Add bmp388 support (#219)

bmp388: add support

bmp388/registers.go

@@ -0,0 +1,84 @@
+// Package bmp388 provides a driver for Bosch's BMP388 digital temperature & pressure sensor.
+// The datasheet can be found here: https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bmp388-ds001.pdf
+package bmp388
+
+const Address byte = 0x77 // default I2C address
+
+const (
+	RegChipId  byte = 0x00 // useful for checking the connection
+	RegCali    byte = 0x31 // pressure & temperature compensation calibration coefficients
+	RegPress   byte = 0x04 // start of pressure data registers
+	RegTemp    byte = 0x07 // start of temperature data registers
+	RegPwrCtrl byte = 0x1B // measurement mode & pressure/temperature sensor power register
+	RegOSR     byte = 0x1C // oversampling settings register
+	RegODR     byte = 0x1D //
+	RegCmd     byte = 0x7E // miscellaneous command register
+	RegStat    byte = 0x03 // sensor status register
+	RegErr     byte = 0x02 // error status register
+	RegIIR     byte = 0x1F
+)
+
+const (
+	ChipId    byte = 0x50 // correct response if reading from chip id register
+	PwrPress  byte = 0x01 // power on pressure sensor
+	PwrTemp   byte = 0x02 // power on temperature sensor
+	SoftReset byte = 0xB6 // command to reset all user configuration
+	DRDYPress byte = 0x20 // for checking if pressure data is ready
+	DRDYTemp  byte = 0x40 // for checking if pressure data is ready
+)
+
+// The difference between forced and normal mode is the bmp388 goes to sleep after taking a measurement in forced mode.
+// Set it to forced if you intend to take measurements sporadically and want to save power. The driver will handle
+// waking the sensor up when the sensor is in forced mode.
+const (
+	Normal Mode = 0x30
+	Forced Mode = 0x16
+	Sleep  Mode = 0x00
+)
+
+// Increasing sampling rate increases precision but also the wait time for measurements. The datasheet has a table of
+// suggested values for oversampling, output data rates, and iir filter coefficients by use case.
+const (
+	Sampling1X Oversampling = iota
+	Sampling2X
+	Sampling4X
+	Sampling8X
+	Sampling16X
+	Sampling32X
+)
+
+// Output data rates in Hz. If increasing the sampling rates you need to decrease the output data rates, else the bmp388
+// will freeze and Configure() will return a configuration error message. In that case keep decreasing the data rate
+// until the bmp is happy
+const (
+	Odr200 OutputDataRate = iota
+	Odr100
+	Odr50
+	Odr25
+	Odr12p5
+	Odr6p25
+	Odr3p1
+	Odr1p5
+	Odr0p78
+	Odr0p39
+	Odr0p2
+	Odr0p1
+	Odr0p05
+	Odr0p02
+	Odr0p01
+	Odr0p006
+	Odr0p003
+	Odr0p0015
+)
+
+// IIR filter coefficients, higher values means steadier measurements but slower reaction times
+const (
+	Coeff0 FilterCoefficient = iota
+	Coeff1
+	Coeff3
+	Coeff7
+	Coeff15
+	Coeff31
+	Coeff63
+	Coeff127
+)