Replace Safe functions with legacy.PinOutput

Signed-off-by: deadprogram <ron@hybridgroup.com>

CHANGELOG.md

@@ -1,3 +1,28 @@
+0.33.0
+---
+- **new devices**
+    - **ens160**
+        - Add ens160 i2c driver
+    - **lsm303dlhc**
+        - added support for LSM303DLHC e-Compass; (#783)
+    - **seesaw**
+        - add support for Adafruit Seesaw encoders
+
+- **enhancements**
+    - **ws2812**
+        - add RP2350 support
+    - **ssd1306**
+        - avoid unnecessary heap allocations (#767)
+    - **gps**
+        - allow gps init with address
+    - **lsm6ds3tr**
+        - avoid unnecessary heap allocations (#766)
+
+- **bugfixes**
+    - **gps**
+        - Fix gps time calculation (#785)
+
+
 0.32.0
 ---
 - **enhancements**

bmi160/bmi160.go

@@ -1,17 +1,17 @@
 package bmi160
 
 import (
-	"machine"
 	"time"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
 )
 
 // DeviceSPI is the SPI interface to a BMI160 accelerometer/gyroscope. There is
 // also an I2C interface, but it is not yet supported.
 type DeviceSPI struct {
 	// Chip select pin
-	CSB machine.Pin
+	CSB drivers.PinOutput
 
 	buf [7]byte
 
@@ -22,9 +22,9 @@ type DeviceSPI struct {
 // NewSPI returns a new device driver. The pin and SPI interface are not
 // touched, provide a fully configured SPI object and call Configure to start
 // using this device.
-func NewSPI(csb machine.Pin, spi drivers.SPI) *DeviceSPI {
+func NewSPI(csb drivers.PinOutput, spi drivers.SPI) *DeviceSPI {
 	return &DeviceSPI{
-		CSB: csb, // chip select
+		CSB: legacy.PinOutput(csb), // chip select
 		Bus: spi,
 	}
 }
@@ -33,8 +33,7 @@ func NewSPI(csb machine.Pin, spi drivers.SPI) *DeviceSPI {
 // configures the BMI160, but it does not configure the SPI interface (it is
 // assumed to be up and running).
 func (d *DeviceSPI) Configure() error {
-	d.CSB.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.CSB.High()
+	d.CSB.Set(true)
 
 	// The datasheet recommends doing a register read from address 0x7F to get
 	// SPI communication going:
@@ -86,9 +85,9 @@ func (d *DeviceSPI) ReadTemperature() (temperature int32, err error) {
 	data[0] = 0x80 | reg_TEMPERATURE_0
 	data[1] = 0
 	data[2] = 0
-	d.CSB.Low()
+	d.CSB.Set(false)
 	err = d.Bus.Tx(data, data)
-	d.CSB.High()
+	d.CSB.Set(true)
 	if err != nil {
 		return
 	}
@@ -123,9 +122,9 @@ func (d *DeviceSPI) ReadAcceleration() (x int32, y int32, z int32, err error) {
 	for i := 1; i < len(data); i++ {
 		data[i] = 0
 	}
-	d.CSB.Low()
+	d.CSB.Set(false)
 	err = d.Bus.Tx(data, data)
-	d.CSB.High()
+	d.CSB.Set(true)
 	if err != nil {
 		return
 	}
@@ -153,9 +152,9 @@ func (d *DeviceSPI) ReadRotation() (x int32, y int32, z int32, err error) {
 	for i := 1; i < len(data); i++ {
 		data[i] = 0
 	}
-	d.CSB.Low()
+	d.CSB.Set(false)
 	err = d.Bus.Tx(data, data)
-	d.CSB.High()
+	d.CSB.Set(true)
 	if err != nil {
 		return
 	}
@@ -201,9 +200,9 @@ func (d *DeviceSPI) readRegister(address uint8) uint8 {
 	data := d.buf[:2]
 	data[0] = 0x80 | address
 	data[1] = 0
-	d.CSB.Low()
+	d.CSB.Set(false)
 	d.Bus.Tx(data, data)
-	d.CSB.High()
+	d.CSB.Set(true)
 	return data[1]
 }
 
@@ -217,7 +216,7 @@ func (d *DeviceSPI) writeRegister(address, data uint8) {
 	buf[0] = address
 	buf[1] = data
 
-	d.CSB.Low()
+	d.CSB.Set(false)
 	d.Bus.Tx(buf, buf)
-	d.CSB.High()
+	d.CSB.Set(true)
 }

buzzer/buzzer.go

@@ -2,22 +2,22 @@
 package buzzer // import "tinygo.org/x/drivers/buzzer"
 
 import (
-	"machine"
-
 	"time"
+
+	"tinygo.org/x/drivers"
 )
 
 // Device wraps a GPIO connection to a buzzer.
 type Device struct {
-	pin  machine.Pin
+	set  drivers.PinSet
 	High bool
 	BPM  float64
 }
 
 // New returns a new buzzer driver given which pin to use
-func New(pin machine.Pin) Device {
+func New(pin drivers.PinOutput) Device {
 	return Device{
-		pin:  pin,
+		set:  pin.Set,
 		High: false,
 		BPM:  96.0,
 	}
@@ -25,14 +25,14 @@ func New(pin machine.Pin) Device {
 
 // On sets the buzzer to a high state.
 func (l *Device) On() (err error) {
-	l.pin.Set(true)
+	l.set(true)
 	l.High = true
 	return
 }
 
 // Off sets the buzzer to a low state.
 func (l *Device) Off() (err error) {
-	l.pin.Set(false)
+	l.set(false)
 	l.High = false
 	return
 }

dht/thermometer.go

@@ -9,9 +9,10 @@
 package dht // import "tinygo.org/x/drivers/dht"
 
 import (
-	"machine"
 	"runtime/interrupt"
 	"time"
+
+	"tinygo.org/x/drivers"
 )
 
 // DummyDevice provides a basic interface for DHT devices.
@@ -30,7 +31,7 @@ type DummyDevice interface {
 // Since taking measurements from the sensor is time consuming procedure and blocks interrupts,
 // user can avoid any hidden calls to the sensor.
 type device struct {
-	pin machine.Pin
+	pin drivers.Pin
 
 	measurements DeviceType
 	initialized  bool
@@ -93,14 +94,12 @@ func (t *device) HumidityFloat() (float32, error) {
 // Perform initialization of the communication protocol.
 // Device lowers the voltage on pin for startingLow=20ms and starts listening for response
 // Section 5.2 in [1]
-func initiateCommunication(p machine.Pin) {
+func initiateCommunication(p drivers.Pin) {
 	// Send low signal to the device
-	p.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	p.Low()
+	p.Set(false)
 	time.Sleep(startingLow)
 	// Set pin to high and wait for reply
-	p.High()
-	p.Configure(machine.PinConfig{Mode: machine.PinInput})
+	p.Set(true)
 }
 
 // Measurements returns both measurements: temperature and humidity as they sent by the device.
@@ -158,7 +157,7 @@ func (t *device) read() error {
 
 // receiveSignals counts number of low and high cycles. The execution is time critical, so the function disables
 // interrupts
-func receiveSignals(pin machine.Pin, result []counter) {
+func receiveSignals(pin drivers.PinInput, result []counter) {
 	i := uint8(0)
 	mask := interrupt.Disable()
 	defer interrupt.Restore(mask)
@@ -189,7 +188,7 @@ func (t *device) extractData(signals []counter, buf []uint8) error {
 // waitForDataTransmission waits for reply from the sensor.
 // If no reply received, returns NoSignalError.
 // For more details, see section 5.2 in [1]
-func waitForDataTransmission(p machine.Pin) error {
+func waitForDataTransmission(p drivers.PinInput) error {
 	// wait for thermometer to pull down
 	if expectChange(p, true) == timeout {
 		return NoSignalError
@@ -209,8 +208,8 @@ func waitForDataTransmission(p machine.Pin) error {
 // This device provides full control to the user.
 // It does not do any hidden measurements calls and does not check
 // for 2 seconds delay between measurements.
-func NewDummyDevice(pin machine.Pin, deviceType DeviceType) DummyDevice {
-	pin.High()
+func NewDummyDevice(pin drivers.Pin, deviceType DeviceType) DummyDevice {
+	pin.Set(true)
 	return &device{
 		pin:          pin,
 		measurements: deviceType,

dht/timesafethermometer.go

@@ -9,8 +9,9 @@
 package dht // import "tinygo.org/x/drivers/dht"
 
 import (
-	"machine"
 	"time"
+
+	"tinygo.org/x/drivers"
 )
 
 // Device interface provides main functionality of the DHTXX sensors.
@@ -124,8 +125,8 @@ func (m *managedDevice) Configure(policy UpdatePolicy) {
 
 // Constructor of the Device implementation.
 // This implementation updates data every 2 seconds during data access.
-func New(pin machine.Pin, deviceType DeviceType) Device {
-	pin.High()
+func New(pin drivers.Pin, deviceType DeviceType) Device {
+	pin.Set(true)
 	return &managedDevice{
 		t: device{
 			pin:          pin,
@@ -141,8 +142,8 @@ func New(pin machine.Pin, deviceType DeviceType) Device {
 }
 
 // Constructor of the Device implementation with given UpdatePolicy
-func NewWithPolicy(pin machine.Pin, deviceType DeviceType, updatePolicy UpdatePolicy) Device {
-	pin.High()
+func NewWithPolicy(pin drivers.Pin, deviceType DeviceType, updatePolicy UpdatePolicy) Device {
+	pin.Set(true)
 	result := &managedDevice{
 		t: device{
 			pin:          pin,

dht/util.go

@@ -3,21 +3,22 @@
 package dht // import "tinygo.org/x/drivers/dht"
 
 import (
-	"machine"
 	"time"
+
+	"tinygo.org/x/drivers"
 )
 
 // Check if the pin is disabled
-func powerUp(p machine.Pin) bool {
+func powerUp(p drivers.Pin) bool {
 	state := p.Get()
 	if !state {
-		p.High()
+		p.Set(true)
 		time.Sleep(startTimeout)
 	}
 	return state
 }
 
-func expectChange(p machine.Pin, oldState bool) counter {
+func expectChange(p drivers.PinInput, oldState bool) counter {
 	cnt := counter(0)
 	for ; p.Get() == oldState && cnt != timeout; cnt++ {
 	}

