9 +161,9 @@ func (c RGB555) BitsPerPixel() int {
 
 func (c RGB555) RGBA() color.RGBA {
 	color := color.RGBA{
-		R: uint8(c>>10) << 3,
-		G: uint8(c>>5) << 3,
-		B: uint8(c) << 3,
+		R: (uint8(c) & 0x1F) << 3,
+		G: (uint8(c>>5) & 0x1F) << 3,
+		B: (uint8(c>>10) & 0x1F) << 3,
 		A: 255,
 	}
 	// Correct color rounding, so that 0xff roundtrips back to 0xff.

shiftregister/shiftregister.go

@@ -2,7 +2,8 @@
 package shiftregister
 
 import (
-	"machine"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 type NumberBit int8
@@ -16,9 +17,10 @@ const (
 
 // Device holds pin number
 type Device struct {
-	latch, clock, out machine.Pin // IC wiring
-	bits              NumberBit   // Pin number
-	mask              uint32      // keep all pins state
+	latch, clock, out pin.OutputFunc // IC wiring
+	config            func()
+	bits              NumberBit // Pin number
+	mask              uint32    // keep all pins state
 }
 
 // ShiftPin is the implementation of the ShiftPin interface.
@@ -29,20 +31,25 @@ type ShiftPin struct {
 }
 
 // New returns a new shift output register device
-func New(Bits NumberBit, Latch, Clock, Out machine.Pin) *Device {
+func New(Bits NumberBit, Latch, Clock, Out pin.Output) *Device {
 	return &Device{
-		latch: Latch,
-		clock: Clock,
-		out:   Out,
+		latch: Latch.Set,
+		clock: Clock.Set,
+		out:   Out.Set,
 		bits:  Bits,
+		config: func() {
+			legacy.ConfigurePinOut(Latch)
+			legacy.ConfigurePinOut(Clock)
+			legacy.ConfigurePinOut(Out)
+		},
 	}
 }
 
 // Configure set hardware configuration
 func (d *Device) Configure() {
-	d.latch.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.clock.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.out.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	if d.config == nil {
+		panic(legacy.ErrConfigBeforeInstantiated)
+	}
 	d.latch.High()
 }
 
@@ -53,7 +60,7 @@ func (d *Device) WriteMask(mask uint32) {
 	d.latch.Low()
 	for i := 0; i < int(d.bits); i++ {
 		d.clock.Low()
-		d.out.Set(mask&1 != 0)
+		d.out(mask&1 != 0)
 		mask = mask >> 1
 		d.clock.High()
 	}

si5351/registers.go

@@ -0,0 +1,64 @@
+package si5351
+
+// The I2C address which this device listens to.
+const AddressDefault = 0x60     // Assumes ADDR pin is low
+const AddressAlternative = 0x61 // Assumes ADDR pin is high
+
+const (
+	OUTPUT_ENABLE_CONTROL = 3
+
+	CLK0_CONTROL = 16
+	CLK1_CONTROL = 17
+	CLK2_CONTROL = 18
+	CLK3_CONTROL = 19
+	CLK4_CONTROL = 20
+	CLK5_CONTROL = 21
+	CLK6_CONTROL = 22
+	CLK7_CONTROL = 23
+
+	MULTISYNTH0_PARAMETERS_1 = 42
+	MULTISYNTH0_PARAMETERS_3 = 44
+	MULTISYNTH1_PARAMETERS_1 = 50
+	MULTISYNTH1_PARAMETERS_3 = 52
+	MULTISYNTH2_PARAMETERS_1 = 58
+	MULTISYNTH2_PARAMETERS_3 = 60
+
+	SPREAD_SPECTRUM_PARAMETERS = 149
+
+	PLL_RESET = 177
+
+	CRYSTAL_INTERNAL_LOAD_CAPACITANCE = 183
+)
+
+const (
+	CRYSTAL_LOAD_6PF  = (1 << 6)
+	CRYSTAL_LOAD_8PF  = (2 << 6)
+	CRYSTAL_LOAD_10PF = (3 << 6)
+)
+
+const (
+	CRYSTAL_FREQ_25MHZ = 25000000
+	CRYSTAL_FREQ_27MHZ = 27000000
+)
+
+const (
+	PLL_A = iota
+	PLL_B
+)
+
+const (
+	R_DIV_1 = iota
+	R_DIV_2
+	R_DIV_4
+	R_DIV_8
+	R_DIV_16
+	R_DIV_32
+	R_DIV_64
+	R_DIV_128
+)
+
+const (
+	MULTISYNTH_DIV_4 = 4
+	MULTISYNTH_DIV_6 = 6
+	MULTISYNTH_DIV_8 = 8
+)

