add rp2040, pico

adds preliminary support (just enough to run blinky1) for the Raspberry Pi Pico board along with the rp2040 mcu.

targets/pico.json

@@ -0,0 +1,10 @@
+{
+    "inherits": [
+        "rp2040"
+    ],
+    "build-tags": ["pico"],
+    "linkerscript": "targets/pico.ld",
+    "extra-files": [
+        "targets/pico_boot_stage2.S"
+    ]
+}

targets/pico.ld

@@ -0,0 +1,31 @@
+
+MEMORY
+{
+    FLASH_TEXT (rx) : ORIGIN = 0x10000000, LENGTH = 2048k
+}
+
+SECTIONS
+{
+    /* Second stage bootloader is prepended to the image. It must be 256 bytes big
+       and checksummed. It is usually built by the boot_stage2 target
+       in the Raspberry Pi Pico SDK
+    */
+
+    .boot2 : {
+        __boot2_start__ = .;
+        KEEP (*(.boot2))
+        __boot2_end__ = .;
+    } > FLASH_TEXT
+
+    ASSERT(__boot2_end__ - __boot2_start__ == 256,
+        "ERROR: Pico second stage bootloader must be 256 bytes in size")
+
+    /* The second stage will always enter the image at the start of .text.
+       The debugger will use the ELF entry point, which is the _entry_point
+       symbol if present, otherwise defaults to start of .text.
+       This can be used to transfer control back to the bootrom on debugger
+       launches only, to perform proper flash setup.
+    */
+}
+
+INCLUDE "targets/rp2040.ld"

targets/pico_boot_stage2.S

@@ -0,0 +1,23 @@
+// Padded and checksummed version of: /home/rkanchan/src/pico-sdk/build/src/rp2_common/boot_stage2/bs2_default.bin
+
+.cpu cortex-m0plus
+.thumb
+
+.section .boot2, "ax"
+
+.byte 0x00, 0xb5, 0x32, 0x4b, 0x21, 0x20, 0x58, 0x60, 0x98, 0x68, 0x02, 0x21, 0x88, 0x43, 0x98, 0x60
+.byte 0xd8, 0x60, 0x18, 0x61, 0x58, 0x61, 0x2e, 0x4b, 0x00, 0x21, 0x99, 0x60, 0x02, 0x21, 0x59, 0x61
+.byte 0x01, 0x21, 0xf0, 0x22, 0x99, 0x50, 0x2b, 0x49, 0x19, 0x60, 0x01, 0x21, 0x99, 0x60, 0x35, 0x20
+.byte 0x00, 0xf0, 0x44, 0xf8, 0x02, 0x22, 0x90, 0x42, 0x14, 0xd0, 0x06, 0x21, 0x19, 0x66, 0x00, 0xf0
+.byte 0x34, 0xf8, 0x19, 0x6e, 0x01, 0x21, 0x19, 0x66, 0x00, 0x20, 0x18, 0x66, 0x1a, 0x66, 0x00, 0xf0
+.byte 0x2c, 0xf8, 0x19, 0x6e, 0x19, 0x6e, 0x19, 0x6e, 0x05, 0x20, 0x00, 0xf0, 0x2f, 0xf8, 0x01, 0x21
+.byte 0x08, 0x42, 0xf9, 0xd1, 0x00, 0x21, 0x99, 0x60, 0x1b, 0x49, 0x19, 0x60, 0x00, 0x21, 0x59, 0x60
+.byte 0x1a, 0x49, 0x1b, 0x48, 0x01, 0x60, 0x01, 0x21, 0x99, 0x60, 0xeb, 0x21, 0x19, 0x66, 0xa0, 0x21
+.byte 0x19, 0x66, 0x00, 0xf0, 0x12, 0xf8, 0x00, 0x21, 0x99, 0x60, 0x16, 0x49, 0x14, 0x48, 0x01, 0x60
+.byte 0x01, 0x21, 0x99, 0x60, 0x01, 0xbc, 0x00, 0x28, 0x00, 0xd0, 0x00, 0x47, 0x12, 0x48, 0x13, 0x49
+.byte 0x08, 0x60, 0x03, 0xc8, 0x80, 0xf3, 0x08, 0x88, 0x08, 0x47, 0x03, 0xb5, 0x99, 0x6a, 0x04, 0x20
+.byte 0x01, 0x42, 0xfb, 0xd0, 0x01, 0x20, 0x01, 0x42, 0xf8, 0xd1, 0x03, 0xbd, 0x02, 0xb5, 0x18, 0x66
+.byte 0x18, 0x66, 0xff, 0xf7, 0xf2, 0xff, 0x18, 0x6e, 0x18, 0x6e, 0x02, 0xbd, 0x00, 0x00, 0x02, 0x40
+.byte 0x00, 0x00, 0x00, 0x18, 0x00, 0x00, 0x07, 0x00, 0x00, 0x03, 0x5f, 0x00, 0x21, 0x22, 0x00, 0x00
+.byte 0xf4, 0x00, 0x00, 0x18, 0x22, 0x20, 0x00, 0xa0, 0x00, 0x01, 0x00, 0x10, 0x08, 0xed, 0x00, 0xe0
+.byte 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x74, 0xb2, 0x4e, 0x7a

targets/rp2040.json

@@ -0,0 +1,12 @@
+{
+    "inherits": ["cortex-m0plus"],
+    "build-tags": ["rp2040", "rp"],
+    "flash-method": "msd",
+    "msd-volume-name": "RPI-RP2",
+    "msd-firmware-name": "firmware.uf2",
+    "binary-format": "uf2",
+    "uf2-family-id": "0xe48bff56",
+    "extra-files": [
+        "src/device/rp/rp2040.s"
+    ]
+}

targets/rp2040.ld

@@ -0,0 +1,9 @@
+
+MEMORY
+{
+    RAM (rwx)       : ORIGIN = 0x20000000, LENGTH = 256k
+}
+
+_stack_size = 2K;
+
+INCLUDE "targets/arm.ld"