ens160/ens160.go

@@ -0,0 +1,225 @@
+// Package ens160 provides a driver for the ScioSense ENS160 digital gas sensor.
+//
+// Datasheet: https://www.sciosense.com/wp-content/uploads/2023/12/ENS160-Datasheet.pdf
+package ens160
+
+import (
+	"encoding/binary"
+	"errors"
+	"time"
+
+	"tinygo.org/x/drivers"
+)
+
+const (
+	defaultTimeout = 30 * time.Millisecond
+	shortTimeout   = 1 * time.Millisecond
+)
+
+// Conversion constants for environment data compensation.
+const (
+	kelvinOffsetMilli = 273150          // 273.15 K in milli-units
+	tempRawFactor     = 64              // As per datasheet for TEMP_IN
+	humRawFactor      = 512             // As per datasheet for RH_IN
+	milliFactor       = 1000            // For converting from milli-units
+	roundingTerm      = milliFactor / 2 // For rounding before integer division
+)
+
+// validityStrings provides human-readable descriptions for validity flags.
+var validityStrings = [...]string{
+	ValidityNormalOperation:     "normal operation",
+	ValidityWarmUpPhase:         "warm-up phase, wait ~3 minutes for valid data",
+	ValidityInitialStartUpPhase: "initial start-up phase, wait ~1 hour for valid data",
+	ValidityInvalidOutput:       "invalid output",
+}
+
+// Device wraps an I2C connection to an ENS160 device.
+type Device struct {
+	bus  drivers.I2C // I²C implementation
+	addr uint16      // 7‑bit bus address, promoted to uint16 per drivers.I2C
+
+	// shadow registers / last measurements
+	lastTvocPPB  uint16
+	lastEco2PPM  uint16
+	lastAqiUBA   uint8
+	lastValidity uint8 // Store the latest validity status
+
+	// pre‑allocated buffers
+	wbuf [5]byte // longest write: reg + 4 bytes (TEMP+RH)
+	rbuf [5]byte // longest read: DATA burst (5 bytes)
+}
+
+// New returns a new ENS160 driver.
+func New(bus drivers.I2C, addr uint16) *Device {
+	if addr == 0 {
+		addr = DefaultAddress
+	}
+	return &Device{
+		bus:          bus,
+		addr:         addr,
+		lastValidity: ValidityInvalidOutput,
+	}
+}
+
+// Connected returns whether a ENS160 has been found.
+func (d *Device) Connected() bool {
+	d.wbuf[0] = regPartID
+	err := d.bus.Tx(d.addr, d.wbuf[:1], d.rbuf[:2])
+	return err == nil && d.rbuf[0] == LowPartID && d.rbuf[1] == HighPartID
+}
+
+// Configure sets up the device for reading.
+func (d *Device) Configure() error {
+	// 1. Soft-reset. The device will automatically enter IDLE mode.
+	if err := d.write1(regOpMode, ModeReset); err != nil {
+		return err
+	}
+	time.Sleep(defaultTimeout)
+
+	// 2. Clear GPR registers, then go to STANDARD mode.
+	if err := d.write1(regCommand, cmdClrGPR); err != nil {
+		return err
+	}
+	time.Sleep(defaultTimeout)
+
+	if err := d.write1(regOpMode, ModeStandard); err != nil {
+		return err
+	}
+	time.Sleep(defaultTimeout)
+
+	return nil
+}
+
+// calculateTempRaw converts temperature from milli-degrees Celsius to the sensor's raw format.
+func calculateTempRaw(tempMilliC int32) uint16 {
+	// Clip temperature
+	const (
+		minC = -40 * 1000
+		maxC = 85 * 1000
+	)
+	if tempMilliC < minC {
+		tempMilliC = minC
+	} else if tempMilliC > maxC {
+		tempMilliC = maxC
+	}
+
+	// Integer fixed-point conversion to format required by the sensor.
+	// Formula from datasheet: T_IN = (T_ambient_C + 273.15) * 64
+	return uint16((((tempMilliC + kelvinOffsetMilli) * tempRawFactor) + roundingTerm) / milliFactor)
+}
+
+// calculateHumRaw converts relative humidity from milli-percent to the sensor's raw format.
+func calculateHumRaw(rhMilliPct int32) uint16 {
+	// Clip humidity
+	if rhMilliPct < 0 {
+		rhMilliPct = 0
+	} else if rhMilliPct > 100*1000 {
+		rhMilliPct = 100 * 1000
+	}
+
+	// Integer fixed-point conversion to format required by the sensor.
+	// Formula from datasheet: RH_IN = (RH_ambient_% * 512)
+	return uint16(((rhMilliPct * humRawFactor) + roundingTerm) / milliFactor)
+}
+
+// SetEnvDataMilli sets the ambient temperature and humidity for compensation.
+//
+// tempMilliC is the temperature in milli-degrees Celsius.
+// rhMilliPct is the relative humidity in milli-percent.
+func (d *Device) SetEnvDataMilli(tempMilliC, rhMilliPct int32) error {
+	tempRaw := calculateTempRaw(tempMilliC)
+	humRaw := calculateHumRaw(rhMilliPct)
+
+	d.wbuf[0] = regTempIn // start address (auto‑increment)
+	binary.LittleEndian.PutUint16(d.wbuf[1:3], tempRaw)
+	binary.LittleEndian.PutUint16(d.wbuf[3:5], humRaw)
+
+	return d.bus.Tx(d.addr, d.wbuf[:5], nil)
+}
+
+// Update refreshes the concentration measurements.
+func (d *Device) Update(which drivers.Measurement) error {
+	if which&drivers.Concentration == 0 {
+		return nil // nothing requested
+	}
+
+	const maxTries = 1000
+	var (
+		status   uint8
+		validity uint8
+	)
+	var gotData bool
+
+	// Poll DEVICE_STATUS until NEWDAT or timeout
+	for range maxTries {
+		var err error
+		status, err = d.read1(regStatus)
+		if err != nil {
+			return err
+		}
+		if status&statusSTATER != 0 {
+			return errors.New("ENS160: error (STATER set)")
+		}
+		validity = (status & statusValidityMask) >> statusValidityShift
+
+		if status&statusNEWDAT != 0 {
+			gotData = true
+			break // Always break when data available
+		}
+		time.Sleep(shortTimeout)
+	}
+	if !gotData {
+		return errors.New("ENS160: timeout waiting for NEWDAT")
+	}
+
+	// Burst-read data regardless of validity state
+	d.wbuf[0] = regAQI
+	if err := d.bus.Tx(d.addr, d.wbuf[:1], d.rbuf[:5]); err != nil {
+		return errors.New("ENS160: burst read failed")
+	}
+
+	d.lastAqiUBA = d.rbuf[0]
+	d.lastTvocPPB = binary.LittleEndian.Uint16(d.rbuf[1:3])
+	d.lastEco2PPM = binary.LittleEndian.Uint16(d.rbuf[3:5])
+	d.lastValidity = validity // Store the validity status
+
+	return nil
+}
+
+// TVOC returns the last total‑VOC concentration in parts‑per‑billion.
+func (d *Device) TVOC() uint16 { return d.lastTvocPPB }
+
+// ECO2 returns the last equivalent CO₂ concentration in parts‑per‑million.
+func (d *Device) ECO2() uint16 { return d.lastEco2PPM }
+
+// AQI returns the last Air‑Quality Index according to UBA (1–5).
+func (d *Device) AQI() uint8 { return d.lastAqiUBA }
+
+// Validity returns the current operating state of the sensor.
+func (d *Device) Validity() uint8 {
+	return d.lastValidity
+}
+
+// ValidityString returns a human-readable string describing the current validity status.
+func (d *Device) ValidityString() string {
+	if int(d.lastValidity) < len(validityStrings) {
+		return validityStrings[d.lastValidity]
+	}
+	return "unknown"
+}
+
+// write1 writes a single byte to a register.
+func (d *Device) write1(reg, val uint8) error {
+	d.wbuf[0] = reg
+	d.wbuf[1] = val
+	return d.bus.Tx(d.addr, d.wbuf[:2], nil)
+}
+
+// read1 reads a single byte from a register.
+func (d *Device) read1(reg uint8) (uint8, error) {
+	d.wbuf[0] = reg
+	if err := d.bus.Tx(d.addr, d.wbuf[:1], d.rbuf[:1]); err != nil {
+		return 0, err
+	}
+	return d.rbuf[0], nil
+}

ens160/ens160_test.go

@@ -0,0 +1,54 @@
+package ens160
+
+import (
+	"testing"
+)
+
+func TestCalculateTempRaw(t *testing.T) {
+	testCases := []struct {
+		name        string
+		tempMilliC  int32
+		expectedRaw uint16
+	}{
+		{"25°C", 25000, 19082},
+		{"-10.5°C", -10500, 16810},
+		{"Min temp", -40000, 14922},
+		{"Below min", -50000, 14922},
+		{"Max temp", 85000, 22922},
+		{"Above max", 90000, 22922},
+		{"Zero", 0, 17482},
+	}
+
+	for _, tc := range testCases {
+		t.Run(tc.name, func(t *testing.T) {
+			raw := calculateTempRaw(tc.tempMilliC)
+			if raw != tc.expectedRaw {
+				t.Errorf("expected %d, got %d", tc.expectedRaw, raw)
+			}
+		})
+	}
+}
+
+func TestCalculateHumRaw(t *testing.T) {
+	testCases := []struct {
+		name        string
+		rhMilliPct  int32
+		expectedRaw uint16
+	}{
+		{"50%", 50000, 25600},
+		{"0%", 0, 0},
+		{"100%", 100000, 51200},
+		{"Below 0%", -10000, 0},
+		{"Above 100%", 110000, 51200},
+		{"33.3%", 33300, 17050},
+	}
+
+	for _, tc := range testCases {
+		t.Run(tc.name, func(t *testing.T) {
+			raw := calculateHumRaw(tc.rhMilliPct)
+			if raw != tc.expectedRaw {
+				t.Errorf("expected %d, got %d", tc.expectedRaw, raw)
+			}
+		})
+	}
+}

ens160/registers.go

@@ -0,0 +1,65 @@
+package ens160
+
+// DefaultAddress is the default I2C address for the ENS160 when the ADDR pin is
+// connected to high (3.3V). When connected to low (GND), the address is 0x52.
+const DefaultAddress = 0x53
+
+// Registers
+const (
+	regPartID   = 0x00
+	regOpMode   = 0x10
+	regConfig   = 0x11
+	regCommand  = 0x12
+	regTempIn   = 0x13
+	regRhIn     = 0x15
+	regStatus   = 0x20
+	regAQI      = 0x21
+	regTVOC     = 0x22
+	regECO2     = 0x24
+	regDataT    = 0x30
+	regDataRH   = 0x32
+	regMISR     = 0x38
+	regGPRWrite = 0x40
+	regGPRRead  = 0x48
+)
+
+// Operating modes
+const (
+	ModeDeepSleep = 0x00
+	ModeIdle      = 0x01
+	ModeStandard  = 0x02
+	ModeReset     = 0xF0
+)
+
+// Status register bits
+const (
+	statusSTATAS = 1 << 7
+	statusSTATER = 1 << 6
+
+	statusValidityMask  = 0x0C
+	statusValidityShift = 2
+
+	statusNEWDAT = 1 << 1
+	statusNEWGPR = 1 << 0
+)
+
+// Validity flags
+const (
+	ValidityNormalOperation     = 0x00
+	ValidityWarmUpPhase         = 0x01 // need ~3 minutes until valid data
+	ValidityInitialStartUpPhase = 0x02 // need ~1 hour until valid data
+	ValidityInvalidOutput       = 0x03
+)
+
+// Commands
+const (
+	cmdNOP       = 0x00
+	cmdGetAppVer = 0x0E
+	cmdClrGPR    = 0xCC
+)
+
+// Part IDs
+const (
+	LowPartID  = 0x60
+	HighPartID = 0x01
+)

examples/dht/main.go

@@ -1,14 +1,18 @@
+//go:build baremetal && tinygo
+
 package main
 
 import (
 	"fmt"
 	"machine"
 	"time"
+
 	"tinygo.org/x/drivers/dht"
+	"tinygo.org/x/drivers/tinygo"
 )
 
 func main() {
-	pin := machine.D6
+	pin := tinygo.New(machine.D6)
 	dhtSensor := dht.New(pin, dht.DHT11)
 	for {
 		temp, hum, err := dhtSensor.Measurements()

examples/ens160/main.go

@@ -0,0 +1,56 @@
+// This example demonstrates ENS160 usage.
+//
+// Wiring:
+// - VCC to 3.3V, GND to ground
+// - SDA to board SDA, SCL to board SCL
+
+package main
+
+import (
+	"time"
+
+	"machine"
+
+	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/ens160"
+)
+
+func main() {
+	err := machine.I2C0.Configure(machine.I2CConfig{
+		Frequency: 400 * machine.KHz,
+	})
+	if err != nil {
+		println("Failed to configure I2C:", err)
+	}
+
+	dev := ens160.New(machine.I2C0, ens160.DefaultAddress)
+
+	connected := dev.Connected()
+	if !connected {
+		println("ENS160 not detected")
+		return
+	}
+	println("ENS160 detected")
+
+	if err := dev.Configure(); err != nil {
+		println("Failed to configure ENS160:", err)
+	}
+
+	for {
+		err := dev.Update(drivers.Concentration)
+		if err != nil {
+			println("Error reading ENS160: %v\n", err)
+			time.Sleep(5 * time.Second)
+			continue
+		}
+
+		println(
+			"AQI:", dev.AQI(),
+			"TVOC:", dev.TVOC(),
+			"eCO2:", dev.ECO2(),
+			"Validity:", dev.ValidityString(),
+		)
+
+		time.Sleep(2 * time.Second)
+	}
+}

examples/gps/i2c/main.go

@@ -10,7 +10,7 @@ import (
 func main() {
 	println("GPS I2C Example")
 	machine.I2C0.Configure(machine.I2CConfig{})
-	ublox := gps.NewI2C(machine.I2C0)
+	ublox := gps.NewI2CWithAddress(machine.I2C0, gps.UBLOX_I2C_ADDRESS)
 	parser := gps.NewParser()
 	var fix gps.Fix
 	for {

examples/hcsr04/main.go

@@ -5,10 +5,13 @@ import (
 	"time"
 