si5351/si5351.go

@@ -0,0 +1,448 @@
+package si5351
+
+import (
+	"encoding/binary"
+	"errors"
+	"fmt"
+	"math"
+
+	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/regmap"
+)
+
+// Device wraps an I2C connection to a SI5351 device.
+type Device struct {
+	bus     drivers.I2C
+	Address uint8
+
+	rw             regmap.Device8I2C
+	initialised    bool
+	crystalFreq    uint32
+	crystalLoad    uint8
+	pllaConfigured bool
+	pllaFreq       uint32
+	pllbConfigured bool
+	pllbFreq       uint32
+	lastRdivValue  [3]uint8
+}
+
+var ErrNotInitialised = errors.New("Si5351 not initialised")
+var ErrInvalidParameter = errors.New("Si5351 invalid parameter")
+
+// New creates a new SI5351 connection. The I2C bus must already be configured.
+//
+// This function only creates the Device object, it does not touch the device.
+func New(bus drivers.I2C) Device {
+	rw := regmap.Device8I2C{}
+	rw.SetBus(bus, AddressDefault, binary.BigEndian)
+
+	return Device{
+		bus:         bus,
+		rw:          rw,
+		Address:     AddressDefault,
+		crystalFreq: CRYSTAL_FREQ_25MHZ,
+		crystalLoad: CRYSTAL_LOAD_10PF,
+	}
+}
+
+// Configure sets up the device for communication
+// TODO error handling
+func (d *Device) Configure() error {
+	// // Disable all outputs setting CLKx_DIS high
+	d.rw.Write8(OUTPUT_ENABLE_CONTROL, 0xFF)
+
+	// Set the load capacitance for the XTAL
+	d.rw.Write8(CRYSTAL_INTERNAL_LOAD_CAPACITANCE, d.crystalLoad)
+
+	// Power down all output drivers
+	buf := []byte{CLK0_CONTROL, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80}
+	d.bus.Tx(uint16(d.Address), buf, nil)
+
+	// Disable spread spectrum output.
+	if err := d.DisableSpreadSpectrum(); err != nil {
+		return err
+	}
+
+	d.initialised = true
+
+	return nil
+}
+
+// Connected returns whether a device at SI5351 address has been found.
+func (d *Device) Connected() (bool, error) {
+	if err := d.bus.Tx(uint16(d.Address), []byte{}, []byte{0}); err != nil {
+		return false, err
+	}
+	return true, nil
+}
+
+// EnableSpreadSpectrum enables spread spectrum modulation to reduce EMI.
+func (d *Device) EnableSpreadSpectrum() error {
+	data, err := d.rw.Read8(SPREAD_SPECTRUM_PARAMETERS)
+	if err != nil {
+		return err
+	}
+
+	data |= 0x80
+	return d.rw.Write8(SPREAD_SPECTRUM_PARAMETERS, data)
+}
+
+func (d *Device) DisableSpreadSpectrum() error {
+	data, err := d.rw.Read8(SPREAD_SPECTRUM_PARAMETERS)
+	if err != nil {
+		return err
+	}
+
+	data &^= 0x80
+	return d.rw.Write8(SPREAD_SPECTRUM_PARAMETERS, data)
+}
+
+func (d *Device) OutputEnable(output uint8, enable bool) error {
+	if !d.initialised {
+		return ErrNotInitialised
+	}
+
+	// Read the current value of the OUTPUT_ENABLE_CONTROL register
+	regVal, err := d.rw.Read8(OUTPUT_ENABLE_CONTROL)
+	if err != nil {
+		return err
+	}
+
+	// Modify regVal based on clk and enable
+	if enable {
+		regVal &= ^(1 << output)
+	} else {
+		regVal |= (1 << output)
+	}
+
+	// Write the modified value back to the OUTPUT_ENABLE_CONTROL register
+	return d.rw.Write8(OUTPUT_ENABLE_CONTROL, regVal)
+}
+
+func (d *Device) EnableOutputs() error {
+	if !d.initialised {
+		return ErrNotInitialised
+	}
+
+	return d.rw.Write8(OUTPUT_ENABLE_CONTROL, 0x00)
+}
+
+func (d *Device) DisableOutputs() error {
+	if !d.initialised {
+		return ErrNotInitialised
+	}
+	return d.rw.Write8(OUTPUT_ENABLE_CONTROL, 0xFF)
+}
+
+// ConfigurePLL sets the multiplier for the specified PLL
+// pll   The PLL to configure, which must be one of the following:
+// - PLL_A
+// - PLL_B
+//
+// mult  The PLL integer multiplier (must be between 15 and 90)
+//
+// num   The 20-bit numerator for fractional output (0..1,048,575).
+// Set this to '0' for integer output.
+//
+// denom The 20-bit denominator for fractional output (1..1,048,575).
+// Set this to '1' or higher to avoid divider by zero errors.
+//
+// PLL Configuration
+// fVCO is the PLL output, and must be between 600..900MHz, where:
+//
+// fVCO = fXTAL * (a+(b/c))
+//
+// fXTAL = the crystal input frequency
+// a     = an integer between 15 and 90
+// b     = the fractional numerator (0..1,048,575)
+// c     = the fractional denominator (1..1,048,575)
+//
+// NOTE: Try to use integers whenever possible to avoid clock jitter
+// (only use the a part, setting b to '0' and c to '1').
+//
+// See: http://www.silabs.com/Support%20Documents/TechnicalDocs/AN619.pdf
+func (d *Device) ConfigurePLL(pll uint8, mult uint8, num uint32, denom uint32) error {
+	// Basic validation
+	if !d.initialised {
+		return ErrNotInitialised
+	}
+	// mult = 15..90
+	if !((mult > 14) && (mult < 91)) {
+		return ErrInvalidParameter
+	}
+	// Avoid divide by zero
+	if !(denom > 0) {
+		return ErrInvalidParameter
+	}
+	// 20-bit limit
+	if !(num <= 0xFFFFF) {
+		return ErrInvalidParameter
+	}
+	// 20-bit limit
+	if !(denom <= 0xFFFFF) {
+		return ErrInvalidParameter
+	}
+
+	// PLL Multiplier Equations
+	//
+	// P1 register is an 18-bit value using following formula:
+	//
+	// 	P1[17:0] = 128 * mult + floor(128*(num/denom)) - 512
+	//
+	// P2 register is a 20-bit value using the following formula:
+	//
+	// 	P2[19:0] = 128 * num - denom * floor(128*(num/denom))
+	//
+	// P3 register is a 20-bit value using the following formula:
+	//
+	// 	P3[19:0] = denom
+	//
+
+	// Set PLL config registers
+	var p1, p2, p3 uint32
+	if num == 0 {
+		// Integer mode
+		p1 = 128*uint32(mult) - 512
+		p2 = num
+		p3 = denom
+	} else {
+		// Fractional mode
+		p1 = uint32(128*float64(mult) + math.Floor(128*(float64(num)/float64(denom))) - 512)
+		p2 = uint32(128*float64(num) - float64(denom)*math.Floor(128*(float64(num)/float64(denom))))
+		p3 = denom
+	}
+
+	// Get the appropriate starting point for the PLL registers
+	baseaddr := uint8(26)
+	if pll == PLL_B {
+		baseaddr = 34
+	}
+
+	// The datasheet is a nightmare of typos and inconsistencies here!
+	data := [8]byte{}
+	data[0] = uint8((p3 & 0x0000FF00) >> 8)
+	data[1] = uint8(p3 & 0x000000FF)
+	data[2] = uint8((p1 & 0x00030000) >> 16)
+	data[3] = uint8((p1 & 0x0000FF00) >> 8)
+	data[4] = uint8(p1 & 0x000000FF)
+	data[5] = uint8(((p3 & 0x000F0000) >> 12) | ((p2 & 0x000F0000) >> 16))
+	data[6] = uint8((p2 & 0x0000FF00) >> 8)
+	data[7] = uint8(p2 & 0x000000FF)
