all: add HiFive1 rev B board with RISC-V architecture

This page has been a big help in adding support for this new chip:
https://wiki.osdev.org/HiFive-1_Bare_Bones

src/machine/board_fe310.go

@@ -0,0 +1,38 @@
+// +build hifive1b
+
+package machine
+
+const (
+	P00 Pin = 0
+	P01 Pin = 1
+	P02 Pin = 2
+	P03 Pin = 3
+	P04 Pin = 4
+	P05 Pin = 5
+	P06 Pin = 6
+	P07 Pin = 7
+	P08 Pin = 8
+	P09 Pin = 9
+	P10 Pin = 10
+	P11 Pin = 11
+	P12 Pin = 12
+	P13 Pin = 13
+	P14 Pin = 14
+	P15 Pin = 15
+	P16 Pin = 16
+	P17 Pin = 17
+	P18 Pin = 18
+	P19 Pin = 19
+	P20 Pin = 20
+	P21 Pin = 21
+	P22 Pin = 22
+	P23 Pin = 23
+	P24 Pin = 24
+	P25 Pin = 25
+	P26 Pin = 26
+	P27 Pin = 27
+	P28 Pin = 28
+	P29 Pin = 29
+	P30 Pin = 30
+	P31 Pin = 31
+)

src/machine/board_hifive1b.go

@@ -0,0 +1,19 @@
+// +build hifive1b
+
+package machine
+
+const (
+	LED       = LED1
+	LED1      = LED_RED
+	LED2      = LED_GREEN
+	LED3      = LED_BLUE
+	LED_RED   = P22
+	LED_GREEN = P19
+	LED_BLUE  = P21
+)
+
+const (
+	// TODO: figure out the pin numbers for these.
+	UART_TX_PIN = NoPin
+	UART_RX_PIN = NoPin
+)

src/machine/i2c.go

@@ -1,4 +1,4 @@
-// +build !stm32f4disco
+// +build !stm32f4disco,!hifive1b
 
 package machine
 

src/machine/machine_fe310.go

@@ -0,0 +1,54 @@
+// +build fe310
+
+package machine
+
+import (
+	"device/sifive"
+)
+
+type PinMode uint8
+
+const (
+	PinInput PinMode = iota
+	PinOutput
+)
+
+// Configure this pin with the given configuration.
+func (p Pin) Configure(config PinConfig) {
+	sifive.GPIO0.INPUT_EN.SetBits(1 << uint8(p))
+	if config.Mode == PinOutput {
+		sifive.GPIO0.OUTPUT_EN.SetBits(1 << uint8(p))
+	}
+}
+
+// Set the pin to high or low.
+func (p Pin) Set(high bool) {
+	if high {
+		sifive.GPIO0.PORT.SetBits(1 << uint8(p))
+	} else {
+		sifive.GPIO0.PORT.ClearBits(1 << uint8(p))
+	}
+}
+
+type UART struct {
+	Bus    *sifive.UART_Type
+	Buffer *RingBuffer
+}
+
+var (
+	UART0 = UART{Bus: sifive.UART0, Buffer: NewRingBuffer()}
+)
+
+func (uart UART) Configure(config UARTConfig) {
+	// Assuming a 16Mhz Crystal (which is Y1 on the HiFive1), the divisor for a
+	// 115200 baud rate is 138.
+	sifive.UART0.DIV.Set(138)
+	sifive.UART0.TXCTRL.Set(sifive.UART_TXCTRL_ENABLE)
+}
+
+func (uart UART) WriteByte(c byte) {
+	for sifive.UART0.TXDATA.Get()&sifive.UART_TXDATA_FULL != 0 {
+	}
+
+	sifive.UART0.TXDATA.Set(uint32(c))
+}

src/machine/machine_generic.go

@@ -1,4 +1,4 @@
-// +build !avr,!nrf,!sam,!stm32
+// +build !avr,!nrf,!sam,!sifive,!stm32
 
 package machine
 

src/machine/spi.go

@@ -1,4 +1,4 @@
-// +build !stm32f407,!avr
+// +build !stm32f407,!avr,!hifive1b
 
 package machine
 

src/machine/uart.go

@@ -1,4 +1,4 @@
-// +build avr nrf sam stm32
+// +build avr nrf sam sifive stm32
 
 package machine