 	"tinygo.org/x/drivers/hcsr04"
+	"tinygo.org/x/drivers/tinygo"
 )
 
 func main() {
-	sensor := hcsr04.New(machine.D10, machine.D9)
+	trigger := tinygo.New(machine.D10) // automatically configures pin as output
+	echo := tinygo.New(machine.D9)     // automatically configures pin as input
+	sensor := hcsr04.New(trigger, echo)
 	sensor.Configure()
 
 	println("Ultrasonic starts")

examples/lsm303dlhc/main.go

@@ -0,0 +1,58 @@
+package main
+
+import (
+	"machine"
+	"time"
+
+	"tinygo.org/x/drivers/lsm303dlhc"
+)
+
+func main() {
+
+	// LSM303DLHC is connected to the I2C0 bus on Adafruit Feather M4 via pins: 20(SDA) and 21(SCL).
+	machine.I2C0.Configure(machine.I2CConfig{})
+
+	sensor := lsm303dlhc.New(machine.I2C0)
+	//default settings
+	err := sensor.Configure(lsm303dlhc.Configuration{
+		AccelPowerMode: lsm303dlhc.ACCEL_POWER_NORMAL,
+		AccelRange:     lsm303dlhc.ACCEL_RANGE_2G,
+		AccelDataRate:  lsm303dlhc.ACCEL_DATARATE_100HZ,
+		MagPowerMode:   lsm303dlhc.MAG_POWER_NORMAL,
+		MagSystemMode:  lsm303dlhc.MAG_SYSTEM_CONTINUOUS,
+		MagDataRate:    lsm303dlhc.MAG_DATARATE_10HZ,
+	})
+	if err != nil {
+		for {
+			println("Failed to configure", err.Error())
+			time.Sleep(time.Second)
+		}
+	}
+
+	for {
+		accel_x, accel_y, accel_z, err := sensor.ReadAcceleration()
+		if err != nil {
+			println("Failed to read accel", err.Error())
+		}
+		println("ACCEL_X:", accel_x, " ACCEL_Y:", accel_y, " ACCEL_Z:", accel_z)
+
+		mag_x, mag_y, mag_z, err := sensor.ReadMagneticField()
+		if err != nil {
+			println("Failed to read mag", err.Error())
+		}
+		println("MAG_X:", mag_x, " MAG_Y:", mag_y, " MAG_Z:", mag_z)
+
+		pitch, roll, _ := sensor.ReadPitchRoll()
+		println("Pitch:", float32(pitch), " Roll:", float32(roll))
+
+		heading, _ := sensor.ReadCompass()
+		println("Heading:", float32(heading), "degrees")
+
+		temp, _ := sensor.ReadTemperature()
+		println("Temperature:", float32(temp)/1000, "*C")
+
+		println("\n")
+		time.Sleep(time.Millisecond * 250)
+	}
+
+}

examples/rpio/main.go

@@ -0,0 +1,68 @@
+package main
+
+// Example program for the ST7735 display (Waveshare 1.44" LCD HAT) using the rpio driver on a Raspberry Pi.
+
+import (
+	"fmt"
+	"image/color"
+	"time"
+
+	go_rpio "github.com/stianeikeland/go-rpio/v4"
+	"tinygo.org/x/drivers/rpio"
+	"tinygo.org/x/drivers/st7735"
+)
+
+var (
+	black  = color.RGBA{0, 0, 0, 255}
+	colors = [...]color.RGBA{
+		{255, 0, 0, 255},   // red
+		{0, 255, 0, 255},   // green
+		{0, 0, 255, 255},   // blue
+		{255, 255, 0, 255}, // yellow
+	}
+)
+
+func main() {
+	if err := go_rpio.Open(); err != nil {
+		fmt.Println("Error opening GPIO:", err)
+		return
+	}
+	defer go_rpio.Close()
+
+	// Initialize SPI and pins
+	spi := rpio.NewSPI()
+	resetPin := rpio.NewPin(27)
+	dcPin := rpio.NewPin(25)
+	csPin := rpio.NewPin(8)
+	blPin := rpio.NewPin(24)
+
+	// Initialize display
+	device := st7735.New(spi, resetPin, dcPin, csPin, blPin)
+	device.Configure(st7735.Config{
+		Width:        128,
+		Height:       128,
+		Model:        st7735.GREENTAB,
+		RowOffset:    3,
+		ColumnOffset: 2,
+	})
+	device.InvertColors(false)
+	device.EnableBacklight(true)
+	device.IsBGR(true) // no effect w/o rotation!
+	device.SetRotation(st7735.NO_ROTATION)
+
+	width, height := device.Size()
+
+	// Clear display
+	device.FillScreen(black)
+
+	// Draw rectangles in a loop, clockwise rotation of colors
+	pos := 0
+	for {
+		device.FillRectangle(0, 0, width/2, height/2, colors[(pos+0)%len(colors)])              // top left
+		device.FillRectangle(0, height/2, width/2, height/2, colors[(pos+1)%len(colors)])       // bottom left
+		device.FillRectangle(width/2, height/2, width/2, height/2, colors[(pos+2)%len(colors)]) // bottom right
+		device.FillRectangle(width/2, 0, width/2, height/2, colors[(pos+3)%len(colors)])        // top right
+		pos++
+		time.Sleep(1 * time.Second)
+	}
+}

examples/seesaw/rotary-encoder/main.go

@@ -0,0 +1,35 @@
+package main
+
+import (
+	"machine"
+	"time"
+
+	"tinygo.org/x/drivers/seesaw"
+)
+
+// example reading the position of a rotary encoder (4991) powered by a seesaw
+// https://learn.adafruit.com/adafruit-i2c-qt-rotary-encoder/arduino
+func main() {
+	// This assumes you are using an Adafruit QT Py RP2040 for its Stemma QT connector
+	// https://www.adafruit.com/product/4900
+	i2c := machine.I2C1
+	i2c.Configure(machine.I2CConfig{
+		SCL: machine.I2C1_QT_SCL_PIN,
+		SDA: machine.I2C1_QT_SDA_PIN,
+	})
+
+	dev := seesaw.New(i2c)
+	dev.Address = 0x36
+
+	for {
+		time.Sleep(time.Second)
+
+		pos, err := dev.GetEncoderPosition(0, false)
+		if err != nil {
+			println(err)
+			continue
+		}
+
+		println(pos)
+	}
+}

examples/ssd1306/i2c_128x32/main.go

@@ -1,51 +0,0 @@
-package main
-
-import (
-	"machine"
-
-	"image/color"
-	"time"
-
-	"tinygo.org/x/drivers/ssd1306"
-)
-
-func main() {
-	machine.I2C0.Configure(machine.I2CConfig{
-		Frequency: machine.TWI_FREQ_400KHZ,
-	})
-
-	display := ssd1306.NewI2C(machine.I2C0)
-	display.Configure(ssd1306.Config{
-		Address: ssd1306.Address_128_32,
-		Width:   128,
-		Height:  32,
-	})
-
-	display.ClearDisplay()
-
-	x := int16(0)
-	y := int16(0)
-	deltaX := int16(1)
-	deltaY := int16(1)
-	for {
-		pixel := display.GetPixel(x, y)
-		c := color.RGBA{255, 255, 255, 255}
-		if pixel {
-			c = color.RGBA{0, 0, 0, 255}
-		}
-		display.SetPixel(x, y, c)
-		display.Display()
-
-		x += deltaX
-		y += deltaY
-
-		if x == 0 || x == 127 {
-			deltaX = -deltaX
-		}
-
-		if y == 0 || y == 31 {
-			deltaY = -deltaY
-		}
-		time.Sleep(1 * time.Millisecond)
-	}
-}

examples/ssd1306/i2c_128x64/main.go

@@ -1,60 +0,0 @@
-// This example shows how to use 128x64 display over I2C
-// Tested on Seeeduino XIAO Expansion Board https://wiki.seeedstudio.com/Seeeduino-XIAO-Expansion-Board/
-//
-// According to manual, I2C address of the display is 0x78, but that's 8-bit address.
-// TinyGo operates on 7-bit addresses and respective 7-bit address would be 0x3C, which we use below.
-//
-// To learn more about different types of I2C addresses, please see following page
-// https://www.totalphase.com/support/articles/200349176-7-bit-8-bit-and-10-bit-I2C-Slave-Addressing
-
-package main
-
-import (
-	"machine"
-
-	"image/color"
-	"time"
-
-	"tinygo.org/x/drivers/ssd1306"
-)
-
-func main() {
-	machine.I2C0.Configure(machine.I2CConfig{
-		Frequency: machine.TWI_FREQ_400KHZ,
-	})
-
-	display := ssd1306.NewI2C(machine.I2C0)
-	display.Configure(ssd1306.Config{
-		Address: 0x3C,
-		Width:   128,
-		Height:  64,
-	})
-
-	display.ClearDisplay()
-
-	x := int16(0)
-	y := int16(0)
-	deltaX := int16(1)
-	deltaY := int16(1)
-	for {
-		pixel := display.GetPixel(x, y)
-		c := color.RGBA{255, 255, 255, 255}
-		if pixel {
-			c = color.RGBA{0, 0, 0, 255}
-		}
-		display.SetPixel(x, y, c)
-		display.Display()
-
-		x += deltaX
-		y += deltaY
-
-		if x == 0 || x == 127 {
-			deltaX = -deltaX
-		}
-
-		if y == 0 || y == 63 {
-			deltaY = -deltaY
-		}
-		time.Sleep(1 * time.Millisecond)
-	}
-}

examples/ssd1306/main.go

@@ -0,0 +1,59 @@
+package main
+
+// This example shows how to use SSD1306 OLED display driver over I2C and SPI.
+//
+// Check the `newSSD1306Display()` functions for I2C and SPI initializations.
+
+import (
+	"runtime"
+
+	"image/color"
+	"time"
+)
+
+func main() {
+
+	display := newSSD1306Display()
+	display.ClearDisplay()
+
+	w, h := display.Size()
+	x := int16(0)
+	y := int16(0)
+	deltaX := int16(1)
+	deltaY := int16(1)
+
+	traceTime := time.Now().UnixMilli() + 1000
+	frames := 0
+	ms := runtime.MemStats{}
+
+	for {
+		pixel := display.GetPixel(x, y)
+		c := color.RGBA{255, 255, 255, 255}
+		if pixel {
+			c = color.RGBA{0, 0, 0, 255}
+		}
+		display.SetPixel(x, y, c)
+		display.Display()
+
+		x += deltaX
+		y += deltaY
+
+		if x == 0 || x == w-1 {
+			deltaX = -deltaX
+		}
+
+		if y == 0 || y == h-1 {
+			deltaY = -deltaY
+		}
+
+		frames++
+		now := time.Now().UnixMilli()
+		if now >= traceTime {
+			runtime.ReadMemStats(&ms)
+			println("TS", now, "| FPS", frames, "| HeapInuse", ms.HeapInuse)
+			traceTime = now + 1000
+			frames = 0
+		}
+	}
+
+}

examples/ssd1306/main_i2c_xiao-ble.go

@@ -0,0 +1,38 @@
+//go:build xiao_ble
+
+// This initializes SSD1306 OLED display driver over I2C.
+//
+// Seeed XIAO BLE board + SSD1306 128x32 I2C OLED display.
+//
+// Wiring:
+// - XIAO GND      -> OLED GND
+// - XIAO 3v3      -> OLED VCC
+// - XIAO D4 (SDA) -> OLED SDA
+// - XIAO D5 (SCL) -> OLED SCK
+//
+// For your case:
+// - Connect the display to I2C pins on your board.
+// - Adjust I2C address and display size as needed.
+
+package main
+
+import (
+	"machine"
+
+	"tinygo.org/x/drivers/ssd1306"
+)
+
+func newSSD1306Display() *ssd1306.Device {
+	machine.I2C0.Configure(machine.I2CConfig{
+		Frequency: 400 * machine.KHz,
+		SDA:       machine.SDA0_PIN,
+		SCL:       machine.SCL0_PIN,
+	})
+	display := ssd1306.NewI2C(machine.I2C0)
+	display.Configure(ssd1306.Config{
+		Address: ssd1306.Address_128_32, // or ssd1306.Address
+		Width:   128,
+		Height:  32, // or 64
+	})
+	return display
+}

examples/ssd1306/main_spi_thumby.go

@@ -0,0 +1,27 @@
+//go:build thumby
+
+// This initializes SSD1306 OLED display driver over SPI.
+//
+// Thumby board has a tiny built-in 72x40 display.
+//
+// As the display is built-in, no wiring is needed.
+
+package main
+
+import (
+	"machine"
+
+	"tinygo.org/x/drivers/ssd1306"
+)
+
+func newSSD1306Display() *ssd1306.Device {
+	machine.SPI0.Configure(machine.SPIConfig{})
+	display := ssd1306.NewSPI(machine.SPI0, machine.THUMBY_DC_PIN, machine.THUMBY_RESET_PIN, machine.THUMBY_CS_PIN)
+	display.Configure(ssd1306.Config{
+		Width:     72,
+		Height:    40,
+		ResetCol:  ssd1306.ResetValue{28, 99},
+		ResetPage: ssd1306.ResetValue{0, 5},
+	})
+	return display
+}

examples/ssd1306/main_spi_xiao-rp2040.go

@@ -0,0 +1,40 @@
+//go:build xiao_rp2040
+
+// This initializes SSD1306 OLED display driver over SPI.
+//
+// Seeed XIAO RP2040 board + SSD1306 128x64 SPI OLED display.
+//
+// Wiring:
+// - XIAO GND       -> OLED GND
+// - XIAO 3v3       -> OLED VCC
+// - XIAO D8 (SCK)  -> OLED D0
+// - XIAO D10 (SDO) -> OLED D1
+// - XIAO D4        -> OLED RES
+// - XIAO D5        -> OLED DC
+// - XIAO D6        -> OLED CS
+//
+// For your case:
+// - Connect the display to SPI pins on your board.
+// - Adjust RES, DC and CS pins as needed.
+// - Adjust SPI frequency as needed.
+// - Adjust display size as needed.
+
+package main
+
+import (
+	"machine"
+
+	"tinygo.org/x/drivers/ssd1306"
+)
+
+func newSSD1306Display() *ssd1306.Device {
+	machine.SPI0.Configure(machine.SPIConfig{
+		Frequency: 50 * machine.MHz,
+	})
+	display := ssd1306.NewSPI(machine.SPI0, machine.D5, machine.D4, machine.D6)
+	display.Configure(ssd1306.Config{
+		Width:  128,
+		Height: 64,
+	})
+	return display
+}