+	if err := d.bus.Tx(uint16(baseaddr), data[:], nil); err != nil {
+		return err
+	}
+
+	// Reset both PLLs
+	if err := d.rw.Write8(PLL_RESET, (1<<7)|(1<<5)); err != nil {
+		return err
+	}
+
+	// Store the frequency settings for use with the Multisynth helper
+	fvco := float64(d.crystalFreq) * (float64(mult) + (float64(num) / float64(denom)))
+	if pll == PLL_A {
+		d.pllaConfigured = true
+		d.pllaFreq = uint32(math.Floor(fvco))
+	} else {
+		d.pllbConfigured = true
+		d.pllbFreq = uint32(math.Floor(fvco))
+	}
+	return nil
+}
+
+// ConfigureMultisynth divider, which determines the
+// output clock frequency based on the specified PLL input.
+//
+// output    The output channel to use (0..2)
+//
+// pll       The PLL input source to use, which must be one of:
+//   - PLL_A
+//   - PLL_B
+//
+// div       The integer divider for the Multisynth output.
+//
+//	If pure integer values are used, this value must be one of:
+//	- MULTISYNTH_DIV_4
+//	- MULTISYNTH_DIV_6
+//	- MULTISYNTH_DIV_8
+//	If fractional output is used, this value must be between 8 and 900.
+//
+// num       The 20-bit numerator for fractional output (0..1,048,575).
+//
+//	Set this to '0' for integer output.
+//
+// denom     The 20-bit denominator for fractional output (1..1,048,575).
+//
+//	Set this to '1' or higher to avoid divide by zero errors.
+//
+// # Output Clock Configuration
+//
+// The multisynth dividers are applied to the specified PLL output,
+// and are used to reduce the PLL output to a valid range (500kHz
+// to 160MHz). The relationship can be seen in this formula, where
+// fVCO is the PLL output frequency and MSx is the multisynth divider:
+//
+// fOUT = fVCO / MSx
+//
+// Valid multisynth dividers are 4, 6, or 8 when using integers,
+// or any fractional values between 8 + 1/1,048,575 and 900 + 0/1
+// The following formula is used for the fractional mode divider:
+//
+// a + b / c
+//
+// a = The integer value, which must be 4, 6 or 8 in integer mode (MSx_INT=1) or 8..900 in fractional mode (MSx_INT=0).
+// b = The fractional numerator (0..1,048,575)
+// c = The fractional denominator (1..1,048,575)
+//
+// NOTE: Try to use integers whenever possible to avoid clock jitter
+// NOTE: For output frequencies > 150MHz, you must set the divider
+//
+//	to 4 and adjust to PLL to generate the frequency (for example
+//	a PLL of 640 to generate a 160MHz output clock). This is not
+//	yet supported in the driver, which limits frequencies to 500kHz .. 150MHz.
+//
+// NOTE: For frequencies below 500kHz (down to 8kHz) Rx_DIV must be
+//
+//	used, but this isn't currently implemented in the driver.
+func (d *Device) ConfigureMultisynth(output uint8, pll uint8, div uint32, num uint32, denom uint32) error {
+	// Basic validation
+	if !d.initialised {
+		return ErrNotInitialised
+	}
+	// Channel range
+	if !(output < 3) {
+		return fmt.Errorf("output channel must be between 0 and 2")
+	}
+	// Divider integer value
+	if !((div > 3) && (div < 2049)) {
+		return ErrInvalidParameter
+	}
+	// Avoid divide by zero
+	if !(denom > 0) {
+		return ErrInvalidParameter
+	}
+	// 20-bit limit
+	if !(num <= 0xFFFFF) {
+		return ErrInvalidParameter
+	}
+	// 20-bit limit
+	if !(denom <= 0xFFFFF) {
+		return ErrInvalidParameter
+	}
+
+	// Make sure the requested PLL has been initialised
+	if pll == PLL_A && !d.pllaConfigured {
+		return ErrInvalidParameter
+	}
+	if pll == PLL_B && !d.pllbConfigured {
+		return ErrInvalidParameter
+	}
+
+	// Output Multisynth Divider Equations
+	//
+	// where: a = div, b = num and c = denom
+	//
+	// P1 register is an 18-bit value using following formula:
+	//
+	//  P1[17:0] = 128 * a + floor(128*(b/c)) - 512
+	//
+	// P2 register is a 20-bit value using the following formula:
+	//
+	//  P2[19:0] = 128 * b - c * floor(128*(b/c))
+	//
+	// P3 register is a 20-bit value using the following formula:
+	//
+	//  P3[19:0] = c
+	//
+
+	// Set PLL config registers
+	var p1, p2, p3 uint32
+	if num == 0 {
+		// Integer mode
+		p1 = 128*div - 512
+		p2 = 0
+		p3 = denom
+	} else if denom == 1 {
+		// Fractional mode, simplified calculations
+		p1 = 128*div + 128*num - 512
+		p2 = 128*num - 128
+		p3 = 1
+	} else {
+		// Fractional mode
+		p1 = uint32(128*float64(div) + math.Floor(128*(float64(num)/float64(denom))) - 512)
+		p2 = uint32(128*float64(num) - float64(denom)*math.Floor(128*(float64(num)/float64(denom))))
+		p3 = denom
+	}
+
+	// Get the appropriate starting point for the PLL registers
+	baseaddr := uint8(0)
+	switch output {
+	case 0:
+		baseaddr = MULTISYNTH0_PARAMETERS_1
+	case 1:
+		baseaddr = MULTISYNTH1_PARAMETERS_1
+	case 2:
+		baseaddr = MULTISYNTH2_PARAMETERS_1
+	}
+
+	// Set the MSx config registers
+	data := [8]byte{}
+	data[0] = uint8((p3 & 0xFF00) >> 8)
+	data[1] = uint8(p3 & 0xFF)
+	data[2] = uint8(((p1 & 0x30000) >> 16)) | d.lastRdivValue[output]
+	data[3] = uint8((p1 & 0xFF00) >> 8)
+	data[4] = uint8(p1 & 0xFF)
+	data[5] = uint8(((p3 & 0xF0000) >> 12) | ((p2 & 0xF0000) >> 16))
+	data[6] = uint8((p2 & 0xFF00) >> 8)
+	data[7] = uint8(p2 & 0xFF)
+	if err := d.bus.Tx(uint16(baseaddr), data[:], nil); err != nil {
+		return err
+	}
+
+	// Configure the clk control and enable the output
+	// TODO: Check if the clk control byte needs to be updated.
+	clkControlReg := uint8(0x0F) // 8mA drive strength, MS0 as CLK0 source, Clock not inverted, powered up
+	if pll == PLL_B {
+		clkControlReg |= (1 << 5) // Uses PLLB
+	}
+	if num == 0 {
+		clkControlReg |= (1 << 6) // Integer mode
+	}
+
+	var register uint8
+	switch output {
+	case 0:
+		register = CLK0_CONTROL
+	case 1:
+		register = CLK1_CONTROL
+	case 2:
+		register = CLK2_CONTROL
+	}
+
+	return d.rw.Write8(register, clkControlReg)
+}
+
+func (d *Device) ConfigureRdiv(output uint8, div uint8) error {
+	// Channel range
+	if !(output < 3) {
+		return ErrInvalidParameter
+	}
+
+	var register uint8
+	switch output {
+	case 0:
+		register = MULTISYNTH0_PARAMETERS_3
+	case 1:
+		register = MULTISYNTH1_PARAMETERS_3
+	case 2:
+		register = MULTISYNTH2_PARAMETERS_3
+	}
+
+	data, err := d.rw.Read8(register)
+	if err != nil {
+		return err
+	}
+
+	d.lastRdivValue[output] = (div & 0x07) << 4
+	data = (data & 0x0F) | d.lastRdivValue[output]
+	return d.rw.Write8(register, data)
+}

