Add praline gpio (#3218)

* Implement antenna bias control for Praline and update GPIO configurations
* Add GPIO power management functions and update board initialization for Praline
* Refactor power management functions for Praline and update GPIO configurations
* Update GPIO configurations for Praline and enable power control pins. AA_EN enabled
* Refactor GPIO configuration for Praline: update array size definitions and clean up comments
* Add P1 and P2 control functions for PRALINE
* Introduced P1_Function and P2_Function enums in ClockManager to manage multiplexer control.
* mplemented set_p1_control and set_p2_control methods for configuring P1 and P2 control pins based on specified functions.
* Updated clock_manager.hpp and clock_manager.cpp to include new functionality.
* Modified MAX2837 and MAX2839 initialization to conditionally configure GPIO based on PRALINE.
* Adjusted RFFC507x and RFFC507x_SPI initialization to include GPIO setup for PRALINE.
- Refactored RF path initialization to remove unnecessary GPIO setup.
- Updated board configuration for PRALINE to reflect new GPIO settings and pin configurations.
- Cleaned up FPGA bridge code by removing unused pin configuration functions.
- Adjusted SCU array size in pal_lld.h for PRALINE.
- Enhanced hackrf_gpio.hpp to define multiplexer control pins for PRALINE.
- Modified LED setup to accommodate active-low configuration for PRALINE.

* Refactor GPIO and power control functions

- Removed unused power control function declarations from board.h.
- Enhanced gpio.hpp with new pin setup functions and GPIO control structures for PRALINE.
- Consolidated multiplexer control pin definitions into gpio_control namespace.
- Moved power control function implementations to gpio.cpp, including detailed VAA power management logic.
- Updated power control functions to handle both PRALINE and HackRF R9 configurations.
- Cleaned up hackrf_gpio.hpp by removing redundant multiplexer control definitions.

* Refactor GPIO control for PRALINE: update MAX2831 and RFFC507x configurations, add new GPIO mappings

* Refactor GPIO configurations for PRALINE: update anti-aliasing filter pin mapping, enhance LED setup logic, and add placeholder GPIO entries.

* Refactor GPIO configurations for PRALINE: update LED mappings and remove unused anti-aliasing filter GPIO entry.

firmware/application/hw/max2837.cpp

@@ -99,9 +99,11 @@ constexpr uint32_t pll_factor = 1.0 / (4.0 / 3.0 / reference_frequency) + 0.5;
 void MAX2837::init() {
     set_mode(Mode::Shutdown);
 
+#ifndef PRALINE
     gpio_max283x_enable.output();
     gpio_max2837_rxenable.output();
     gpio_max2837_txenable.output();
+#endif
 
     _map.r.tx_gain.TXVGA_GAIN_SPI_EN = 1;
     _map.r.tx_gain.TXVGA_GAIN_MSB_SPI_EN = 1;
@@ -157,9 +159,11 @@ void MAX2837::set_tx_LO_iq_phase_calibration(const size_t v) {
     // TX calibration , Logic pins , ENABLE, RXENABLE, TXENABLE = 1,0,1 (5dec), and  Reg address 16, D1 (CAL mode 1):DO (CHIP ENABLE 1)
     set_mode(Mode::Tx_Calibration);  // write to ram 3 LOGIC Pins .
 
+#ifndef PRALINE
     gpio_max283x_enable.output();
     gpio_max2837_rxenable.output();
     gpio_max2837_txenable.output();
+#endif
 
     _map.r.spi_en.CAL_SPI = 1;  // Register Settings reg address 16,  D1 (CAL mode 1)
     _map.r.spi_en.EN_SPI = 1;   // Register Settings reg address 16,  DO (CHIP ENABLE 1)
@@ -348,9 +352,11 @@ void MAX2837::set_rx_LO_iq_phase_calibration(const size_t v) {
     // RX calibration , Logic pins , ENABLE, RXENABLE, TXENABLE = 1,1,0 (3dec), and  Reg address 16, D1 (CAL mode 1):DO (CHIP ENABLE 1)
     set_mode(Mode::Rx_Calibration);  // write to ram 3 LOGIC Pins .
 
+#ifndef PRALINE
     gpio_max283x_enable.output();
     gpio_max2837_rxenable.output();
     gpio_max2837_txenable.output();
+#endif
 
     _map.r.spi_en.CAL_SPI = 1;  // Register Settings reg address 16,  D1 (CAL mode 1)
     _map.r.spi_en.EN_SPI = 1;   // Register Settings reg address 16,  DO (CHIP ENABLE 1)