examples/ssd1306/spi_128x64/main.go

@@ -1,48 +0,0 @@
-package main
-
-import (
-	"image/color"
-	"machine"
-	"time"
-
-	"tinygo.org/x/drivers/ssd1306"
-)
-
-func main() {
-	machine.SPI0.Configure(machine.SPIConfig{
-		Frequency: 8000000,
-	})
-	display := ssd1306.NewSPI(machine.SPI0, machine.P8, machine.P7, machine.P9)
-	display.Configure(ssd1306.Config{
-		Width:  128,
-		Height: 64,
-	})
-
-	display.ClearDisplay()
-
-	x := int16(64)
-	y := int16(32)
-	deltaX := int16(1)
-	deltaY := int16(1)
-	for {
-		pixel := display.GetPixel(x, y)
-		c := color.RGBA{255, 255, 255, 255}
-		if pixel {
-			c = color.RGBA{0, 0, 0, 255}
-		}
-		display.SetPixel(x, y, c)
-		display.Display()
-
-		x += deltaX
-		y += deltaY
-
-		if x == 0 || x == 127 {
-			deltaX = -deltaX
-		}
-
-		if y == 0 || y == 63 {
-			deltaY = -deltaY
-		}
-		time.Sleep(1 * time.Millisecond)
-	}
-}

examples/ssd1306/spi_thumby/main.go

@@ -1,50 +0,0 @@
-// This example using the SSD1306 OLED display over SPI on the Thumby board
-// A very tiny 72x40 display.
-package main
-
-import (
-	"image/color"
-	"machine"
-	"time"
-
-	"tinygo.org/x/drivers/ssd1306"
-)
-
-func main() {
-	machine.SPI0.Configure(machine.SPIConfig{})
-	display := ssd1306.NewSPI(machine.SPI0, machine.THUMBY_DC_PIN, machine.THUMBY_RESET_PIN, machine.THUMBY_CS_PIN)
-	display.Configure(ssd1306.Config{
-		Width:     72,
-		Height:    40,
-		ResetCol:  ssd1306.ResetValue{28, 99},
-		ResetPage: ssd1306.ResetValue{0, 5},
-	})
-
-	display.ClearDisplay()
-
-	x := int16(36)
-	y := int16(20)
-	deltaX := int16(1)
-	deltaY := int16(1)
-	for {
-		pixel := display.GetPixel(x, y)
-		c := color.RGBA{255, 255, 255, 255}
-		if pixel {
-			c = color.RGBA{0, 0, 0, 255}
-		}
-		display.SetPixel(x, y, c)
-		display.Display()
-
-		x += deltaX
-		y += deltaY
-
-		if x == 0 || x == 71 {
-			deltaX = -deltaX
-		}
-
-		if y == 0 || y == 39 {
-			deltaY = -deltaY
-		}
-		time.Sleep(1 * time.Millisecond)
-	}
-}

flash/devices.go

@@ -46,6 +46,10 @@ var DefaultDeviceIdentifier = DeviceIdentifierFunc(func(id JedecID) Attrs {
 		return GD25Q16C()
 	case 0xC84017:
 		return GD25Q64C()
+	case 0x856015:
+		return P25Q16H()
+	case 0xEF4014:
+		return W25Q80DV()
 	case 0xEF4015:
 		return W25Q16JVIQ()
 	case 0xEF4016:
@@ -239,6 +243,24 @@ func GD25Q64C() Attrs {
 	}
 }
 
+// Settings for the Puya P25Q16H 2MiB SPI flash.
+// Datasheet: https://files.seeedstudio.com/wiki/github_weiruanexample/Flash_P25Q16H-UXH-IR_Datasheet.pdf
+func P25Q16H() Attrs {
+	return Attrs{
+		TotalSize:           1 << 21, // 2 MiB
+		StartUp:             5000 * time.Microsecond,
+		JedecID:             JedecID{0x85, 0x60, 0x15},
+		MaxClockSpeedMHz:    55,
+		QuadEnableBitMask:   0x02,
+		HasSectorProtection: true,
+		SupportsFastRead:    true,
+		SupportsQSPI:        true,
+		SupportsQSPIWrites:  true,
+		WriteStatusSplit:    true,
+		SingleStatusByte:    false,
+	}
+}
+
 // Settings for the Winbond W25Q16JV-IQ 2MiB SPI flash. Note that JV-IM has a
 // different .memory_type (0x70) Datasheet:
 // https://www.winbond.com/resource-files/w25q16jv%20spi%20revf%2005092017.pdf
@@ -380,6 +402,25 @@ func W25Q80DL() Attrs {
 		TotalSize:           1 << 20, // 1 MiB
 		StartUp:             5000 * time.Microsecond,
 		JedecID:             JedecID{0xEF, 0x60, 0x14},
+		MaxClockSpeedMHz:    80,
+		QuadEnableBitMask:   0x02,
+		HasSectorProtection: false,
+		SupportsFastRead:    true,
+		SupportsQSPI:        true,
+		SupportsQSPIWrites:  false,
+		WriteStatusSplit:    false,
+		SingleStatusByte:    false,
+	}
+}
+
+// Settings for the Winbond W25Q80DV 2MiB SPI flash.
+// Datasheet:
+// https://www.winbond.com/resource-files/w25q80dv%20dl_revh_10022015.pdf
+func W25Q80DV() Attrs {
+	return Attrs{
+		TotalSize:           1 << 21, // 2 MiB
+		StartUp:             5000 * time.Microsecond,
+		JedecID:             JedecID{0xEF, 0x40, 0x14},
 		MaxClockSpeedMHz:    104,
 		QuadEnableBitMask:   0x02,
 		HasSectorProtection: false,

go.mod

@@ -12,6 +12,7 @@ require (
 	github.com/google/shlex v0.0.0-20191202100458-e7afc7fbc510
 	github.com/orsinium-labs/tinymath v1.1.0
 	github.com/soypat/natiu-mqtt v0.5.1
+	github.com/stianeikeland/go-rpio/v4 v4.6.0
 	golang.org/x/exp v0.0.0-20241204233417-43b7b7cde48d
 	golang.org/x/net v0.33.0
 	tinygo.org/x/tinyfont v0.3.0

go.sum

@@ -17,6 +17,8 @@ github.com/orsinium-labs/tinymath v1.1.0 h1:KomdsyLHB7vE3f1nRAJF2dyf1m/gnM2HxfTe
 github.com/orsinium-labs/tinymath v1.1.0/go.mod h1:WPXX6ei3KSXG7JfA03a+ekCYaY9SWN4I+JRl2p6ck+A=
 github.com/soypat/natiu-mqtt v0.5.1 h1:rwaDmlvjzD2+3MCOjMZc4QEkDkNwDzbct2TJbpz+TPc=
 github.com/soypat/natiu-mqtt v0.5.1/go.mod h1:xEta+cwop9izVCW7xOx2W+ct9PRMqr0gNVkvBPnQTc4=
+github.com/stianeikeland/go-rpio/v4 v4.6.0 h1:eAJgtw3jTtvn/CqwbC82ntcS+dtzUTgo5qlZKe677EY=
+github.com/stianeikeland/go-rpio/v4 v4.6.0/go.mod h1:A3GvHxC1Om5zaId+HqB3HKqx4K/AqeckxB7qRjxMK7o=
 github.com/valyala/fastjson v1.6.3/go.mod h1:CLCAqky6SMuOcxStkYQvblddUtoRxhYMGLrsQns1aXY=
 golang.org/x/exp v0.0.0-20241204233417-43b7b7cde48d h1:0olWaB5pg3+oychR51GUVCEsGkeCU/2JxjBgIo4f3M0=
 golang.org/x/exp v0.0.0-20241204233417-43b7b7cde48d/go.mod h1:qj5a5QZpwLU2NLQudwIN5koi3beDhSAlJwa67PuM98c=

gps/gps.go

@@ -69,10 +69,16 @@ func NewUART(uart drivers.UART) Device {
 }
 
 // NewI2C creates a new I2C GPS connection.
+// Uses the default i2c address (0x42) for backward compatibility reasons.
 func NewI2C(bus drivers.I2C) Device {
+	return NewI2CWithAddress(bus, I2C_ADDRESS)
+}
+
+// NewI2CWithAddress creates a new I2C GPS connection on the provided address
+func NewI2CWithAddress(bus drivers.I2C, i2cAddress uint16) Device {
 	return Device{
 		bus:      bus,
-		address:  I2C_ADDRESS,
+		address:  i2cAddress,
 		buffer:   make([]byte, bufferSize),
 		bufIdx:   bufferSize,
 		sentence: strings.Builder{},

gps/gpsparser.go

@@ -96,7 +96,10 @@ func (parser *Parser) Parse(sentence string) (Fix, error) {
 		fix.Speed = findSpeed(fields[7])
 		fix.Heading = findHeading(fields[8])
 		date := findDate(fields[9])
-		fix.Time = fix.Time.AddDate(date.Year(), int(date.Month()), date.Day())
+		fix.Time = date.Add(time.Duration(fix.Time.Hour())*time.Hour +
+			time.Duration(fix.Time.Minute())*time.Minute +
+			time.Duration(fix.Time.Second())*time.Second +
+			time.Duration(fix.Time.Nanosecond())*time.Nanosecond)
 
 		return fix, nil
 	}

gps/gpsparser_test.go

@@ -70,15 +70,15 @@ func TestParseRMC(t *testing.T) {
 		t.Error("should have errInvalidRMCSentence error")
 	}
 
-	val = "$GPRMC,203522.00,A,5109.0262308,N,11401.8407342,W,0.004,133.4,130522,0.0,E,D*2B"
+	val = "$GPRMC,203522.00,A,5109.0262308,N,11401.8407342,W,0.004,133.4,010622,0.0,E,D*2B"
 	fix, err := p.Parse(val)
 	if err != nil {
 		t.Error("should have parsed")
 	}
 
 	c.Assert(fix.Time.Year(), qt.Equals, 2022)
-	c.Assert(fix.Time.Month(), qt.Equals, time.May)
-	c.Assert(fix.Time.Day(), qt.Equals, 13)
+	c.Assert(fix.Time.Month(), qt.Equals, time.June)
+	c.Assert(fix.Time.Day(), qt.Equals, 1)
 	c.Assert(fix.Time.Hour(), qt.Equals, 20)
 	c.Assert(fix.Time.Minute(), qt.Equals, 35)
 	c.Assert(fix.Time.Second(), qt.Equals, 22)

gps/registers.go

@@ -4,7 +4,11 @@ package gps
 
 // The I2C address which this device listens to.
 const (
-	I2C_ADDRESS = 0x42
+	// To ensure backward compatibility
+	I2C_ADDRESS = UBLOX_I2C_ADDRESS
+
+	UBLOX_I2C_ADDRESS   = 0x42
+	PA1010D_I2C_ADDRESS = 0x10
 )
 
 const (

hcsr04/hcsr04.go

@@ -5,20 +5,22 @@
 package hcsr04
 
 import (
-	"machine"
 	"time"
+
+	"tinygo.org/x/drivers"
 )
 
 const TIMEOUT = 23324 // max sensing distance (4m)
 
 // Device holds the pins
 type Device struct {
-	trigger machine.Pin
-	echo    machine.Pin
+	trigger drivers.PinOutput
+	echo    drivers.PinInput
 }
 
-// New returns a new ultrasonic driver given 2 pins
-func New(trigger, echo machine.Pin) Device {
+// New returns a new ultrasonic driver given 2 pins.
+// Pins must be configured as output (trigger) and input (echo).
+func New(trigger drivers.PinOutput, echo drivers.PinInput) Device {
 	return Device{
 		trigger: trigger,
 		echo:    echo,
@@ -27,8 +29,7 @@ func New(trigger, echo machine.Pin) Device {
 
 // Configure configures the pins of the Device
 func (d *Device) Configure() {
-	d.trigger.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	d.echo.Configure(machine.PinConfig{Mode: machine.PinInput})
+	// no-op, left for API compatibility
 }
 