smoketest.sh

@@ -144,6 +144,7 @@ tinygo build -size short -o ./build/test.hex -target=pico ./examples/tmc5160/mai
 tinygo build -size short -o ./build/test.uf2 -target=nicenano ./examples/sharpmem/main.go
 tinygo build -size short -o ./build/test.hex -target=feather-nrf52840 ./examples/max6675/main.go
 tinygo build -size short -o ./build/test.hex -target=pico ./examples/ens160/main.go
+tinygo build -size short -o ./build/test.hex -target=pico ./examples/si5351/main.go
 # network examples (espat)
 tinygo build -size short -o ./build/test.hex -target=challenger-rp2040 ./examples/net/ntpclient/
 # network examples (wifinina)

ssd1289/pinbus.go

@@ -1,3 +1,5 @@
+//go:build tinygo
+
 package ssd1289
 
 import "machine"

ssd1289/ssd1289.go

@@ -7,6 +7,9 @@ import (
 	"image/color"
 	"machine"
 	"time"
+
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 type Bus interface {
@@ -14,10 +17,10 @@ type Bus interface {
 }
 
 type Device struct {
-	rs  machine.Pin
-	wr  machine.Pin
-	cs  machine.Pin
-	rst machine.Pin
+	rs  pin.OutputFunc
+	wr  pin.OutputFunc
+	cs  pin.OutputFunc
+	rst pin.OutputFunc
 	bus Bus
 }
 
@@ -26,21 +29,20 @@ const height = int16(320)
 
 func New(rs machine.Pin, wr machine.Pin, cs machine.Pin, rst machine.Pin, bus Bus) Device {
 	d := Device{
-		rs:  rs,
-		wr:  wr,
-		cs:  cs,
-		rst: rst,
+		rs:  rs.Set,
+		wr:  wr.Set,
+		cs:  cs.Set,
+		rst: rst.Set,
 		bus: bus,
 	}
+	legacy.ConfigurePinOut(rs)
+	legacy.ConfigurePinOut(wr)
+	legacy.ConfigurePinOut(cs)
+	legacy.ConfigurePinOut(rst)
 
-	rs.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	wr.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	cs.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	rst.Configure(machine.PinConfig{Mode: machine.PinOutput})
-
-	cs.High()
-	rst.High()
-	wr.High()
+	cs.Set(true)
+	rst.Set(true)
+	wr.Set(true)
 
 	return d
 }

ssd1331/ssd1331.go

@@ -5,12 +5,13 @@ package ssd1331 // import "tinygo.org/x/drivers/ssd1331"
 
 import (
 	"image/color"
-	"machine"
 
 	"errors"
 	"time"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 type Model uint8
@@ -19,9 +20,9 @@ type Rotation uint8
 // Device wraps an SPI connection.
 type Device struct {
 	bus         drivers.SPI
-	dcPin       machine.Pin
-	resetPin    machine.Pin
-	csPin       machine.Pin
+	dcPin       pin.OutputFunc
+	resetPin    pin.OutputFunc
+	csPin       pin.OutputFunc
 	width       int16
 	height      int16
 	batchLength int16
@@ -36,15 +37,15 @@ type Config struct {
 }
 
 // New creates a new SSD1331 connection. The SPI wire must already be configured.
-func New(bus drivers.SPI, resetPin, dcPin, csPin machine.Pin) Device {
-	dcPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	resetPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	csPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
+func New(bus drivers.SPI, resetPin, dcPin, csPin pin.Output) Device {
+	legacy.ConfigurePinOut(dcPin)
+	legacy.ConfigurePinOut(resetPin)
+	legacy.ConfigurePinOut(csPin)
 	return Device{
 		bus:      bus,
-		dcPin:    dcPin,
-		resetPin: resetPin,
-		csPin:    csPin,
+		dcPin:    dcPin.Set,
+		resetPin: resetPin.Set,
+		csPin:    csPin.Set,
 	}
 }
 
@@ -251,7 +252,7 @@ func (d *Device) Data(data uint8) {
 
 // Tx sends data to the display
 func (d *Device) Tx(data []byte, isCommand bool) {
-	d.dcPin.Set(!isCommand)
+	d.dcPin(!isCommand)
 	d.bus.Tx(data, nil)
 }
 

ssd1351/ssd1351.go

@@ -6,10 +6,11 @@ package ssd1351 // import "tinygo.org/x/drivers/ssd1351"
 import (
 	"errors"
 	"image/color"
-	"machine"
 	"time"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 var (
@@ -19,17 +20,18 @@ var (
 
 // Device wraps an SPI connection.
 type Device struct {
-	bus          drivers.SPI
-	dcPin        machine.Pin
-	resetPin     machine.Pin
-	csPin        machine.Pin
-	enPin        machine.Pin
-	rwPin        machine.Pin
-	width        int16
-	height       int16
-	rowOffset    int16
-	columnOffset int16
-	bufferLength int16
+	bus           drivers.SPI
+	dcPin         pin.OutputFunc
+	resetPin      pin.OutputFunc
+	csPin         pin.OutputFunc
+	enPin         pin.OutputFunc
+	rwPin         pin.OutputFunc
+	configurePins func()
+	width         int16
+	height        int16
+	rowOffset     int16
+	columnOffset  int16
+	bufferLength  int16
 }
 
 // Config is the configuration for the display
@@ -41,19 +43,29 @@ type Config struct {
 }
 
 // New creates a new SSD1351 connection. The SPI wire must already be configured.
-func New(bus drivers.SPI, resetPin, dcPin, csPin, enPin, rwPin machine.Pin) Device {
+func New(bus drivers.SPI, resetPin, dcPin, csPin, enPin, rwPin pin.Output) Device {
 	return Device{
 		bus:      bus,
-		dcPin:    dcPin,
-		resetPin: resetPin,
-		csPin:    csPin,
-		enPin:    enPin,
-		rwPin:    rwPin,
+		dcPin:    dcPin.Set,
+		resetPin: resetPin.Set,
+		csPin:    csPin.Set,
+		enPin:    enPin.Set,
+		rwPin:    rwPin.Set,
+		configurePins: func() {
+			legacy.ConfigurePinOut(dcPin)
+			legacy.ConfigurePinOut(resetPin)
+			legacy.ConfigurePinOut(csPin)
+			legacy.ConfigurePinOut(enPin)
+			legacy.ConfigurePinOut(rwPin)
+		},
 	}
 }
 
 // Configure initializes the display with default configuration
 func (d *Device) Configure(cfg Config) {
+	if d.configurePins == nil {
+		panic(legacy.ErrConfigBeforeInstantiated)
+	}
 	if cfg.Width == 0 {
 		cfg.Width = 128
 	}
@@ -73,11 +85,7 @@ func (d *Device) Configure(cfg Config) {
 	}
 
 	// configure GPIO pins
-	d.dcPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.resetPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.csPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.enPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.rwPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	d.configurePins()
 
 	// reset the device
 	d.resetPin.High()
@@ -278,7 +286,7 @@ func (d *Device) Data(data uint8) {
 
 // Tx sends data to the display
 func (d *Device) Tx(data []byte, isCommand bool) {
-	d.dcPin.Set(!isCommand)
+	d.dcPin(!isCommand)
 	d.csPin.Low()
 	d.bus.Tx(data, nil)
 	d.csPin.High()

st7735/st7735.go

@@ -5,12 +5,13 @@ package st7735 // import "tinygo.org/x/drivers/st7735"
 
 import (
 	"image/color"
-	"machine"
 	"time"
 
 	"errors"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 	"tinygo.org/x/drivers/pixel"
 )
 
@@ -39,10 +40,10 @@ type Device = DeviceOf[pixel.RGB565BE]
 // formats.
 type DeviceOf[T Color] struct {
 	bus          drivers.SPI
-	dcPin        machine.Pin
-	resetPin     machine.Pin
-	csPin        machine.Pin
-	blPin        machine.Pin
+	dcPin        pin.OutputFunc
+	resetPin     pin.OutputFunc
+	csPin        pin.OutputFunc
+	blPin        pin.OutputFunc
 	width        int16
 	height       int16
 	columnOffset int16
@@ -65,23 +66,23 @@ type Config struct {
 }
 
 // New creates a new ST7735 connection. The SPI wire must already be configured.
-func New(bus drivers.SPI, resetPin, dcPin, csPin, blPin machine.Pin) Device {
+func New(bus drivers.SPI, resetPin, dcPin, csPin, blPin pin.Output) Device {
 	return NewOf[pixel.RGB565BE](bus, resetPin, dcPin, csPin, blPin)
 }
 
 // NewOf creates a new ST7735 connection with a particular pixel format. The SPI
 // wire must already be configured.
-func NewOf[T Color](bus drivers.SPI, resetPin, dcPin, csPin, blPin machine.Pin) DeviceOf[T] {
-	dcPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	resetPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	csPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	blPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
+func NewOf[T Color](bus drivers.SPI, resetPin, dcPin, csPin, blPin pin.Output) DeviceOf[T] {
+	legacy.ConfigurePinOut(dcPin)
+	legacy.ConfigurePinOut(resetPin)
+	legacy.ConfigurePinOut(csPin)
+	legacy.ConfigurePinOut(blPin)
 	return DeviceOf[T]{
 		bus:      bus,
-		dcPin:    dcPin,
-		resetPin: resetPin,
-		csPin:    csPin,
-		blPin:    blPin,
+		dcPin:    dcPin.Set,
+		resetPin: resetPin.Set,
+		csPin:    csPin.Set,
+		blPin:    blPin.Set,
 	}
 }
 
@@ -423,7 +424,7 @@ func (d *DeviceOf[T]) Data(data uint8) {
 
 // Tx sends data to the display
 func (d *DeviceOf[T]) Tx(data []byte, isCommand bool) {
-	d.dcPin.Set(!isCommand)
+	d.dcPin(!isCommand)
 	d.bus.Tx(data, nil)
 }
 

st7789/st7789.go

@@ -7,13 +7,14 @@ package st7789 // import "tinygo.org/x/drivers/st7789"
 
 import (
 	"image/color"
-	"machine"
 	"math"
 	"time"
 
 	"errors"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 	"tinygo.org/x/drivers/pixel"
 )
 
@@ -46,10 +47,10 @@ type Device = DeviceOf[pixel.RGB565BE]
 // formats.
 type DeviceOf[T Color] struct {
 	bus             drivers.SPI
-	dcPin           machine.Pin
-	resetPin        machine.Pin
-	csPin           machine.Pin
-	blPin           machine.Pin
+	dcPin           pin.OutputFunc
+	resetPin        pin.OutputFunc
+	csPin           pin.OutputFunc
+	blPin           pin.OutputFunc
 	width           int16
 	height          int16
 	columnOffsetCfg int16
@@ -83,23 +84,27 @@ type Config struct {
 }
 
 // New creates a new ST7789 connection. The SPI wire must already be configured.
-func New(bus drivers.SPI, resetPin, dcPin, csPin, blPin machine.Pin) Device {
+func New(bus drivers.SPI, resetPin, dcPin, csPin, blPin pin.Output) Device {
 	return NewOf[pixel.RGB565BE](bus, resetPin, dcPin, csPin, blPin)
 }
 
 // NewOf creates a new ST7789 connection with a particular pixel format. The SPI
 // wire must already be configured.
-func NewOf[T Color](bus drivers.SPI, resetPin, dcPin, csPin, blPin machine.Pin) DeviceOf[T] {
-	dcPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	resetPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	csPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	blPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
+func NewOf[T Color](bus drivers.SPI, resetPin, dcPin, csPin, blPin pin.Output) DeviceOf[T] {
+	legacy.ConfigurePinOut(dcPin)
+	legacy.ConfigurePinOut(resetPin)
+	legacy.ConfigurePinOut(csPin)
+	legacy.ConfigurePinOut(blPin)
+	var cs pin.OutputFunc
+	if !legacy.PinIsNoPin(csPin) {
+		cs = csPin.Set
+	}
 	return DeviceOf[T]{
 		bus:      bus,
-		dcPin:    dcPin,
-		resetPin: resetPin,
-		csPin:    csPin,
-		blPin:    blPin,
+		dcPin:    dcPin.Set,
+		resetPin: resetPin.Set,
+		csPin:    cs,
+		blPin:    blPin.Set,
 	}
 }
 