 // ReadDistance returns the distance of the object in mm
@@ -45,11 +46,11 @@ func (d *Device) ReadDistance() int32 {
 // ReadPulse returns the time of the pulse (roundtrip) in microseconds
 func (d *Device) ReadPulse() int32 {
 	t := time.Now()
-	d.trigger.Low()
+	d.trigger.Set(false)
 	time.Sleep(2 * time.Microsecond)
-	d.trigger.High()
+	d.trigger.Set(true)
 	time.Sleep(10 * time.Microsecond)
-	d.trigger.Low()
+	d.trigger.Set(false)
 	i := uint8(0)
 	for {
 		if d.echo.Get() {

internal/legacy/pinlegacy_generic.go

@@ -0,0 +1,9 @@
+//go:build !(baremetal && tinygo)
+
+package legacy
+
+import "tinygo.org/x/drivers"
+
+func PinOutput(pin drivers.PinOutput) drivers.PinOutput {
+	return pin
+}

internal/legacy/pinlegacy_tinygo.go

@@ -0,0 +1,16 @@
+//go:build baremetal && tinygo
+
+package legacy
+
+import (
+	"machine"
+
+	"tinygo.org/x/drivers"
+)
+
+func PinOutput(pin drivers.PinOutput) drivers.PinOutput {
+	if p, ok := pin.(machine.Pin); ok {
+		p.Configure(machine.PinConfig{Mode: machine.PinOutput})
+	}
+	return pin
+}

internal/regmap/devices.go

@@ -0,0 +1,121 @@
+package regmap
+
+import (
+	"encoding/binary"
+	"io"
+
+	"tinygo.org/x/drivers"
+)
+
+// Device8 implements common logic to most 8-bit peripherals with an I2C or SPI bus.
+type Device8 struct {
+	buf [10]byte
+}
+
+// clear zeroes Device8's buffers.
+func (d *Device8) clear() {
+	d.buf = [10]byte{}
+}
+
+// I2C methods.
+
+func (d *Device8) Read8I2C(bus drivers.I2C, i2cAddr uint16, addr uint8) (byte, error) {
+	d.buf[0] = addr
+	err := bus.Tx(i2cAddr, d.buf[0:1], d.buf[1:2])
+	return d.buf[1], err
+}
+
+func (d *Device8) Read16I2C(bus drivers.I2C, i2cAddr uint16, addr uint8, order binary.ByteOrder) (uint16, error) {
+	d.buf[0] = addr
+	err := bus.Tx(i2cAddr, d.buf[0:1], d.buf[1:3])
+	return order.Uint16(d.buf[1:3]), err
+}
+
+func (d *Device8) Read32I2C(bus drivers.I2C, i2cAddr uint16, addr uint8, order binary.ByteOrder) (uint32, error) {
+	d.buf[0] = addr
+	err := bus.Tx(i2cAddr, d.buf[0:1], d.buf[1:5])
+	return order.Uint32(d.buf[1:5]), err
+}
+
+func (d *Device8) ReadDataI2C(bus drivers.I2C, i2cAddr uint16, addr uint8, dataDestination []byte) error {
+	d.buf[0] = addr
+	return bus.Tx(i2cAddr, d.buf[:1], dataDestination)
+}
+
+func (d *Device8) Write8I2C(bus drivers.I2C, i2cAddr uint16, addr, value uint8) error {
+	d.buf[0] = addr
+	d.buf[1] = value
+	return bus.Tx(i2cAddr, d.buf[:2], nil)
+}
+
+func (d *Device8) Write16I2C(bus drivers.I2C, i2cAddr uint16, addr uint8, value uint16, order binary.ByteOrder) error {
+	d.buf[0] = addr
+	order.PutUint16(d.buf[1:3], value)
+	return bus.Tx(i2cAddr, d.buf[0:3], nil)
+}
+
+func (d *Device8) Write32I2C(bus drivers.I2C, i2cAddr uint16, addr uint8, value uint32, order binary.ByteOrder) error {
+	d.buf[0] = addr
+	order.PutUint32(d.buf[1:5], value)
+	return bus.Tx(i2cAddr, d.buf[0:5], nil)
+}
+
+// SPI methods.
+
+func (d *Device8) Read8SPI(bus drivers.SPI, addr uint8) (byte, error) {
+	d.clear()
+	d.buf[0] = addr
+	err := bus.Tx(d.buf[0:1], d.buf[1:2]) // We suppose data is returned after first byte in SPI.
+	return d.buf[1], err
+}
+
+func (d *Device8) Read16SPI(bus drivers.SPI, addr uint8, order binary.ByteOrder) (uint16, error) {
+	d.clear()
+	d.buf[0] = addr
+	err := bus.Tx(d.buf[0:3], d.buf[3:6]) // We suppose data is returned after first byte in SPI.
+	return order.Uint16(d.buf[4:6]), err
+}
+
+func (d *Device8) Read32SPI(bus drivers.SPI, addr uint8, order binary.ByteOrder) (uint32, error) {
+	d.clear()
+	d.buf[0] = addr
+	err := bus.Tx(d.buf[0:5], d.buf[5:10]) // We suppose data is returned after first byte in SPI.
+	return order.Uint32(d.buf[6:10]), err
+}
+
+// ReadDataSPI reads data from a 8bit device address. It assumes data at register address is sent back
+// from device after first byte is written as address.
+// It needs the auxiliary buffer length to be large enough to contain both the write and read portions of buffer,
+// so 2*(dataLength+1) < len(auxiliaryBuf) must hold.
+func (d *Device8) ReadDataSPI(bus drivers.SPI, addr uint8, dataLength int, auxiliaryBuf []byte) ([]byte, error) {
+	split := len(auxiliaryBuf) / 2
+	if split < dataLength+1 {
+		return nil, io.ErrShortBuffer
+	}
+
+	wbuf, rbuf := auxiliaryBuf[:split], auxiliaryBuf[split:]
+	wbuf[0] = addr
+	err := bus.Tx(wbuf, rbuf)
+	return rbuf[1:], err
+}
+
+func (d *Device8) Write8SPI(bus drivers.SPI, addr, value uint8) error {
+	d.clear()
+	d.buf[0] = addr
+	d.buf[1] = value
+	return bus.Tx(d.buf[:2], nil)
+}
+
+func (d *Device8) Write16SPI(bus drivers.SPI, addr uint8, value uint16, order binary.ByteOrder) error {
+	d.clear()
+	d.buf[0] = addr
+	order.PutUint16(d.buf[1:3], value)
+	return bus.Tx(d.buf[:3], nil)
+}
+
+func (d *Device8) Write32SPI(bus drivers.SPI, addr uint8, value uint32, order binary.ByteOrder) error {
+	d.clear()
+	d.buf[0] = addr
+	order.PutUint32(d.buf[1:5], value)
+	return bus.Tx(d.buf[:5], nil)
+}

lsm303agr/lsm303agr.go

@@ -36,7 +36,7 @@ type Configuration struct {
 	MagDataRate    uint8
 }
 
-var errNotConnected = errors.New("lsm303agr: failed to communicate with either acel or magnet sensor")
+var errNotConnected = errors.New("lsm303agr: failed to communicate with either accel or magnet sensor")
 
 // New creates a new LSM303AGR connection. The I2C bus must already be configured.
 //

lsm303dlhc/lsm303dlhc.go

@@ -0,0 +1,214 @@
+// Package lsm303dlhc implements a driver for the LSM303dlhc,
+// a 3 axis accelerometer/magnetic sensor typically available on breakout boards.
+//
+// Datasheet: https://www.st.com/resource/en/datasheet/lsm303dlhc.pdf
+
+package lsm303dlhc // import "tinygo.org/x/drivers/lsm303dlhc"
+
+import (
+	"math"
+
+	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+)
+
+// Device wraps an I2C connection to a LSM303dlhc device.
+type Device struct {
+	bus            drivers.I2C
+	AccelAddress   uint8
+	MagAddress     uint8
+	AccelPowerMode uint8
+	AccelRange     uint8
+	AccelDataRate  uint8
+	MagPowerMode   uint8
+	MagSystemMode  uint8
+	MagDataRate    uint8
+	buf            [6]uint8
+}
+
+// Configuration for LSM303dlhc device.
+type Configuration struct {
+	AccelPowerMode uint8
+	AccelRange     uint8
+	AccelDataRate  uint8
+	MagPowerMode   uint8
+	MagSystemMode  uint8
+	MagDataRate    uint8
+}
+
+// New creates a new LSM303DLHC connection. The I2C bus must already be configured.
+// This function only creates the Device object, it does not touch the device.
+func New(bus drivers.I2C) *Device {
+	return &Device{
+		bus:          bus,
+		AccelAddress: ACCEL_ADDRESS,
+		MagAddress:   MAG_ADDRESS,
+	}
+}
+
+// Configure sets up the LSM303dlhc device for communication.
+func (d *Device) Configure(cfg Configuration) (err error) {
+
+	if cfg.AccelDataRate != 0 {
+		d.AccelDataRate = cfg.AccelDataRate
+	} else {
+		d.AccelDataRate = ACCEL_DATARATE_100HZ
+	}
+
+	if cfg.AccelPowerMode != 0 {
+		d.AccelPowerMode = cfg.AccelPowerMode
+	} else {
+		d.AccelPowerMode = ACCEL_POWER_NORMAL
+	}
+
+	if cfg.AccelRange != 0 {
+		d.AccelRange = cfg.AccelRange
+	} else {
+		d.AccelRange = ACCEL_RANGE_2G
+	}
+
+	if cfg.MagPowerMode != 0 {
+		d.MagPowerMode = cfg.MagPowerMode
+	} else {
+		d.MagPowerMode = MAG_POWER_NORMAL
+	}
+
+	if cfg.MagDataRate != 0 {
+		d.MagDataRate = cfg.MagDataRate
+	} else {
+		d.MagDataRate = MAG_DATARATE_10HZ
+	}
+
+	if cfg.MagSystemMode != 0 {
+		d.MagSystemMode = cfg.MagSystemMode
+	} else {
+		d.MagSystemMode = MAG_SYSTEM_CONTINUOUS
+	}
+
+	data := d.buf[:1]
+
+	data[0] = byte(d.AccelDataRate<<4 | d.AccelPowerMode | 0x07)
+	err = legacy.WriteRegister(d.bus, uint8(d.AccelAddress), ACCEL_CTRL_REG1_A, data)
+	if err != nil {
+		return
+	}
+
+	data[0] = byte(0x80 | d.AccelRange<<4)
+	err = legacy.WriteRegister(d.bus, uint8(d.AccelAddress), ACCEL_CTRL_REG4_A, data)
+	if err != nil {
+		return
+	}
+
+	data[0] = byte(0xC0)
+	err = legacy.WriteRegister(d.bus, uint8(d.AccelAddress), CRA_REG_M, data)
+	if err != nil {
+		return
+	}
+
+	// Temperature compensation is on for magnetic sensor
+	data[0] = byte(0x80 | d.MagPowerMode<<4 | d.MagDataRate<<2 | d.MagSystemMode)
+	err = legacy.WriteRegister(d.bus, uint8(d.MagAddress), MAG_MR_REG_M, data)
+	if err != nil {
+		return
+	}
+
+	return nil
+}
+
+// ReadAcceleration reads the current acceleration from the device and returns
+// it in µg (micro-gravity). When one of the axes is pointing straight to Earth
+// and the sensor is not moving the returned value will be around 1000000 or
+// -1000000.
+func (d *Device) ReadAcceleration() (x, y, z int32, err error) {
+	data := d.buf[:6]
+	err = legacy.ReadRegister(d.bus, uint8(d.AccelAddress), ACCEL_OUT_AUTO_INC, data)
+	if err != nil {
+		return
+	}
+
+	rangeFactor := int16(0)
+	switch d.AccelRange {
+	case ACCEL_RANGE_2G:
+		rangeFactor = 1
+	case ACCEL_RANGE_4G:
+		rangeFactor = 2
+	case ACCEL_RANGE_8G:
+		rangeFactor = 4
+	case ACCEL_RANGE_16G:
+		rangeFactor = 12 // the readings in 16G are a bit lower
+	}
+
+	x = int32(int32(int16((uint16(data[1])<<8|uint16(data[0])))>>4*rangeFactor) * 1000000 / 1024)
+	y = int32(int32(int16((uint16(data[3])<<8|uint16(data[2])))>>4*rangeFactor) * 1000000 / 1024)
+	z = int32(int32(int16((uint16(data[5])<<8|uint16(data[4])))>>4*rangeFactor) * 1000000 / 1024)
+	return
+}
+
+// ReadPitchRoll reads the current pitch and roll angles from the device and
+// returns it in micro-degrees. When the z axis is pointing straight to Earth
+// the returned values of pitch and roll would be zero.
+func (d *Device) ReadPitchRoll() (pitch, roll int32, err error) {
+
+	x, y, z, err := d.ReadAcceleration()
+	if err != nil {
+		return
+	}
+	xf, yf, zf := float64(x), float64(y), float64(z)
+	pitch = int32((math.Round(math.Atan2(yf, math.Sqrt(math.Pow(xf, 2)+math.Pow(zf, 2)))*(180/math.Pi)*100) / 100) * 1000000)
+	roll = int32((math.Round(math.Atan2(xf, math.Sqrt(math.Pow(yf, 2)+math.Pow(zf, 2)))*(180/math.Pi)*100) / 100) * 1000000)
+	return
+
+}
+
+// ReadMagneticField reads the current magnetic field from the device and returns
+// it in mG (milligauss). 1 mG = 0.1 µT (microtesla).
+func (d *Device) ReadMagneticField() (x, y, z int32, err error) {
+
+	if d.MagSystemMode == MAG_SYSTEM_SINGLE {
+		cmd := d.buf[:1]
+		cmd[0] = byte(0x80 | d.MagPowerMode<<4 | d.MagDataRate<<2 | d.MagSystemMode)
+		err = legacy.WriteRegister(d.bus, uint8(d.MagAddress), MAG_MR_REG_M, cmd)
+		if err != nil {
+			return
+		}
+	}
+
+	data := d.buf[0:6]
+	legacy.ReadRegister(d.bus, uint8(d.MagAddress), MAG_OUT_AUTO_INC, data)
+
+	x = int32(int16((uint16(data[1])<<8 | uint16(data[0]))))
+	y = int32(int16((uint16(data[3])<<8 | uint16(data[2]))))
+	z = int32(int16((uint16(data[5])<<8 | uint16(data[4]))))
+	return
+}
+
+// ReadCompass reads the current compass heading from the device and returns
+// it in micro-degrees. When the z axis is pointing straight to Earth and
+// the y axis is pointing to North, the heading would be zero.
+//
+// However, the heading may be off due to electronic compasses would be effected
+// by strong magnetic fields and require constant calibration.
+func (d *Device) ReadCompass() (h int32, err error) {
+
+	x, y, _, err := d.ReadMagneticField()
+	if err != nil {
+		return
+	}
+	xf, yf := float64(x), float64(y)
+	h = int32(float32((180/math.Pi)*math.Atan2(yf, xf)) * 1000000)
+	return
+}
+
+// ReadTemperature returns the temperature in Celsius milli degrees (°C/1000)
+func (d *Device) ReadTemperature() (t int32, err error) {
+
+	data := d.buf[:2]
+	err = legacy.ReadRegister(d.bus, uint8(d.MagAddress), TEMP_OUT_AUTO_INC, data)
+	if err != nil {
+		return
+	}
+
+	r := int16((uint16(data[1])<<8 | uint16(data[0]))) >> 4 // temperature offset from 25 °C
+	t = 25000 + int32((float32(r)/8)*1000)
+	return
+}