@@ -229,7 +234,7 @@ func (d *DeviceOf[T]) sendCommand(command uint8, data []byte) error {
 // startWrite must be called at the beginning of all exported methods to set the
 // chip select pin low.
 func (d *DeviceOf[T]) startWrite() {
-	if d.csPin != machine.NoPin {
+	if d.csPin != nil {
 		d.csPin.Low()
 	}
 }
@@ -237,7 +242,7 @@ func (d *DeviceOf[T]) startWrite() {
 // endWrite must be called at the end of all exported methods to set the chip
 // select pin high.
 func (d *DeviceOf[T]) endWrite() {
-	if d.csPin != machine.NoPin {
+	if d.csPin != nil {
 		d.csPin.High()
 	}
 }

sx127x/radiocontrol_pins.go

@@ -1,3 +1,5 @@
+//go:build tinygo
+
 package sx127x
 
 import (

sx127x/sx127x.go

@@ -6,10 +6,10 @@ package sx127x
 
 import (
 	"errors"
-	"machine"
 	"time"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/pin"
 	"tinygo.org/x/drivers/lora"
 )
 
@@ -22,7 +22,7 @@ const (
 // Device wraps an SPI connection to a SX127x device.
 type Device struct {
 	spi            drivers.SPI          // SPI bus for module communication
-	rstPin         machine.Pin          // GPIO for reset
+	rstPin         pin.OutputFunc       // GPIO for reset
 	radioEventChan chan lora.RadioEvent // Channel for Receiving events
 	loraConf       lora.Config          // Current Lora configuration
 	controller     RadioController      // to manage interactions with the radio
@@ -43,10 +43,10 @@ func (d *Device) GetRadioEventChan() chan lora.RadioEvent {
 }
 
 // New creates a new SX127x connection. The SPI bus must already be configured.
-func New(spi drivers.SPI, rstPin machine.Pin) *Device {
+func New(spi drivers.SPI, rstPin pin.Output) *Device {
 	k := Device{
 		spi:            spi,
-		rstPin:         rstPin,
+		rstPin:         rstPin.Set,
 		radioEventChan: make(chan lora.RadioEvent, RADIOEVENTCHAN_SIZE),
 		spiTxBuf:       make([]byte, SPI_BUFFER_SIZE),
 		spiRxBuf:       make([]byte, SPI_BUFFER_SIZE),

uc8151/uc8151.go

@@ -8,10 +8,11 @@ package uc8151 // import "tinygo.org/x/drivers/uc8151"
 import (
 	"errors"
 	"image/color"
-	"machine"
 	"time"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 	"tinygo.org/x/drivers/pixel"
 )
 
@@ -31,10 +32,10 @@ type Config struct {
 
 type Device struct {
 	bus                      drivers.SPI
-	cs                       machine.Pin
-	dc                       machine.Pin
-	rst                      machine.Pin
-	busy                     machine.Pin
+	cs                       pin.OutputFunc
+	dc                       pin.OutputFunc
+	rst                      pin.OutputFunc
+	isBusy                   pin.InputFunc
 	width                    int16
 	height                   int16
 	buffer                   []uint8
@@ -49,17 +50,17 @@ type Device struct {
 type Speed uint8
 
 // New returns a new uc8151 driver. Pass in a fully configured SPI bus.
-func New(bus drivers.SPI, csPin, dcPin, rstPin, busyPin machine.Pin) Device {
-	csPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	dcPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	rstPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	busyPin.Configure(machine.PinConfig{Mode: machine.PinInput})
+func New(bus drivers.SPI, csPin, dcPin, rstPin pin.Output, busyPin pin.Input) Device {
+	legacy.ConfigurePinOut(csPin)
+	legacy.ConfigurePinOut(dcPin)
+	legacy.ConfigurePinOut(rstPin)
+	legacy.ConfigurePinInput(busyPin)
 	return Device{
-		bus:  bus,
-		cs:   csPin,
-		dc:   dcPin,
-		rst:  rstPin,
-		busy: busyPin,
+		bus:    bus,
+		cs:     csPin.Set,
+		dc:     dcPin.Set,
+		rst:    rstPin.Set,
+		isBusy: busyPin.Get,
 	}
 }
 
@@ -313,14 +314,14 @@ func (d *Device) ClearDisplay() {
 
 // WaitUntilIdle waits until the display is ready
 func (d *Device) WaitUntilIdle() {
-	for !d.busy.Get() {
+	for !d.isBusy() {
 		time.Sleep(10 * time.Millisecond)
 	}
 }
 
 // IsBusy returns the busy status of the display
 func (d *Device) IsBusy() bool {
-	return d.busy.Get()
+	return d.isBusy()
 }
 
 // ClearBuffer sets the buffer to 0xFF (white)

waveshare-epd/epd1in54/epd1in54.go

@@ -12,6 +12,9 @@ import (
 	"image/color"
 	"machine"
 	"time"
+
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 type Config struct {
@@ -22,14 +25,14 @@ type Config struct {
 }
 
 type Device struct {
-	bus  *machine.SPI
-	cs   machine.Pin
-	dc   machine.Pin
-	rst  machine.Pin
-	busy machine.Pin
-
-	buffer   []uint8
-	rotation Rotation
+	bus           *machine.SPI
+	cs            pin.OutputFunc
+	dc            pin.OutputFunc
+	rst           pin.OutputFunc
+	isBusy        pin.InputFunc
+	configurePins func()
+	buffer        []uint8
+	rotation      Rotation
 }
 
 type Rotation uint8
@@ -79,22 +82,28 @@ var partialRefresh = [159]uint8{
 }
 
 // New returns a new epd1in54 driver. Pass in a fully configured SPI bus.
-func New(bus *machine.SPI, csPin, dcPin, rstPin, busyPin machine.Pin) Device {
+func New(bus *machine.SPI, csPin, dcPin, rstPin pin.Output, busyPin pin.Input) Device {
 	return Device{
 		buffer: make([]uint8, (uint32(Width)*uint32(Height))/8),
 		bus:    bus,
-		cs:     csPin,
-		dc:     dcPin,
-		rst:    rstPin,
-		busy:   busyPin,
+		cs:     csPin.Set,
+		dc:     dcPin.Set,
+		rst:    rstPin.Set,
+		isBusy: busyPin.Get,
+		configurePins: func() {
+			legacy.ConfigurePinOut(csPin)
+			legacy.ConfigurePinOut(dcPin)
+			legacy.ConfigurePinOut(rstPin)
+			legacy.ConfigurePinInput(busyPin)
+		},
 	}
 }
 
 func (d *Device) LDirInit(cfg Config) {
-	d.cs.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.rst.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.dc.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.busy.Configure(machine.PinConfig{Mode: machine.PinInput})
+	if d.configurePins == nil {
+		panic(legacy.ErrConfigBeforeInstantiated)
+	}
+	d.configurePins()
 
 	d.bus.Configure(machine.SPIConfig{
 		Frequency: 2000000,
@@ -150,10 +159,10 @@ func (d *Device) LDirInit(cfg Config) {
 }
 
 func (d *Device) HDirInit(cfg Config) {
-	d.cs.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.rst.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.dc.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.busy.Configure(machine.PinConfig{Mode: machine.PinInput})
+	if d.configurePins == nil {
+		panic(legacy.ErrConfigBeforeInstantiated)
+	}
+	d.configurePins()
 
 	d.bus.Configure(machine.SPIConfig{
 		Frequency: 2000000,
@@ -369,7 +378,7 @@ func (d *Device) Clear() {
 
 // WaitUntilIdle waits until the display is ready
 func (d *Device) WaitUntilIdle() {
-	for d.busy.Get() {
+	for d.isBusy() {
 		time.Sleep(100 * time.Millisecond)
 	}
 	time.Sleep(200 * time.Millisecond)
@@ -377,7 +386,7 @@ func (d *Device) WaitUntilIdle() {
 
 // IsBusy returns the busy status of the display
 func (d *Device) IsBusy() bool {
-	return d.busy.Get()
+	return d.isBusy()
 }
 
 // ClearBuffer sets the buffer to 0xFF (white)

waveshare-epd/epd2in13/epd2in13.go

@@ -6,10 +6,11 @@ package epd2in13 // import "tinygo.org/x/drivers/waveshare-epd/epd2in13"
 import (
 	"errors"
 	"image/color"
-	"machine"
 	"time"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 type Config struct {
@@ -21,10 +22,10 @@ type Config struct {
 
 type Device struct {
 	bus          drivers.SPI
-	cs           machine.Pin
-	dc           machine.Pin
-	rst          machine.Pin
-	busy         machine.Pin
+	cs           pin.OutputFunc
+	dc           pin.OutputFunc
+	rst          pin.OutputFunc
+	isBusy       pin.InputFunc
 	logicalWidth int16
 	width        int16
 	height       int16
@@ -53,17 +54,17 @@ var lutPartialUpdate = [30]uint8{
 }
 
 // New returns a new epd2in13x driver. Pass in a fully configured SPI bus.
-func New(bus drivers.SPI, csPin, dcPin, rstPin, busyPin machine.Pin) Device {
-	csPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	dcPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	rstPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	busyPin.Configure(machine.PinConfig{Mode: machine.PinInput})
+func New(bus drivers.SPI, csPin, dcPin, rstPin pin.Output, busyPin pin.Input) Device {
+	legacy.ConfigurePinOut(csPin)
+	legacy.ConfigurePinOut(dcPin)
+	legacy.ConfigurePinOut(rstPin)
+	legacy.ConfigurePinInput(busyPin)
 	return Device{
-		bus:  bus,
-		cs:   csPin,
-		dc:   dcPin,
-		rst:  rstPin,
-		busy: busyPin,
+		bus:    bus,
+		cs:     csPin.Set,
+		dc:     dcPin.Set,
+		rst:    rstPin.Set,
+		isBusy: busyPin.Get,
 	}
 }
 
@@ -298,14 +299,14 @@ func (d *Device) setMemoryPointer(x int16, y int16) {
 
 // WaitUntilIdle waits until the display is ready
 func (d *Device) WaitUntilIdle() {
-	for d.busy.Get() {
+	for d.isBusy() {
 		time.Sleep(100 * time.Millisecond)
 	}
 }
 
 // IsBusy returns the busy status of the display
 func (d *Device) IsBusy() bool {
-	return d.busy.Get()
+	return d.isBusy()
 }
 
 // ClearBuffer sets the buffer to 0xFF (white)

waveshare-epd/epd2in13x/epd2in13x.go

@@ -6,10 +6,11 @@ package epd2in13x // import "tinygo.org/x/drivers/waveshare-epd/epd2in13x"
 import (
 	"errors"
 	"image/color"
-	"machine"
 	"time"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 type Config struct {
@@ -20,10 +21,10 @@ type Config struct {
 
 type Device struct {
 	bus          drivers.SPI
-	cs           machine.Pin
-	dc           machine.Pin
-	rst          machine.Pin
-	busy         machine.Pin
+	cs           pin.OutputFunc
+	dc           pin.OutputFunc
+	rst          pin.OutputFunc
+	isBusy       pin.InputFunc
 	width        int16
 	height       int16
 	buffer       [][]uint8
@@ -33,17 +34,17 @@ type Device struct {
 type Color uint8
 
 // New returns a new epd2in13x driver. Pass in a fully configured SPI bus.
-func New(bus drivers.SPI, csPin, dcPin, rstPin, busyPin machine.Pin) Device {
-	csPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	dcPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	rstPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	busyPin.Configure(machine.PinConfig{Mode: machine.PinInput})
+func New(bus drivers.SPI, csPin, dcPin, rstPin pin.Output, busyPin pin.Input) Device {
+	legacy.ConfigurePinOut(csPin)
+	legacy.ConfigurePinOut(dcPin)
+	legacy.ConfigurePinOut(rstPin)
+	legacy.ConfigurePinInput(busyPin)
 	return Device{
-		bus:  bus,
-		cs:   csPin,
-		dc:   dcPin,
-		rst:  rstPin,
-		busy: busyPin,
+		bus:    bus,
+		cs:     csPin.Set,
+		dc:     dcPin.Set,
+		rst:    rstPin.Set,
+		isBusy: busyPin.Get,
 	}
 }
 
@@ -277,14 +278,14 @@ func (d *Device) ClearDisplay() {
 
 // WaitUntilIdle waits until the display is ready
 func (d *Device) WaitUntilIdle() {
-	for !d.busy.Get() {
+	for !d.isBusy() {
 		time.Sleep(100 * time.Millisecond)
 	}
 }
 
 // IsBusy returns the busy status of the display
 func (d *Device) IsBusy() bool {
-	return d.busy.Get()
+	return d.isBusy()
 }
 