lsm303dlhc/registers.go

@@ -0,0 +1,75 @@
+package lsm303dlhc
+
+const (
+
+	// Constants/addresses used for I2C.
+	ACCEL_ADDRESS = 0x19
+	MAG_ADDRESS   = 0x1E
+
+	// i2C 8-bit subaddress (SUB): the 7 LSb represent the actual register address
+	// while the MSB enables address auto increment.
+	// If the MSb of the SUB field is 1, the SUB (register address) is
+	// automatically increased to allow multiple data read/writes.
+	ADDR_AUTO_INC_MASK = 0x80
+
+	// accelerometer registers.
+	ACCEL_CTRL_REG1_A  = 0x20
+	ACCEL_CTRL_REG4_A  = 0x23
+	ACCEL_OUT_X_L_A    = 0x28
+	ACCEL_OUT_X_H_A    = 0x29
+	ACCEL_OUT_Y_L_A    = 0x2A
+	ACCEL_OUT_Y_H_A    = 0x2B
+	ACCEL_OUT_Z_L_A    = 0x2C
+	ACCEL_OUT_Z_H_A    = 0x2D
+	ACCEL_OUT_AUTO_INC = ACCEL_OUT_X_L_A | ADDR_AUTO_INC_MASK
+
+	// magnetic sensor registers.
+	MAG_MR_REG_M     = 0x02
+	MAG_OUT_X_L_M    = 0x68
+	MAG_OUT_X_H_M    = 0x69
+	MAG_OUT_Y_L_M    = 0x6A
+	MAG_OUT_Y_H_M    = 0x6B
+	MAG_OUT_Z_L_M    = 0x6C
+	MAG_OUT_Z_H_M    = 0x6D
+	MAG_OUT_AUTO_INC = MAG_OUT_X_L_M | ADDR_AUTO_INC_MASK
+
+	// temperature sensor registers.
+	CRA_REG_M         = 0x80
+	TEMP_OUT_L_M      = 0x32
+	TEMP_OUT_H_M      = 0x31
+	TEMP_OUT_AUTO_INC = TEMP_OUT_L_M | ADDR_AUTO_INC_MASK
+
+	// accelerometer power mode.
+	ACCEL_POWER_NORMAL = 0x00 // default
+	ACCEL_POWER_LOW    = 0x08
+
+	// accelerometer range.
+	ACCEL_RANGE_2G  = 0x00 // default
+	ACCEL_RANGE_4G  = 0x01
+	ACCEL_RANGE_8G  = 0x02
+	ACCEL_RANGE_16G = 0x03
+
+	// accelerometer data rate.
+	ACCEL_DATARATE_1HZ    = 0x01
+	ACCEL_DATARATE_10HZ   = 0x02
+	ACCEL_DATARATE_25HZ   = 0x03
+	ACCEL_DATARATE_50HZ   = 0x04
+	ACCEL_DATARATE_100HZ  = 0x05 // default
+	ACCEL_DATARATE_200HZ  = 0x06
+	ACCEL_DATARATE_400HZ  = 0x07
+	ACCEL_DATARATE_1344HZ = 0x09 // 5376Hz in low-power mode
+
+	// magnetic sensor power mode.
+	MAG_POWER_NORMAL = 0x00 // default
+	MAG_POWER_LOW    = 0x01
+
+	// magnetic sensor operate mode.
+	MAG_SYSTEM_CONTINUOUS = 0x00 // default
+	MAG_SYSTEM_SINGLE     = 0x01
+
+	// magnetic sensor data rate
+	MAG_DATARATE_10HZ  = 0x00 // default
+	MAG_DATARATE_20HZ  = 0x01
+	MAG_DATARATE_50HZ  = 0x02
+	MAG_DATARATE_100HZ = 0x03
+)

lsm6ds3tr/lsm6ds3tr.go

@@ -8,7 +8,6 @@ import (
 	"errors"
 
 	"tinygo.org/x/drivers"
-	"tinygo.org/x/drivers/internal/legacy"
 )
 
 type AccelRange uint8
@@ -26,7 +25,7 @@ type Device struct {
 	accelSampleRate AccelSampleRate
 	gyroRange       GyroRange
 	gyroSampleRate  GyroSampleRate
-	buf             [6]uint8
+	buf             [7]uint8 // up to 6 bytes for read + 1 byte for the register address
 }
 
 // Configuration for LSM6DS3TR device.
@@ -84,30 +83,20 @@ func (d *Device) doConfigure(cfg Configuration) (err error) {
 		d.gyroSampleRate = GYRO_SR_104
 	}
 
-	data := d.buf[:1]
-
 	// Configure accelerometer
-	data[0] = uint8(d.accelRange) | uint8(d.accelSampleRate)
-	err = legacy.WriteRegister(d.bus, uint8(d.Address), CTRL1_XL, data)
+	err = d.writeByte(CTRL1_XL, uint8(d.accelRange)|uint8(d.accelSampleRate))
 	if err != nil {
 		return
 	}
 
-	// Set ODR bit
-	err = legacy.ReadRegister(d.bus, uint8(d.Address), CTRL4_C, data)
-	if err != nil {
-		return
-	}
-	data[0] = data[0] &^ BW_SCAL_ODR_ENABLED
-	data[0] |= BW_SCAL_ODR_ENABLED
-	err = legacy.WriteRegister(d.bus, uint8(d.Address), CTRL4_C, data)
+	// Enable ODR scaling
+	err = d.setBits(CTRL4_C, BW_SCAL_ODR_ENABLED)
 	if err != nil {
 		return
 	}
 
 	// Configure gyroscope
-	data[0] = uint8(d.gyroRange) | uint8(d.gyroSampleRate)
-	err = legacy.WriteRegister(d.bus, uint8(d.Address), CTRL2_G, data)
+	err = d.writeByte(CTRL2_G, uint8(d.gyroRange)|uint8(d.gyroSampleRate))
 	if err != nil {
 		return
 	}
@@ -118,8 +107,10 @@ func (d *Device) doConfigure(cfg Configuration) (err error) {
 // Connected returns whether a LSM6DS3TR has been found.
 // It does a "who am I" request and checks the response.
 func (d *Device) Connected() bool {
-	data := d.buf[:1]
-	legacy.ReadRegister(d.bus, uint8(d.Address), WHO_AM_I, data)
+	data, err := d.readBytes(WHO_AM_I, 1)
+	if err != nil {
+		return false
+	}
 	return data[0] == 0x6A
 }
 
@@ -128,8 +119,7 @@ func (d *Device) Connected() bool {
 // and the sensor is not moving the returned value will be around 1000000 or
 // -1000000.
 func (d *Device) ReadAcceleration() (x, y, z int32, err error) {
-	data := d.buf[:6]
-	err = legacy.ReadRegister(d.bus, uint8(d.Address), OUTX_L_XL, data)
+	data, err := d.readBytes(OUTX_L_XL, 6)
 	if err != nil {
 		return
 	}
@@ -153,8 +143,7 @@ func (d *Device) ReadAcceleration() (x, y, z int32, err error) {
 // rotation along one axis and while doing so integrate all values over time,
 // you would get a value close to 360000000.
 func (d *Device) ReadRotation() (x, y, z int32, err error) {
-	data := d.buf[:6]
-	err = legacy.ReadRegister(d.bus, uint8(d.Address), OUTX_L_G, data)
+	data, err := d.readBytes(OUTX_L_G, 6)
 	if err != nil {
 		return
 	}
@@ -177,8 +166,7 @@ func (d *Device) ReadRotation() (x, y, z int32, err error) {
 
 // ReadTemperature returns the temperature in celsius milli degrees (°C/1000)
 func (d *Device) ReadTemperature() (t int32, err error) {
-	data := d.buf[:2]
-	err = legacy.ReadRegister(d.bus, uint8(d.Address), OUT_TEMP_L, data)
+	data, err := d.readBytes(OUT_TEMP_L, 2)
 	if err != nil {
 		return
 	}
@@ -187,3 +175,26 @@ func (d *Device) ReadTemperature() (t int32, err error) {
 	t = 25000 + (int32(int16((int16(data[1])<<8)|int16(data[0])))*125)/32
 	return
 }
+
+func (d *Device) readBytes(reg, size uint8) ([]byte, error) {
+	d.buf[0] = reg
+	err := d.bus.Tx(d.Address, d.buf[0:1], d.buf[1:size+1])
+	if err != nil {
+		return nil, err
+	}
+	return d.buf[1 : size+1], nil
+}
+
+func (d *Device) writeByte(reg, value uint8) error {
+	d.buf[0] = reg
+	d.buf[1] = value
+	return d.bus.Tx(d.Address, d.buf[0:2], nil)
+}
+
+func (d *Device) setBits(reg, bits uint8) error {
+	data, err := d.readBytes(reg, 1)
+	if err != nil {
+		return err
+	}
+	return d.writeByte(reg, (data[0]&^bits)|bits)
+}

pin.go

@@ -0,0 +1,41 @@
+package drivers
+
+// Pin types abstract the underlying implementation of a pin,
+// allowing the use of different hardware or libraries without changing driver code.
+//
+// Note, pin mode functionality is not part of the Pin interface.
+// Client code is responsible for configuring pin modes correctly.
+// This can be done either before passing the pin to a driver constructor
+// or by ensuring correct pin mode is set when Get or Set methods are called.
+// See rpio package for an example of a pin implementation that does this.
+//
+// Drivers that used to configure output pin mode in their constructors can use
+// legacy.PinOutput() wrapper to keep the same behavior for machine.Pin.
+// See internal/legacy/pinlegacy_tinygo.go and internal/legacy/pinlegacy_generic.go for details.
+//
+// All new drivers are encouraged to not configure pin modes in their constructors and
+// do not depend on either machine package or legacy wrappers.
+
+// PinInput is an interface for reading the state of a pin.
+type PinInput interface {
+	Get() bool
+}
+
+// PinOutput is an interface for setting the state of a pin.
+type PinOutput interface {
+	Set(bool)
+}
+
+// Pin is an interface for a pin that can be both input and output.
+type Pin interface {
+	PinInput
+	PinOutput
+}
+
+// PinGet is a function type for getting the state of a pin
+// Shall be used in high-performance drivers to avoid interface call overhead.
+type PinGet func() bool
+
+// PinSet is a function type for setting the state of a pin.
+// Shall be used in high-performance drivers to avoid interface call overhead.
+type PinSet func(bool)

rpio/pin.go

@@ -0,0 +1,37 @@
+// Implementation of the Pin interface for the Raspberry Pi GPIO pins.
+// Depends on the go-rpio library.
+// Configures pin modes automatically when Get or Set methods are called.
+
+package rpio // import "tinygo.org/x/drivers/rpio"
+
+import go_rpio "github.com/stianeikeland/go-rpio/v4"
+
+type Pin struct {
+	modeSet bool
+	Mode    go_rpio.Mode
+	Pin     go_rpio.Pin
+}
+
+func NewPin(pinNumber int) *Pin {
+	return &Pin{Pin: go_rpio.Pin(pinNumber)}
+}
+
+func (p *Pin) Get() bool {
+	if !p.modeSet || p.Mode != go_rpio.Input {
+		p.Pin.Input()
+		p.Mode = go_rpio.Input
+	}
+	return p.Pin.Read() == go_rpio.High
+}
+
+func (p *Pin) Set(high bool) {
+	if !p.modeSet || p.Mode != go_rpio.Output {
+		p.Pin.Output()
+		p.Mode = go_rpio.Output
+	}
+	state := go_rpio.Low
+	if high {
+		state = go_rpio.High
+	}
+	p.Pin.Write(state)
+}

rpio/spi.go

@@ -0,0 +1,30 @@
+package rpio // import "tinygo.org/x/drivers/rpio"
+
+import go_rpio "github.com/stianeikeland/go-rpio/v4"
+
+type SPI struct {
+}
+
+func NewSPI() (s *SPI) {
+	if err := go_rpio.SpiBegin(go_rpio.Spi0); err != nil {
+		panic(err)
+	}
+	go_rpio.SpiSpeed(25_000_000) // 25 MHz
+	go_rpio.SpiChipSelect(0)
+	return &SPI{}
+}
+
+func (s *SPI) Tx(w, r []byte) error {
+	data := make([]byte, len(w))
+	copy(data, w)
+	go_rpio.SpiExchange(data)
+	copy(r, data)
+	return nil
+}
+
+func (s *SPI) Transfer(b byte) (byte, error) {
+	w := []byte{b}
+	r := make([]byte, len(w))
+	err := s.Tx(w, r)
+	return r[0], err
+}