 // ClearBuffer sets the buffer to 0xFF (white)

waveshare-epd/epd2in66b/dev.go

@@ -5,10 +5,11 @@ package epd2in66b
 
 import (
 	"image/color"
-	"machine"
 	"time"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 const (
@@ -18,20 +19,12 @@ const (
 
 const Baudrate = 4_000_000 // 4 MHz
 
-type Config struct {
-	ResetPin      machine.Pin
-	DataPin       machine.Pin
-	ChipSelectPin machine.Pin
-	BusyPin       machine.Pin
-}
-
 type Device struct {
-	bus  drivers.SPI
-	cs   machine.Pin
-	dc   machine.Pin
-	rst  machine.Pin
-	busy machine.Pin
-
+	bus         drivers.SPI
+	cs          pin.OutputFunc
+	dc          pin.OutputFunc
+	rst         pin.OutputFunc
+	isBusy      pin.InputFunc
 	blackBuffer []byte
 	redBuffer   []byte
 }
@@ -50,18 +43,23 @@ func New(bus drivers.SPI) Device {
 	}
 }
 
+type Config struct {
+	ResetPin      pin.Output
+	DataPin       pin.Output
+	ChipSelectPin pin.Output
+	BusyPin       pin.Input
+}
+
 // Configure configures the device and its pins.
 func (d *Device) Configure(c Config) error {
-	d.cs = c.ChipSelectPin
-	d.dc = c.DataPin
-	d.rst = c.ResetPin
-	d.busy = c.BusyPin
-
-	d.cs.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.dc.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.rst.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.busy.Configure(machine.PinConfig{Mode: machine.PinInput})
-
+	d.cs = c.ChipSelectPin.Set
+	d.dc = c.DataPin.Set
+	d.rst = c.ResetPin.Set
+	d.isBusy = c.BusyPin.Get
+	legacy.ConfigurePinOut(c.ChipSelectPin)
+	legacy.ConfigurePinOut(c.DataPin)
+	legacy.ConfigurePinOut(c.ResetPin)
+	legacy.ConfigurePinInput(c.BusyPin)
 	return nil
 }
 
@@ -229,7 +227,7 @@ func (d *Device) WaitUntilIdle() {
 	// give it some time to get busy
 	time.Sleep(50 * time.Millisecond)
 
-	for d.busy.Get() { // high = busy
+	for d.isBusy() { // high = busy
 		time.Sleep(10 * time.Millisecond)
 	}
 

waveshare-epd/epd2in9/epd2in9.go

@@ -13,10 +13,11 @@ package epd2in9 // import "tinygo.org/x/drivers/waveshare-epd/epd2in9"
 
 import (
 	"image/color"
-	"machine"
 	"time"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 type Config struct {
@@ -28,10 +29,10 @@ type Config struct {
 
 type Device struct {
 	bus          drivers.SPI
-	cs           machine.Pin
-	dc           machine.Pin
-	rst          machine.Pin
-	busy         machine.Pin
+	cs           pin.OutputFunc
+	dc           pin.OutputFunc
+	rst          pin.OutputFunc
+	isBusy       pin.InputFunc
 	logicalWidth int16
 	width        int16
 	height       int16
@@ -61,17 +62,17 @@ var lutPartialUpdate = [30]uint8{
 }
 
 // New returns a new epd2in9 driver. Pass in a fully configured SPI bus.
-func New(bus drivers.SPI, csPin, dcPin, rstPin, busyPin machine.Pin) Device {
-	csPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	dcPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	rstPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	busyPin.Configure(machine.PinConfig{Mode: machine.PinInput})
+func New(bus drivers.SPI, csPin, dcPin, rstPin pin.Output, busyPin pin.Input) Device {
+	legacy.ConfigurePinOut(csPin)
+	legacy.ConfigurePinOut(dcPin)
+	legacy.ConfigurePinOut(rstPin)
+	legacy.ConfigurePinInput(busyPin)
 	return Device{
-		bus:  bus,
-		cs:   csPin,
-		dc:   dcPin,
-		rst:  rstPin,
-		busy: busyPin,
+		bus:    bus,
+		cs:     csPin.Set,
+		dc:     dcPin.Set,
+		rst:    rstPin.Set,
+		isBusy: busyPin.Get,
 	}
 }
 
@@ -245,14 +246,14 @@ func (d *Device) setMemoryPointer(x int16, y int16) {
 
 // WaitUntilIdle waits until the display is ready
 func (d *Device) WaitUntilIdle() {
-	for d.busy.Get() {
+	for d.isBusy() {
 		time.Sleep(100 * time.Millisecond)
 	}
 }
 
 // IsBusy returns the busy status of the display
 func (d *Device) IsBusy() bool {
-	return d.busy.Get()
+	return d.isBusy()
 }
 
 // ClearBuffer sets the buffer to 0xFF (white)

waveshare-epd/epd4in2/epd4in2.go

@@ -10,10 +10,11 @@ package epd4in2
 
 import (
 	"image/color"
-	"machine"
 	"time"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+	"tinygo.org/x/drivers/internal/pin"
 )
 
 type Config struct {
@@ -25,10 +26,10 @@ type Config struct {
 
 type Device struct {
 	bus          drivers.SPI
-	cs           machine.Pin
-	dc           machine.Pin
-	rst          machine.Pin
-	busy         machine.Pin
+	cs           pin.OutputFunc
+	dc           pin.OutputFunc
+	rst          pin.OutputFunc
+	isBusy       pin.InputFunc
 	logicalWidth int16
 	width        int16
 	height       int16
@@ -40,17 +41,17 @@ type Device struct {
 type Rotation uint8
 
 // New returns a new epd4in2 driver. Pass in a fully configured SPI bus.
-func New(bus drivers.SPI, csPin, dcPin, rstPin, busyPin machine.Pin) Device {
-	csPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	dcPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	rstPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	busyPin.Configure(machine.PinConfig{Mode: machine.PinInput})
+func New(bus drivers.SPI, csPin, dcPin, rstPin pin.Output, busyPin pin.Input) Device {
+	legacy.ConfigurePinOut(csPin)
+	legacy.ConfigurePinOut(dcPin)
+	legacy.ConfigurePinOut(rstPin)
+	legacy.ConfigurePinInput(busyPin)
 	return Device{
-		bus:  bus,
-		cs:   csPin,
-		dc:   dcPin,
-		rst:  rstPin,
-		busy: busyPin,
+		bus:    bus,
+		cs:     csPin.Set,
+		dc:     dcPin.Set,
+		rst:    rstPin.Set,
+		isBusy: busyPin.Get,
 	}
 }
 
@@ -311,14 +312,14 @@ func (d *Device) ClearDisplay() {
 
 // WaitUntilIdle waits until the display is ready
 func (d *Device) WaitUntilIdle() {
-	for d.busy.Get() {
+	for d.isBusy() {
 		time.Sleep(100 * time.Millisecond)
 	}
 }
 
 // IsBusy returns the busy status of the display
 func (d *Device) IsBusy() bool {
-	return d.busy.Get()
+	return d.isBusy()
 }
 
 // ClearBuffer sets the buffer to 0xFF (white)