seesaw/encoder.go

@@ -0,0 +1,49 @@
+package seesaw
+
+import (
+	"errors"
+)
+
+var errInvalidEncoderNumber = errors.New("invalid encoder choice, 0-15 are supported")
+
+// GetEncoderPosition returns the absolute position (or delta since the previous call) of the specified rotary encoder.
+func (d *Device) GetEncoderPosition(encoder uint, asDelta bool) (int32, error) {
+	if encoder >= 16 {
+		return 0, errInvalidEncoderNumber
+	}
+
+	// The function address' upper nibble is the function, the lower nibble selects which encoder to communicate with
+	fnAddr := FunctionAddress(encoder)
+	if asDelta {
+		fnAddr |= FunctionEncoderDelta
+	} else {
+		fnAddr |= FunctionEncoderPosition
+	}
+
+	var buf [4]byte
+	err := d.Read(ModuleEncoderBase, fnAddr, buf[:])
+	if err != nil {
+		return 0, err
+	}
+
+	return int32(buf[0])<<24 | int32(buf[1])<<16 | int32(buf[2])<<8 | int32(buf[3]), nil
+}
+
+// SetEncoderPosition calibrate's the encoder's current absolute position to be whatever the provided position is.
+func (d *Device) SetEncoderPosition(encoder uint, position int32) error {
+	if encoder >= 16 {
+		return errInvalidEncoderNumber
+	}
+
+	// The function address' upper nibble is the function, the lower nibble selects which encoder to communicate with
+	fnAddr := FunctionEncoderPosition | FunctionAddress(encoder)
+
+	buf := [4]byte{
+		byte(position >> 24),
+		byte(position >> 16),
+		byte(position >> 8),
+		byte(position),
+	}
+
+	return d.Write(ModuleEncoderBase, fnAddr, buf[:])
+}

seesaw/registers.go

@@ -98,3 +98,13 @@ const (
 	FunctionKeypadCount    FunctionAddress = 0x04
 	FunctionKeypadFifo     FunctionAddress = 0x10
 )
+
+// encoder module function address registers
+// these are the defaults for encoder 0, change the lower nibble to address other encoders
+// see the Device.GetEncoderPosition and SetEncoderPosition methods for examples.
+const (
+	FunctionEncoderIntenset FunctionAddress = 0x10
+	FunctionEncoderIntenclr FunctionAddress = 0x20
+	FunctionEncoderPosition FunctionAddress = 0x30
+	FunctionEncoderDelta    FunctionAddress = 0x40
+)

smoketest.sh

@@ -44,6 +44,7 @@ tinygo build -size short -o ./build/test.hex -target=pyportal ./examples/ili9341
 tinygo build -size short -o ./build/test.hex -target=circuitplay-express ./examples/lis3dh/main.go
 tinygo build -size short -o ./build/test.hex -target=nano-33-ble ./examples/lps22hb/main.go
 tinygo build -size short -o ./build/test.hex -target=microbit ./examples/lsm303agr/main.go
+tinygo build -size short -o ./build/test.hex -target=feather-m4 ./examples/lsm303dlhc/main.go
 tinygo build -size short -o ./build/test.hex -target=arduino-nano33 ./examples/lsm6ds3/main.go
 tinygo build -size short -o ./build/test.hex -target=itsybitsy-m0 ./examples/mag3110/main.go
 tinygo build -size short -o ./build/test.hex -target=itsybitsy-m0 ./examples/mcp23017/main.go
@@ -58,15 +59,17 @@ tinygo build -size short -o ./build/test.hex -target=p1am-100 ./examples/p1am/ma
 tinygo build -size short -o ./build/test.hex -target=pico ./examples/pca9685/main.go
 tinygo build -size short -o ./build/test.hex -target=microbit ./examples/pcd8544/setbuffer/main.go
 tinygo build -size short -o ./build/test.hex -target=microbit ./examples/pcd8544/setpixel/main.go
-tinygo build -size short -o ./build/test.hex -target=feather-rp2040 ./examples/seesaw
+tinygo build -size short -o ./build/test.hex -target=feather-rp2040 ./examples/seesaw/soil-sensor
+tinygo build -size short -o ./build/test.hex -target=qtpy-rp2040 ./examples/seesaw/rotary-encoder
 tinygo build -size short -o ./build/test.hex -target=arduino ./examples/servo
 tinygo build -size short -o ./build/test.hex -target=pico     ./examples/sgp30
 tinygo build -size short -o ./build/test.hex -target=pybadge ./examples/shifter/main.go
 tinygo build -size short -o ./build/test.hex -target=microbit ./examples/sht3x/main.go
 tinygo build -size short -o ./build/test.hex -target=microbit ./examples/sht4x/main.go
 tinygo build -size short -o ./build/test.hex -target=microbit ./examples/shtc3/main.go
-tinygo build -size short -o ./build/test.hex -target=microbit ./examples/ssd1306/i2c_128x32/main.go
-tinygo build -size short -o ./build/test.hex -target=microbit ./examples/ssd1306/spi_128x64/main.go
+tinygo build -size short -o ./build/test.hex -target=xiao-ble ./examples/ssd1306/
+tinygo build -size short -o ./build/test.hex -target=xiao-rp2040 ./examples/ssd1306/
+tinygo build -size short -o ./build/test.hex -target=thumby ./examples/ssd1306/
 tinygo build -size short -o ./build/test.hex -target=microbit ./examples/ssd1331/main.go
 tinygo build -size short -o ./build/test.hex -target=microbit ./examples/st7735/main.go
 tinygo build -size short -o ./build/test.hex -target=microbit ./examples/st7789/main.go
@@ -140,6 +143,7 @@ tinygo build -size short -o ./build/test.uf2 -target=pico ./examples/tmc2209/mai
 tinygo build -size short -o ./build/test.hex -target=pico ./examples/tmc5160/main.go
 tinygo build -size short -o ./build/test.uf2 -target=nicenano ./examples/sharpmem/main.go
 tinygo build -size short -o ./build/test.hex -target=feather-nrf52840 ./examples/max6675/main.go
+tinygo build -size short -o ./build/test.hex -target=pico ./examples/ens160/main.go
 # network examples (espat)
 tinygo build -size short -o ./build/test.hex -target=challenger-rp2040 ./examples/net/ntpclient/
 # network examples (wifinina)

ssd1306/ssd1306.go

@@ -6,11 +6,9 @@ package ssd1306 // import "tinygo.org/x/drivers/ssd1306"
 import (
 	"errors"
 	"image/color"
-	"machine"
 	"time"
 
 	"tinygo.org/x/drivers"
-	"tinygo.org/x/drivers/internal/legacy"
 	"tinygo.org/x/drivers/pixel"
 )
 
@@ -23,16 +21,15 @@ type ResetValue [2]byte
 
 // Device wraps I2C or SPI connection.
 type Device struct {
-	bus        Buser
-	buffer     []byte
-	width      int16
-	height     int16
-	bufferSize int16
-	vccState   VccMode
-	canReset   bool
-	resetCol   ResetValue
-	resetPage  ResetValue
-	rotation   drivers.Rotation
+	bus       Buser
+	buffer    []byte
+	width     int16
+	height    int16
+	vccState  VccMode
+	canReset  bool
+	resetCol  ResetValue
+	resetPage ResetValue
+	rotation  drivers.Rotation
 }
 
 // Config is the configuration for the display
@@ -51,51 +48,15 @@ type Config struct {
 	Rotation  drivers.Rotation
 }
 
-type I2CBus struct {
-	wire    drivers.I2C
-	Address uint16
-}
-
-type SPIBus struct {
-	wire     drivers.SPI
-	dcPin    machine.Pin
-	resetPin machine.Pin
-	csPin    machine.Pin
-}
-
 type Buser interface {
-	configure() error
-	tx(data []byte, isCommand bool) error
-	setAddress(address uint16) error
+	configure(address uint16, size int16) []byte // configure the bus and return the image buffer to use
+	command(cmd uint8) error                     // send a command to the display
+	flush() error                                // send the image to the display, faster than "tx()" in i2c case since avoids slice copy
+	tx(data []byte, isCommand bool) error        // generic transmit function
 }
 
 type VccMode uint8
 
-// NewI2C creates a new SSD1306 connection. The I2C wire must already be configured.
-func NewI2C(bus drivers.I2C) Device {
-	return Device{
-		bus: &I2CBus{
-			wire:    bus,
-			Address: Address,
-		},
-	}
-}
-
-// NewSPI creates a new SSD1306 connection. The SPI wire must already be configured.
-func NewSPI(bus drivers.SPI, dcPin, resetPin, csPin machine.Pin) Device {
-	dcPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	resetPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	csPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	return Device{
-		bus: &SPIBus{
-			wire:     bus,
-			dcPin:    dcPin,
-			resetPin: resetPin,
-			csPin:    csPin,
-		},
-	}
-}
-
 // Configure initializes the display with default configuration
 func (d *Device) Configure(cfg Config) {
 	var zeroReset ResetValue
@@ -109,9 +70,6 @@ func (d *Device) Configure(cfg Config) {
 	} else {
 		d.height = 64
 	}
-	if cfg.Address != 0 {
-		d.bus.setAddress(cfg.Address)
-	}
 	if cfg.VccState != 0 {
 		d.vccState = cfg.VccState
 	} else {
@@ -127,11 +85,9 @@ func (d *Device) Configure(cfg Config) {
 	} else {
 		d.resetPage = ResetValue{0, uint8(d.height/8) - 1}
 	}
-	d.bufferSize = d.width * d.height / 8
-	d.buffer = make([]byte, d.bufferSize)
 	d.canReset = cfg.Address != 0 || d.width != 128 || d.height != 64 // I2C or not 128x64
 
-	d.bus.configure()
+	d.buffer = d.bus.configure(cfg.Address, d.width*d.height/8)
 
 	time.Sleep(100 * time.Nanosecond)
 	d.Command(DISPLAYOFF)
@@ -193,11 +149,22 @@ func (d *Device) Configure(cfg Config) {
 	d.Command(NORMALDISPLAY)
 	d.Command(DEACTIVATE_SCROLL)
 	d.Command(DISPLAYON)
+
+}
+
+// Command sends a command to the display
+func (d *Device) Command(command uint8) {
+	d.bus.command(command)
+}
+
+// Tx sends data to the display; if isCommand is false, this also updates the image buffer.
+func (d *Device) Tx(data []byte, isCommand bool) error {
+	return d.bus.tx(data, isCommand)
 }
 
 // ClearBuffer clears the image buffer
 func (d *Device) ClearBuffer() {
-	for i := int16(0); i < d.bufferSize; i++ {
+	for i := 0; i < len(d.buffer); i++ {
 		d.buffer[i] = 0
 	}
 }
@@ -223,7 +190,7 @@ func (d *Device) Display() error {
 		d.Command(d.resetPage[1])
 	}
 
-	return d.Tx(d.buffer, false)
+	return d.bus.flush()
 }
 
 // SetPixel enables or disables a pixel in the buffer
@@ -252,12 +219,10 @@ func (d *Device) GetPixel(x int16, y int16) bool {
 
 // SetBuffer changes the whole buffer at once
 func (d *Device) SetBuffer(buffer []byte) error {
-	if int16(len(buffer)) != d.bufferSize {
+	if len(buffer) != len(d.buffer) {
 		return errBufferSize
 	}
-	for i := int16(0); i < d.bufferSize; i++ {
-		d.buffer[i] = buffer[i]
-	}
+	copy(d.buffer, buffer)
 	return nil
 }
 
@@ -266,79 +231,6 @@ func (d *Device) GetBuffer() []byte {
 	return d.buffer
 }
 
-// Command sends a command to the display
-func (d *Device) Command(command uint8) {
-	d.bus.tx([]byte{command}, true)
-}
-
-// setAddress sets the address to the I2C bus
-func (b *I2CBus) setAddress(address uint16) error {
-	b.Address = address
-	return nil
-}
-
-// setAddress does nothing, but it's required to avoid reflection
-func (b *SPIBus) setAddress(address uint16) error {
-	// do nothing
-	println("trying to Configure an address on a SPI device")
-	return nil
-}
-
-// configure does nothing, but it's required to avoid reflection
-func (b *I2CBus) configure() error { return nil }
-
-// configure configures some pins with the SPI bus
-func (b *SPIBus) configure() error {
-	b.csPin.Low()
-	b.dcPin.Low()
-	b.resetPin.Low()
-
-	b.resetPin.High()
-	time.Sleep(1 * time.Millisecond)
-	b.resetPin.Low()
-	time.Sleep(10 * time.Millisecond)
-	b.resetPin.High()
-
-	return nil
-}
-
-// Tx sends data to the display
-func (d *Device) Tx(data []byte, isCommand bool) error {
-	return d.bus.tx(data, isCommand)
-}
-
-// tx sends data to the display (I2CBus implementation)
-func (b *I2CBus) tx(data []byte, isCommand bool) error {
-	if isCommand {
-		return legacy.WriteRegister(b.wire, uint8(b.Address), 0x00, data)
-	} else {
-		return legacy.WriteRegister(b.wire, uint8(b.Address), 0x40, data)
-	}
-}
-
-// tx sends data to the display (SPIBus implementation)
-func (b *SPIBus) tx(data []byte, isCommand bool) error {
-	var err error
-
-	if isCommand {
-		b.csPin.High()
-		b.dcPin.Low()
-		b.csPin.Low()
-
-		err = b.wire.Tx(data, nil)
-		b.csPin.High()
-	} else {
-		b.csPin.High()
-		b.dcPin.High()
-		b.csPin.Low()
-
-		err = b.wire.Tx(data, nil)
-		b.csPin.High()
-	}
-
-	return err
-}
-
 // Size returns the current size of the display.
 func (d *Device) Size() (w, h int16) {
 	return d.width, d.height

ssd1306/ssd1306_i2c.go

@@ -0,0 +1,52 @@
+package ssd1306
+
+import (
+	"tinygo.org/x/drivers"
+)
+
+type I2CBus struct {
+	wire    drivers.I2C
+	address uint16
+	buffer  []byte // buffer to avoid heap allocations
+}
+
+// NewI2C creates a new SSD1306 connection. The I2C wire must already be configured.
+func NewI2C(bus drivers.I2C) *Device {
+	return &Device{
+		bus: &I2CBus{
+			wire:    bus,
+			address: Address,
+		},
+	}
+}
+
+// configure address for the I2C bus and allocate the buffer
+func (b *I2CBus) configure(address uint16, size int16) []byte {
+	if address != 0 {
+		b.address = address
+	}
+	b.buffer = make([]byte, size+2) // +1 for the mode and +1 for a command
+	return b.buffer[2:]             // return the image buffer
+}
+
+// command sends a command to the display
+func (b *I2CBus) command(cmd uint8) error {
+	b.buffer[0] = 0x00 // Command mode
+	b.buffer[1] = cmd
+	return b.wire.Tx(b.address, b.buffer[:2], nil)
+}
+
+// flush sends the image to the display
+func (b *I2CBus) flush() error {
+	b.buffer[1] = 0x40 // Data mode
+	return b.wire.Tx(b.address, b.buffer[1:], nil)
+}
+
+// tx sends data to the display
+func (b *I2CBus) tx(data []byte, isCommand bool) error {
+	if isCommand {
+		return b.command(data[0])
+	}
+	copy(b.buffer[2:], data)
+	return b.flush()
+}

ssd1306/ssd1306_spi.go

@@ -0,0 +1,65 @@
+package ssd1306
+
+import (
+	"time"
+
+	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
+)
+
+type SPIBus struct {
+	wire     drivers.SPI
+	dcPin    drivers.PinOutput
+	resetPin drivers.PinOutput
+	csPin    drivers.PinOutput
+	buffer   []byte // buffer to avoid heap allocations
+}
+
+// NewSPI creates a new SSD1306 connection. The SPI wire must already be configured.
+func NewSPI(bus drivers.SPI, dcPin, resetPin, csPin drivers.PinOutput) *Device {
+	return &Device{
+		bus: &SPIBus{
+			wire:     bus,
+			dcPin:    legacy.PinOutput(dcPin),
+			resetPin: legacy.PinOutput(resetPin),
+			csPin:    legacy.PinOutput(csPin),
+		},
+	}
+}
+
+// configure pins with the SPI bus and allocate the buffer
+func (b *SPIBus) configure(address uint16, size int16) []byte {
+	b.csPin.Set(false)
+	b.dcPin.Set(false)
+	b.resetPin.Set(false)
+
+	b.resetPin.Set(true)
+	time.Sleep(1 * time.Millisecond)
+	b.resetPin.Set(false)
+	time.Sleep(10 * time.Millisecond)
+	b.resetPin.Set(true)
+
+	b.buffer = make([]byte, size+1) // +1 for a command
+	return b.buffer[1:]             // return the image buffer
+}
+
+// command sends a command to the display
+func (b *SPIBus) command(cmd uint8) error {
+	b.buffer[0] = cmd
+	return b.tx(b.buffer[:1], true)
+}
+
+// flush sends the image to the display
+func (b *SPIBus) flush() error {
+	return b.tx(b.buffer[1:], false)
+}
+
+// tx sends data to the display
+func (b *SPIBus) tx(data []byte, isCommand bool) error {
+	b.csPin.Set(true)
+	b.dcPin.Set(!isCommand)
+	b.csPin.Set(false)
+	err := b.wire.Tx(data, nil)
+	b.csPin.Set(true)
+	return err
+}

st7735/st7735.go

@@ -5,12 +5,12 @@ package st7735 // import "tinygo.org/x/drivers/st7735"
 
 import (
 	"image/color"
-	"machine"
 	"time"
 
 	"errors"
 
 	"tinygo.org/x/drivers"
+	"tinygo.org/x/drivers/internal/legacy"
 	"tinygo.org/x/drivers/pixel"
 )
 
@@ -39,10 +39,10 @@ type Device = DeviceOf[pixel.RGB565BE]
 // formats.
 type DeviceOf[T Color] struct {
 	bus          drivers.SPI
-	dcPin        machine.Pin
-	resetPin     machine.Pin
-	csPin        machine.Pin
-	blPin        machine.Pin
+	dcPin        drivers.PinOutput
+	resetPin     drivers.PinOutput
+	csPin        drivers.PinOutput
+	blPin        drivers.PinOutput
 	width        int16
 	height       int16
 	columnOffset int16
@@ -65,23 +65,19 @@ type Config struct {
 }
 
 // New creates a new ST7735 connection. The SPI wire must already be configured.
-func New(bus drivers.SPI, resetPin, dcPin, csPin, blPin machine.Pin) Device {
+func New(bus drivers.SPI, resetPin, dcPin, csPin, blPin drivers.PinOutput) Device {
 	return NewOf[pixel.RGB565BE](bus, resetPin, dcPin, csPin, blPin)
 }
 
 // NewOf creates a new ST7735 connection with a particular pixel format. The SPI
 // wire must already be configured.
-func NewOf[T Color](bus drivers.SPI, resetPin, dcPin, csPin, blPin machine.Pin) DeviceOf[T] {
-	dcPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	resetPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	csPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
-	blPin.Configure(machine.PinConfig{Mode: machine.PinOutput})
+func NewOf[T Color](bus drivers.SPI, resetPin, dcPin, csPin, blPin drivers.PinOutput) DeviceOf[T] {
 	return DeviceOf[T]{
 		bus:      bus,
-		dcPin:    dcPin,
-		resetPin: resetPin,
-		csPin:    csPin,
-		blPin:    blPin,
+		dcPin:    legacy.PinOutput(dcPin),
+		resetPin: legacy.PinOutput(resetPin),
+		csPin:    legacy.PinOutput(csPin),
+		blPin:    legacy.PinOutput(blPin),
 	}
 }
 
@@ -114,11 +110,11 @@ func (d *DeviceOf[T]) Configure(cfg Config) {
 	d.batchData = pixel.NewImage[T](int(d.batchLength), 1)
 
 	// reset the device
-	d.resetPin.High()
+	d.resetPin.Set(true)
 	time.Sleep(5 * time.Millisecond)
-	d.resetPin.Low()
+	d.resetPin.Set(false)
 	time.Sleep(20 * time.Millisecond)
-	d.resetPin.High()
+	d.resetPin.Set(true)
 	time.Sleep(150 * time.Millisecond)
 
 	// Common initialization
@@ -226,7 +222,7 @@ func (d *DeviceOf[T]) Configure(cfg Config) {
 
 	d.SetRotation(d.rotation)
 
-	d.blPin.High()
+	d.blPin.Set(true)
 }
 
 // Display does nothing, there's no buffer as it might be too big for some boards
@@ -438,9 +434,9 @@ func (d *DeviceOf[T]) Size() (w, h int16) {
 // EnableBacklight enables or disables the backlight
 func (d *DeviceOf[T]) EnableBacklight(enable bool) {
 	if enable {
-		d.blPin.High()
+		d.blPin.Set(true)
 	} else {
-		d.blPin.Low()
+		d.blPin.Set(false)
 	}
 }
 

tinygo/pin.go

@@ -0,0 +1,39 @@
+//go:build baremetal && tinygo
+
+package tinygo // import "tinygo.org/x/drivers/tinygo"
+
+import "machine"
+
+// tinygo.Pin wraps machine.Pin to ensure correct pin mode is set when Get or Set methods are called.
+
+type Pin struct {
+	pin  machine.Pin
+	mode machine.PinMode
+
+	modeSet   bool
+	inputMode machine.PinMode
+}
+
+func New(pin machine.Pin) *Pin {
+	return &Pin{pin: pin, inputMode: machine.PinInput}
+}
+
+func NewWithInputMode(pin machine.Pin, inputMode machine.PinMode) *Pin {
+	return &Pin{pin: pin, inputMode: inputMode}
+}
+
+func (p *Pin) Get() bool {
+	if !p.modeSet || p.mode != p.inputMode {
+		p.pin.Configure(machine.PinConfig{Mode: p.inputMode})
+		p.mode = machine.PinInput
+	}
+	return p.pin.Get()
+}
+
+func (p *Pin) Set(high bool) {
+	if !p.modeSet || p.mode != machine.PinOutput {
+		p.pin.Configure(machine.PinConfig{Mode: machine.PinOutput})
+		p.mode = machine.PinOutput
+	}
+	p.pin.Set(high)
+}

version.go

@@ -2,4 +2,4 @@ package drivers
 
 // Version returns a user-readable string showing the version of the drivers package for support purposes.
 // Update this value before release of new version of software.
-const Version = "0.32.0"
+const Version = "0.33.0"

ws2812/ws2812-asm_cortexm.go

@@ -931,6 +931,356 @@ void ws2812_writeByte125(char c, uint32_t *portSet, uint32_t *portClear, uint32_
 	  [portClear]"m"(*portClear));
 }
 
+__attribute__((always_inline))
+void ws2812_writeByte150(char c, uint32_t *portSet, uint32_t *portClear, uint32_t maskSet, uint32_t maskClear) {
+	// Timings:
+	// T0H: 53 - 55 cycles or 353.3ns - 366.7ns
+	// T1H: 158 - 160 cycles or 1053.3ns - 1066.7ns
+	// TLD: 173 -    cycles or 1153.3ns -
+	uint32_t value = (uint32_t)c << 24;
+	char i = 8;
+	__asm__ __volatile__(
+		"1: @ send_bit\n"
+		"\t  str   %[maskSet], %[portSet]     @ [2]   T0H and T0L start here\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  lsls  %[value], #1               @ [1]\n"
+		"\t  bcs.n 2f                         @ [1/3] skip_store\n"
+		"\t  str   %[maskClear], %[portClear] @ [2]   T0H -> T0L transition\n"
+		"\t2: @ skip_store\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  str   %[maskClear], %[portClear] @ [2]   T1H -> T1L transition\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  nop\n"
+		"\t  subs  %[i], #1                   @ [1]\n"
+		"\t  beq.n 3f                         @ [1/3] end\n"
+		"\t  b     1b                         @ [1/3] send_bit\n"
+		"\t3: @ end\n"
+	: [value]"+r"(value),
+	  [i]"+r"(i)
+	: [maskSet]"r"(maskSet),
+	  [portSet]"m"(*portSet),
+	  [maskClear]"r"(maskClear),
+	  [portClear]"m"(*portClear));
+}
+
 __attribute__((always_inline))
 void ws2812_writeByte168(char c, uint32_t *portSet, uint32_t *portClear, uint32_t maskSet, uint32_t maskClear) {
 	// Timings:
@@ -1832,6 +2182,16 @@ func (d Device) writeByte125(c byte) {
 	interrupt.Restore(mask)
 }
 
+func (d Device) writeByte150(c byte) {
+	portSet, maskSet := d.Pin.PortMaskSet()
+	portClear, maskClear := d.Pin.PortMaskClear()
+
+	mask := interrupt.Disable()
+	C.ws2812_writeByte150(C.char(c), (*C.uint32_t)(unsafe.Pointer(portSet)), (*C.uint32_t)(unsafe.Pointer(portClear)), C.uint32_t(maskSet), C.uint32_t(maskClear))
+
+	interrupt.Restore(mask)
+}
+
 func (d Device) writeByte168(c byte) {
 	portSet, maskSet := d.Pin.PortMaskSet()
 	portClear, maskClear := d.Pin.PortMaskClear()

ws2812/ws2812.go

@@ -1,7 +1,7 @@
 // Package ws2812 implements a driver for WS2812 and SK6812 RGB LED strips.
 package ws2812 // import "tinygo.org/x/drivers/ws2812"
 
-//go:generate go run gen-ws2812.go -arch=cortexm 16 48 64 120 125 168 200
+//go:generate go run gen-ws2812.go -arch=cortexm 16 48 64 120 125 150 168 200
 //go:generate go run gen-ws2812.go -arch=tinygoriscv 160 320
 
 import (

ws2812/ws2812_cortexm.go

@@ -31,6 +31,9 @@ func (d Device) WriteByte(c byte) error {
 	case 125_000_000: // 125 MHz e.g. rp2040 originally
 		d.writeByte125(c)
 		return nil
+	case 150_000_000: // 150MHz, e.g. rp2350
+		d.writeByte150(c)
+		return nil
 	case 168_000_000: // 168MHz, e.g. stm32f405
 		d.writeByte168(c)
 		return nil